Page 2 - ii; IMPORTANT SAFETY INSTRUCTIONS; SAVE THESE INSTRUCTIONS
i 2022 ISDN Teleset ii Mandatory Customer Information Federal Communications Commission (FCC) Requirements This equipment complies with Part 68 of the FCC Rules. The FCC registration information is located on a label affixed to the bottom of the Teleset. If requested, you must provide the telephone ...
Page 4 - TABLE OF FIGURES; INTRODUCTION; ABOUT THIS MANUAL
i 2022 ISDN Teleset 2 TABLE OF FIGURES F IGURE 1: L INE AND P OWER J ACKS ............................................................................................................................................ 5 F IGURE 2: NT1 L EADS ................................................................
Page 5 - FEATURES; VOICE OPERATION FEATURES
i 2022 ISDN Teleset 3 FEATURES The i 2022 Teleset offers an extensive list of features. They include the following: Cross-Compatibility The Telesets work with several different switches: the Lucent Technologies 5ESS ® (Custom and National ISDN), the Nortel DMS-100 ® (National ISDN), the Siemens EWSD...
Page 6 - ACCESSORIES; INSTALLATION; PARTS LIST
i 2022 ISDN Teleset 4 Call Timer On each new call, the timer displays the elapsed time of the call. Placing a new call resets the timer for the new call. Headset Jack Inserting the headset plug into this jack enables the headset, and disables the speakerphone. The i 2022 Teleset contains an amplifie...
Page 7 - ISDN INTERFACES; Line and Power Jacks; LINE AND POWER CONNECTIONS – i2022 TELESET; i2022 Equipped with an S Interface Module; Power Switch; When the
i 2022 ISDN Teleset 5 ISDN INTERFACES A little background information sometimes helps. Your ISDN service comes to you over ordinary telephone line wiring. That makes it less expensive and simple to install. There are a number of interfaces defined in Basic Rate ISDN. The most common of these interfa...
Page 8 - PS1/PS2 SWITCH SETTINGS; Table 2; Powering the i2022 Locally
i 2022 ISDN Teleset 6 Figure 2: NT1 Leads PS1/PS2 SWITCH SETTINGS The i 2022 requires PS2 power. Always leave the PS1/PS2 switch in the PS2 position. Figure 3: S Interface Module Power Switch TERMINATING RESISTOR SETTINGS Options 1 2 3 4 5 Open OFF OFF - - - 100 Ω ON ON - - - The default setting is ...
Page 9 - from a common power supply.
i 2022 ISDN Teleset 7 Figure 4: Using Lucent 1215B Power Supply Figure 5: Powering a Teleset (S/T) with an External Power Supply Fig. 5 shows an i 2022 connected to an S/T Interface. The U Interface is connected to the NT1. The output of the NT1 is an S/T Interface with power for the Teleset. The S/...
Page 10 - TERMINATING RESISTORS; The; ON; position, the Terminating Resistors are installed. The; PASSIVE-BUS OR MULTIPOINT; Farthest Teleset
i 2022 ISDN Teleset 8 TERMINATING RESISTORS The i 2022Teleset S Interface module has built-in Terminating Resistors. The Terminating Resistor switches are located on the top of the Interface Module. When the switches are in the ON position, the Terminating Resistors are installed. The value of the r...
Page 11 - i2022 EQUIPPED WITH A U INTERFACE MODULE; On
i 2022 ISDN Teleset 9 In the following application, the NT1 is equal in distance to both i 2022 phones. The Terminating Resistors are set to “On” at one of the phones and at the NT1. Figure 8: Equal Distance Telesets i2022 EQUIPPED WITH A U INTERFACE MODULE The i 2022 is available with an optional U...
Page 12 - LINE CONFIGURATION; Directory Number
i 2022 ISDN Teleset 10 1. If the S Interface Jack is not used and the i 2022 is the only device, set the Terminating Resistor switches to 50 Ω . 2. If there is a device connected to the S Interface, set the Terminating Resistor switches to 100 Ω . 3. If the S Interface Jack is not used and the i 202...
Page 13 - INSTALLING THE LOGO PLATE; Inserting and removing the modules
i 2022 ISDN Teleset 11 INSTALLING THE LOGO PLATE ASSEMBLING THE i2022 Inserting and removing the modules The i 2022 Teleset requires either an S Interface module or a U Interface Module. There are also optional Data Modules available. There are two slots on the bottom of the i 2022. The S and U modu...
Page 14 - SOFTKEYS
i 2022 ISDN Teleset 12 SOFTKEYS Directly below the display are four softkeys, vertically-oriented to the display. The location of these keys corresponds to menu choices that appear directly above them in the LCD window. For example, pressing the softkey below the “clock” menu reveals the options for...
Page 15 - Setup
i 2022 ISDN Teleset 13 Example: Press the softkey under Directory - shown below by highlighting ( bold type) the word “ DIR ” and highlighting the softkey below that menu item. Pressing the Directory softkey brings up the second menu with additional choices. In our example we chose Search next - sho...
