Nortel 241-5101-200 - Manuals

Contents 9 Passport 8250 Installation Guide R2.2 Appendix AReplacing hardware 45 Replacing a power supply module 46 Replacing a board module 47 Passport 8250 board guidelines 49 Replacing the fan module 49 Appendix BLEDs 51 Appendix CStandards 55 Product safety standards 55 Electromagnetic compatibi...

11 Passport 8250 Installation Guide R2.2 About this document This document explains how to install the Passport 8250 device. This document uses the terms DS-1/E1 and STM-1/OC-3. The term DS-1/E1is for information that applies to both DS-1 and E1 interfaces. The termSTM-1/OC-3 is for information that...

12 About this document 241-5101-200 R2.2 • “Replacing hardware” (page 45). • “LEDs” (page 51). • “Standards” (page 55). Conventions There are documentation and symbol conventions used in this document. Documentation conventions There are a number of documentation conventions you should know about. •...

About this document 13 Passport 8250 Installation Guide R2.2 • ... Three dots in a command indicate that the parameter may be repeatedmore than once in succession. Symbol conventions The following are samples of caution and warning conventions used inthis document: Related documents Documents relate...

14 About this document 241-5101-200 R2.2 NMS documents See the following NMS documents for information on how to monitor andconfigure the Passport 8250 device using the NMS Passport 8250 tools,integrating the Passport 8250 device into the NMS environment, and usingbackup and restore: • NTP 241-6001-...

Chapter 1 Passport 8250 17 Passport 8250 Installation Guide R2.2 See “Passport 8250 front panel” (page 17) for an illustration of the hardwarecomponents. Figure 2Passport 8250 front panel Board modules The Passport 8250 device has a field-replaceable network board and up tothree field-replaceable DS...

18 Chapter 1 Passport 8250 241-5101-200 R2.2 Communication ports The communication ports, which are located on the network board, include aserial port, ethernet port, and redundant ATM uplink port. Serial port The serial port connects the Passport 8250 device to a local host using aRS-232 cable. Usi...

Chapter 1 Passport 8250 19 Passport 8250 Installation Guide R2.2 Passport 8250 software You do not have to order software for the Passport 8250. The Passport 8250comes preloaded with the operating system and the applications it needs.Base trunking software is included with the integrated trunk/contr...

21 Passport 8250 Installation Guide R2.2 Chapter 2Preparing for the hardware installation This section provides the following procedures for preparing for installing thePassport 8250 device: 1 “Selecting an installation site” (page 21) 2 “Unpacking the Passport 8250 shipment” (page 22) 3 “Taking inv...

22 Chapter 2 Preparing for the hardware installation 241-5101-200 R2.2 — Access is through the use of a special tool, or lock and key, or other means of security, and is controlled by the authority responsible forthe location. Unpacking the Passport 8250 shipment Move the Passport 8250 package to th...

24 Chapter 2 Preparing for the hardware installation 241-5101-200 R2.2 Getting the tools to mount the chassis in a rack To mount the chassis in a rack, you will need one or more of the followingtools: • 9.5 mm wide flat-bladed screwdriver for 19” or ETSI rack installation. • 10 mm A/F nut driver for...

25 Passport 8250 Installation Guide R2.2 Chapter 3Installing the Passport 8250 device This section provides the following procedures for installing the Passport8250 device: 1 “Mounting the chassis in a rack” (page 25). 2 “Connecting cables to the ports” (page 29). 3 “Connecting the dual power supply...

26 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 • Allow at least 2 inches of ventilation space on both sides of the device asillustrated in “Ventilation space” (page 26). • Do not block the air flow around the device with cables. For details, see“Securing the cables to the rack” (...

Chapter 3 Installing the Passport 8250 device 27 Passport 8250 Installation Guide R2.2 Figure 4Attaching mounting brackets to chassis Figure 5Installing the chassis on a 19” rack Secure mountingbrackets to the unitusing the fixingholes indicated Temporaryfixing forinstallationaid Allow a minimum of ...

28 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 Mounting the Passport 8250 device on a NEBS or ETSI rack 1 Locate the bracket mounting holes on each side of the chassis. 2 Attach the mounting brackets to each side of the chassis using a Pozidrivescrew driver. See “Attaching mounti...

Chapter 3 Installing the Passport 8250 device 29 Passport 8250 Installation Guide R2.2 Connecting cables to the ports You have to connect cables to the following ports: • DS-1/E1 ports. For details on connecting cables, see “Connecting theDS-1/E1 ports” (page 29). • Ethernet port. For details on con...

Chapter 3 Installing the Passport 8250 device 31 Passport 8250 Installation Guide R2.2 Connecting the ethernet port 1 Obtain the following equipment: • A regular RJ-45 ethernet cable with a male DB-8 connector and a 10Base-T ethernet drop for a connection to a work station. • A cross-connect RJ-45 e...

32 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 3 Connect the other end of the RJ-45 cable to a 10 Base-T ethernet drop orwork station. Connecting the serial port 1 Obtain the following equipment: • VT-100 terminal or a PC with terminal-emulation software • Null modem RS-232 cable...

Chapter 3 Installing the Passport 8250 device 33 Passport 8250 Installation Guide R2.2 Connecting the ATM uplink port 1 Obtain the following equipment: • Multi-mode fiber optic cables with SC connectors with a typical rangeof 0-2 km • Single-mode fiber optic cables with SC connectors with a typicalr...

34 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 Figure 7Dual power supply 1 Obtain the following equipment: • A -48 v DC power supply cable with 3W3-D connector for each powersupply module. • Antistatic protection, such as an antistatic glove. 2 If the power supply module is suppl...

