Nortel 8672ATMM - Manuals

National Electromagnetic Compliance (EMC) Statements of Compliance 7 European Union and European Free Trade Association (EFTA) Notice All products labeled with the CE marking comply with R&TTE Directive(1999/5/EEC) which includes the Electromagnetic Compliance (EMC)Directive (2004/108/EC) and th...

8 Regulatory Information and Safety Precautions National Safety Statements of Compliance CE Marking Statement (Europe only) EN 60 950 Statement This is to certify that the Nortel 8000 Series chassis and componentsinstalled within the chassis are in compliance with the requirements of EN60 950 in acc...

Safety Messages 11 Safety Messages This section describes the different precautionary notices used in thisdocument. This section also contains precautionary notices that you mustread for safe operation of the Nortel Ethernet Routing Switch 8600. Notices Notice paragraphs alert you about issues that ...

Safety Messages 15 DANGER PERICOLO Le indicazioni di pericolo forniscono informazioni per evitaresituazioni o condizioni che potrebbero causare gravi danni allepersone o il decesso. Nortel Ethernet Routing Switch 8600 Installation — Media Dependent Adapters for the 8672ATME and 8672ATMM Modules NN46...

17 . Software license This section contains the Nortel Networks software license. Nortel Networks Inc. software license agreement This Software License Agreement ("License Agreement") is betweenyou, the end-user ("Customer") and Nortel Networks Corporation andits subsidiaries and aff...

18 Software license of this Agreement. Customer shall not a) use, copy, modify, transferor distribute the Software except as expressly authorized; b) reverseassemble, reverse compile, reverse engineer or otherwise translate theSoftware; c) create derivative works or modifications unless expresslyaut...

21 . New in this release The following sections detail what’s new in Nortel Ethernet Routing Switch8600 Installation — Media Dependent Adapters for the 8672ATME and8672ATMM Modules, NN46205-316 for release 5.0. • “Features” (page 21) • “Other changes” (page 21) Features This document contains no fea...

23 . Introduction This guide describes how to install the Media Dependent Adapters (MDAs)for the 8672ATME and 8672ATMM Modules on Ethernet Routing Switch8600. Navigation • “MDA overview” (page 25) • “Media Dependent Adapter installation for the 8672ATME and8672ATMM modules ” (page 27) • “MDA and LED...

25 . MDA overview The MDAs for the Nortel 8672ATME and 8672ATMM modules are modularport adapters that are installed on the Ethernet Routing Switch 8600. The 8672 ATM modules are part of the Nortel 8000 Series line ofcommunications products. There are two versions of the ATM modules:the 8672ATME modu...

27 . Media Dependent Adapter installationfor the 8672ATME and 8672ATMMmodules This section provides procedures for installing MDA for the 8672ATMEand 8672ATMM modules. Prerequisites • Verify that you have the following tools and materials: — Phillips screwdriver #1 Navigation • “Estimated installati...

28 Media Dependent Adapter installation for the 8672ATME and 8672ATMM modules Table 2Task and estimated time (cont’d.) Task Estimated time Aligning the MDA with the front portion of the module andmounting the posts 2–5 minutes Seating MDA and tightening the screws and the label 2–5 minutes Removing ...

Replacing an MDA 31 Replacing an MDA This procedure describes how to replace an MDA. CAUTION Risk of service loss You cannot hot-swap an MDA. You must remove the8672ATME or 8672ATMM module, install the MDA, and thenreinstall the module. Procedure steps Step Action 1 Remove the 8672ATME or the 8672AT...

32 Media Dependent Adapter installation for the 8672ATME and 8672ATMM modules 5 If you do not plan to install a replacement MDA, place the slotcover on the MDA slot and tighten the two screws. --End-- Connecting fiber cables This procedure describes how to connect fiber cables to the installedMDA. T...

34 Media Dependent Adapter installation for the 8672ATME and 8672ATMM modules --End-- Connecting coaxial cables This procedure describes how to connect coaxial cables to the MDA. ATTENTION The DS-3 MDA uses bayonet Neill-Concelman (BNC) connectors. Procedure steps Step Action 1 Push the coaxial cabl...

37 . Translation of Safety messages Class A product caution statement CAUTION This device is a Class A product. Operation of this equipmentin a residential area is likely to cause harmful interference, inwhich case users are required to take appropriate measuresnecessary to correct the interference ...

38 Translation of Safety messages CAUTION CUIDADO Este dispositivo é um produto Classe A. Operar esteequipamento em uma área residencial provavelmente causaráinterferência prejudicial; neste caso, espera-se que os usuáriostomem as medidas necessárias para corrigir a interferência porsua própria cont...

41 . AppendixMDA and LED specifications See the following sections for Media Dependent Adapters (MDAs) andLight Emitting Diode (LED) specifications. MDA specifications The OC-3c/STM-1 MDA uses SONET STS-3c/SDH STM-1 1300nanometer (nm) optical transceivers with MT-RJ fiber-optic connectors andeither ...

42 MDA and LED specifications Table 4OC-3c/STM-1 MDA specifications: 8672ATME and 8672ATMM modules (cont’d.) Parameter SMF description MMF description Distance 15 km 2 km Input power 40 W 40 W Thermal rating 138 BTU/hour maximum 138 BTU/hour maximum The OC-12c/STM-4 MDA uses SONET STS-3c/SDH STM-1 1...