Page 16 - Auto-SPID Procedures; WARNING: DEFAULTING THE i2022 WILL ERASE ALL OF THE MEMORY.
i 2022 ISDN Teleset 14 The Auto-Install programming choices are: Adjust Contrast – Select Yes or No. The i 2022 may display a wait message and start a countdown. This is the T- Wait timer. SPID – If the switch supports Auto-SPID you will be prompted to choose a SPID. If your switch does not support ...
Page 17 - Next; When the correct SPID is displayed, press the; softkey to choose it.; Next Prev; Select; Prompt; MORE is; not lit
i 2022 ISDN Teleset 15 If the switch supports Auto-SPID, the i 2022 will display all of the SPIDs available on the line in the following format: If the SPID displayed is not the correct SPID for your application, press the Next key. Pressing the Detail softkey will display the SPID, the Primary Dire...
Page 18 - Auto Bkspc Save; MORE
i 2022 ISDN Teleset 16 Connecting the I2022- Manual-install 1. Assemble the i 2022 2. Verify the PS1/PS2 switch located on the Interface Module is in the PS2 position. See page 6 for further information on setting the PS1/PS2 switch. 3. Verify the Terminating Resistor (TR) switch is set correctly. S...
Page 20 - Teleset is not in the default condition.
i 2022 ISDN Teleset 18 Manually Programming Call Appearances Take a look at the layout of the Line and Call Appearance keys. These (32) keys are located on the far-right hand side of the phone. The upper-left-hand key is the default or primary key. This key must remain a Call Appearance key. All of ...
Page 21 - After the DN has been entered, press the; Beare; r softkey until the Bearer Service of Speech is displayed.; Save; . The display will now allow you to move to the second DN.
i 2022 ISDN Teleset 19 After the DN has been entered, press the Beare r softkey until the Bearer Service of Speech is displayed. Since the first DN, 847-555-4736 has only two Call Appearances and there are three Call Appearances lit, press the third CA key to turn that CA off. After you completed th...
Page 23 - SETTING UP THE TELESET
i 2022 ISDN Teleset 21 2. Press FA to scroll the features on the display. 3. The following features: PkUp (Call Pickup), Fwdon (Call Forwarding), Confr (Conference), Transfer , Drop , MsgWt 1 (Message Waiting 1) and MsgWt 2 (Message Waiting 2) are enabled as you scroll though them. If the switch is ...
Page 25 - Press; the; MENU
i 2022 ISDN Teleset 23 Press MENU to exit. Setting the Date and Time Clock Setting the time and date are important to the accuracy of your Teleset. This is important because the alarm clock and the Call Log features are dependent on setting the correct time and date. The graphic flowchart may be use...
Page 27 - Call Appearance : 3
i 2022 ISDN Teleset 25 Each call appearance can ring with a different sound. This is done by pressing any call appearance key and choosing a ring pattern (0-9) or silent alerting (#) and then pressing Accept. As an example, we press the digit 3 on the keypad or press call appearance 3, then choose a...
Page 30 - To return to Manual Answer, press the; Manual Answer; to bring up the menu shown below. When it appears press the; SpDial; key to abort the
i 2022 ISDN Teleset 28 To return to Manual Answer, press the Manual Answer key. Speed Dial Key Assignment You can assign Speed Dial numbers to individual hardkeys. Programmable hardkeys may only be assigned to a single function/feature. If a hardkey is already assigned, it cannot also be used for a ...
Page 33 - PASSWORD SELECTION
i 2022 ISDN Teleset 31 3. Enter the date you want the alarm to sound, or press Daily , then press Save . 4. Enter the time (hour, minute), then press Save . If you wish to enter additional alarms press Next and repeat the above. PASSWORD SELECTION A password (numeric) can safeguard your directory en...
Page 34 - softkey; LANGUAGE OPTIONS; OPERATIONS; VOICE OPERATION
i 2022 ISDN Teleset 32 5. This number is your password. Write it down. You are prompted to confirm the password. 6. To begin Level 2 protection, press the lit MENU hardkey now. Do not press the Menus softkey. Level 2 protection is now set. 7. To begin Level 3 protection, enter your password and pres...
Page 39 - TELESET FEATURES; REDIAL
i 2022 ISDN Teleset 37 Conferencing an Outgoing Call to an Incoming Call 1. Place the outgoing call on Hold by using the Hold key. 2. The outgoing Call Appearance will flash red. 3. Answer the incoming call. 4. Press the Conf (conference) softkey and the phone adds dial tone from another Call Appear...
Page 42 - DIALING OPTIONS; Setting the Dialing Options; and then press; Control Type : NonUse
i 2022 ISDN Teleset 40 DIALING OPTIONS Dialing Options allow the user to automatically add prefix digits or strip off digits, which are not needed from Directory Numbers recorded in the call log. For example, a digit 9 is required when dialing calls outside your business group. In order to dial this...
Page 43 - Control Type : Semi Auto; Inside Dialing : 7 Digit
i 2022 ISDN Teleset 41 To set the Control type press Change . In our illustration we will use Semi Auto, since it will be the most commonly used option. Press SemiAu and then press Save . After the Control Type is chosen, enter your Phone Number (Directory number) as a 10 digit number. Use the Bkspc...