Chapter 3 Installing the Passport 8250 device 35 Passport 8250 Installation Guide R2.2 The central contact is designated as the chassis ground. 4 Connect the -48v power supply cable with the male 3W3-D connector tothe female 3W3-D connector. Tighten the screws on the 3W3-D connector and verify that ...

36 Chapter 3 Installing the Passport 8250 device 241-5101-200 R2.2 Exit and secure all cables to the left as illustrated in “Cables left of chassis”(page 36) or underneath the chassis as illustrated in “Cables underneathchassis” (page 36). Figure 8Cables left of chassis Figure 9Cables underneath cha...

37 Passport 8250 Installation Guide R2.2 Chapter 4Configuring the Passport 8250 for operations This section provides the following procedures for configuring the Passport8250 device for the operations: 1 “Logging into the CLI” (page 37) 2 “Configuring the Passport 8250 device for remote access” (pag...

38 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 a. For each power supply module, turn the power supply breaker to ON. The LEDs on each power supply module is on. Text is displayed on the hyperterminal screen. 3 From the hyperterminal session, stop the Passport 8250 device...

Chapter 4 Configuring the Passport 8250 for operations 39 Passport 8250 Installation Guide R2.2 See “Boot command parameters” (page 39) for the boot parameters you needto configure. Viewing the boot parameters To display the existing boot parameters, Type the bootconfig commandwithout the [set] para...

40 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 4 For host inet, type the IP address of the remote host. 5 If the remote host is on a different network, type the IP address of thegateway node at the gateway inet prompt. 6 For user, type the FTP userid of the remote host. ...

Chapter 4 Configuring the Passport 8250 for operations 41 Passport 8250 Installation Guide R2.2 where [set] configures the clocking scheme for the Passport 8250 device. For details on the clockconfig parameters, see “Clockconfig commandparameters” (page 41). Table 4Clockconfig command parameters Par...

42 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 Setting the clocking scheme to External Primary 1 Display the clockconfig parameters: clockconfig [set] 2 For External Primary Board Number, enter a board number. 3 For External Primary Port Number, enter a port number. 4 Fo...

Chapter 4 Configuring the Passport 8250 for operations 43 Passport 8250 Installation Guide R2.2 [E1-1]: clockconfig set External Primary Board Number (0 - 3) = 0 2 External Primary Port Number (1 - 16) = 3 10 External Secondary Board Number = 0 External Secondary Port Number = 3 Admin Reference Cloc...

44 Chapter 4 Configuring the Passport 8250 for operations 241-5101-200 R2.2 clockconfig [set] 2 For External Primary Board Number, enter a board number. 3 For External Primary Port Number, enter a port number. 4 For External Secondary Board Number, enter a board number. 5 For External Secondary Port...

45 Passport 8250 Installation Guide R2.2 Appendix AReplacing hardware This section provides instructions on how to replace hardware components onthe Passport 8250 device. You can view the following procedures in thissection: • “Replacing a power supply module” (page 46) • “Replacing a board module” ...

46 Appendix A Replacing hardware 241-5101-200 R2.2 Replacing a power supply module The Passport 8250 device is powered by two power supply modules. If apower supply module stops operating, you need to immediately replace itwith a dummy power supply filler pack to ensure proper cooling and air flow.Y...

Appendix A Replacing hardware 47 Passport 8250 Installation Guide R2.2 4 Slide the power supply module or dummy power supply filler pack out ofthe slot. 5 Insert the new power supply module or dummy power supply filler packinto the empty power supply slot. 6 Using a screw driver, tighten the four se...

48 Appendix A Replacing hardware 241-5101-200 R2.2 Figure 11Board slots 1 For each power supply module, set the power supply breaker to off. 2 Flip the lock hatch at each end of the circuit board slot open. 3 Slide the network board or service board out of the circuit board slot. 4 Remove the new ne...

Appendix A Replacing hardware 49 Passport 8250 Installation Guide R2.2 Passport 8250 board guidelines Use caution when handling, storing, and transporting circuit boards. Followthese guidelines: • Do not stack or store boards without first replacing them in theirantistatic material and shipping mate...

50 Appendix A Replacing hardware 241-5101-200 R2.2 The fans continue to rotate for a few seconds. 4 Remove the new fan module from the package. 5 Insert the new fan module into the empty fan module slot. 6 Tighten the two securing screws on the fan module. 7 For each power supply module, turn the po...

52 Appendix B LEDs 241-5101-200 R2.2 Figure 12Passport 8250 LEDS 5 1 2 3 4 Fan module Network board Power supply 1 Power supply 2 Service boards 8 7 6 5

55 Passport 8250 Installation Guide R2.2 Appendix CStandards This section describes the standards the Passport 8250 device meets. You canview the following topics in this section: • “Product safety standards” (page 55) • “Electromagnetic compatibility standards” (page 55) • “Telecom standards” (page...

56 Appendix C Standards 241-5101-200 R2.2 — FCC Part 15, Class A (USA) — ICES-003, Class A (Canada) — EN 55022, Class A (Europe) • Immunity, ESD, EFT (EU) — EN50082-1 — EN300 386-2 — Bellcore GR-1089-CORE Telecom standards The Passport 8250 device meets the following telecom standards: • FCC Pt 68 (...

Appendix C Standards 57 Passport 8250 Installation Guide R2.2 Federal Communications Commission (FCC) The Passport 8250 device complies with Part 68 of the FCC rules. On the topof this equipment is a label that contains, among other information, the FCCregistration. If requested, this information mu...

58 Appendix C Standards 241-5101-200 R2.2 Before installing this equipment, users should ensure that it is permissible tobe connected to the facilities of the local telecommunications company. Theequipment must also be installed using an acceptable method of connection.The customer should be aware t...