Page 44 - Inside Dialing : 4 Digit
i 2022 ISDN Teleset 42 Outside Code – This is the prefix you dial to reach a phone number outside of your business group. This is usually a 9. Local Calls – This is the number of digits required to dial a local call after the Outside Code is dialed. Choices are 7 digit, 10 digit or 1+10 digit. Press...
Page 45 - CALL RECORDS
i 2022 ISDN Teleset 43 CALL RECORDS Your Teleset stores call activity records in electronic memory. The softkey CalLog will change to NewLog upon receipt of an unanswered incoming call to Prime Call Appearances. To access to the call records, press the CalLog , or NewLog , softkey on the startup scr...
Page 46 - Ed’s Garage; Dial; Prev Edit Clear
i 2022 ISDN Teleset 44 If the dial option is set to Semi Auto, the following display is returned. Select Inside if the call is within your Business Group. Select Outside if the call is outside of your Business Group. If the Dial Option is set to Auto, the call will be dialed. Saving a CalLog Entry t...
Page 47 - DN; ADVANCED FEATURES; ANALOG PORT; Analog Port Sharing the Teleset’s SPID – Configuring
i 2022 ISDN Teleset 45 When the number is transferred to the Directory, you have an opportunity to edit the name. Use the ∗ key to enter an asterisk or a hyphen. Use the # key to enter a pound sign or apostrophe. Use the DN softkey to toggle between the Name and the Telephone number. Use the - key f...
Page 48 - POTS; Serviced as Voice
i 2022 ISDN Teleset 46 To configure the i 2022 for Analog Port Sharing the Teleset’s SPID, press MENU , MORE , MORE , Config , MORE , MORE , SPID , Change , Save . The display will show Pressing POTS will change the “Serviced as” line in the display to “Serviced as Voice and POTS”. Press MENU to sav...
Page 50 - CORDLESS
i 2022 ISDN Teleset 48 Outgoing calls can be placed from the Analog Port. The analog icons will show the on-hook/off-hook status of the analog call. CALL BLOCKING TONE The i 2022 will furnish an audible tone if there is no B-Channel available. This tone will notify the user there is no talk path bet...
Page 51 - Lights if one of the B-Channels is in the Data Mode.; DATA; key to a General CA key.
i 2022 ISDN Teleset 49 Off-Hook -- The icon on the right is displayed when the Analog Port is programmed and the Analog Call Appearance is off-hook. HEADSET – The Headset icon will light when the Handset/Headset option is in the Headset mode. INTERCOM -- Lights when Intercom is set to Auto Answer. I...
Page 53 - When the feature softkey to be removed is displayed, press; Clear; KEY MAPPING; MapFA; and the display will be as shown below.
i 2022 ISDN Teleset 51 When the feature softkey to be removed is displayed, press Clear . In the following display FwdOn (Call Forward) was cleared. KEY MAPPING The i 2022 supports a local feature called Key Mapping. The purpose of the Key Mapping feature is to allow features that have Feature Activ...
Page 54 - VIEW
i 2022 ISDN Teleset 52 Press the hardkey that you would like to remap. If you select a key that is not available you will be prompted to “Try Another Key.” When you select an available key the display will show: Press MENU to exit the idle menu. At this point the hardkey you selected will be the Fea...
Page 55 - PROTECTING KEYS FROM BEING OVERWRITTEN; and then
i 2022 ISDN Teleset 53 The Teleset will light the appropriate Call Appearance keys and display the DN assigned to them. This is helpful when checking Multiple Call Appearances or labeling the Teleset. PROTECTING KEYS FROM BEING OVERWRITTEN (This procedure is not necessary On 5ESS Custom ISDN or firm...
Page 57 - MAINTAINING THE TELESET; CHECKING THE FW VERSION
i 2022 ISDN Teleset 55 MAINTAINING THE TELESET CHECKING THE FW VERSION If you experience a problem with the i 2022 you may be asked to verify the firmware version. To check the FW version of the i 2022, press MENU , View , Version . The display will show the version number. LOADING FW Firmware can b...
Page 58 - Calls Blocked; GLOSSARY
i 2022 ISDN Teleset 56 Calls Blocked No B-Channel available 1. B-Channel in use by another station on the bus. 2. Teleset programmed with a single SPID and an Analog Port. Either the Teleset can be used or the Analog Port can be used but not at the same time. GLOSSARY The definitions in this Glossar...
Page 60 - INDEX; Caller ID; Calls; LCD
i 2022 ISDN Teleset ii INDEX A accessories, 4 alarm, 3, 30, 31 amplifier, 4 Auto Install, 13 SPID, 14 Switch, 14 Auto-Callback, 4 Auto-SPID, 10 Auto-Switch, 10 B Busy Lamp Field, 49, 50 C Call Appearance, 3, 10, 26, 32, 34, 35, 56, 57 ConfCA, 26 Call Forwarding, 4, 21 Call Pickup, 4, 21 Caller ID , ...