Nortel 201i - Manuals - manualsarea.com

Standard 1.07 2 CallPilot Copyright © 2006 Nortel Networks. All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented with...

Page 4 - SONY is a trademark of Sony Corporation.; Information for Japan; Japan VCCI statement

Standard 1.07 4 CallPilot SONY is a trademark of Sony Corporation. SYBASE is a trademark of Sybase, Inc. TEAC is a trademark of TEAC Corporation. US ROBOTICS, the US ROBOTICS logo, and SPORTSTER are trademarks of US Robotics. WINZIP is a trademark of Nico Mark Computing, Inc. XEON is a trademark of ...

Page 5 - Publication history

201i Server Hardware Installation 5 Publication history November 2006 Standard 1.07 of 201i Server Hardware Installation is released for CallPilot 4.0 general availability. October 2006 Standard 1.06 of 201i Server Hardware Installation is released for CallPilot 4.0 general availability. October 200...

Page 6 - CallPilot Installation and

6 CallPilot Publication history Standard 1.07 September 2002 Standard 1.0 of CallPilot Installation and Configuration, Part 2: 201i Server Hardware Installation is released for CallPilot 2.0 general availability.

Page 9 - Task List

201i Server Hardware Installation 9 Task List To unpack the 201i server ............................................................... 41To prepare the 201i server for installation in a Meridian 1 switch ... 52To position the 201i server on the switch shelf ............................... 56To remo...

Page 11 - Contents; How to get help; Section A: Installing Option 11C cables

201i Server Hardware Installation 11 Contents 1 How to get help 13 2 About the 201i server 15 201i server description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Network connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 12 - Preparing peripheral devices

Contents Standard 1.07 12 CallPilot 6 Installing the 201i server in the Succession 1000 system 95 Succession 1000 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Removing the Media Gateway or Media Gateway Expansion cover . . . . 104Installing the 201i server. ....

Page 13 - C h a p t e r 1; Getting Help from the Nortel Web site; download software, documentation, and product bulletins; Getting Help over the phone from a Nortel Solutions Center

201i Server Hardware Installation 13 C h a p t e r 1 How to get help This section explains how to get help for Nortel products and services. Getting Help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: http://www.norte...

Page 14 - Getting Help through a Nortel distributor or reseller

How to get help Standard 1.07 14 CallPilot Outside North America, go to the following Web site to obtain the phone number for your region: http://www.nortel.com/callus Getting Help from a specialist by using an Express Routing Code To access some Nortel Technical Solutions Centers, you can use an Ex...

Page 15 - C h a p t e r 2; About the 201i server; In this chapter

201i Server Hardware Installation 15 C h a p t e r 2 About the 201i server In this chapter 201i server description 16 Network connectivity 24 Peripheral connectivity 31

Page 16 - Introduction; and Succession; RoHS compliance; The 201i server motherboard houses the interfaces needed:

About the 201i server Standard 1.07 16 CallPilot 201i server description Introduction The 201i server is a flexible multimedia telephony server designed to integrate with Nortel Meridian 1 * and Succession * 1000 products. The 201i server occupies two slots of a Meridian 1 shelf or Succession 1000 M...

Page 17 - ATTENTION

November 2006 About the 201i server 201i Server Hardware Installation 17 Two Ethernet controllers on the 201i server motherboard provide Ethernet capability. These controllers provide the network interfaces for both the embedded LAN (ELAN) and customer LAN (CLAN). The connections to the ELAN and CLA...

Page 18 - The following diagram shows the 201i server components:.

About the 201i server Standard 1.07 1 8 CallPilot The following diagram shows the 201i server components:. Heat sink Hard drive power cable Hard drive data cable Secondary backplane connector pin Secondary backplane connector 3.5-inch IDE hard drive Hard drive mounting bracket Software feature key(D...

Page 19 - Faceplate

November 2006 About the 201i server 201i Server Hardware Installation 19 Faceplate The following diagram shows the 201i server faceplate. The faceplate provides LEDs, MPC card slots, and connectors for peripheral devices: G10143 8 Lock latch Keyboard connector Mouse connector Infrared port (future u...

Page 20 - Faceplate feature; not

About the 201i server Standard 1.07 20 CallPilot The following table describes each faceplate feature: Faceplate feature Description Mouse connector The mouse connector is a standard PS/2 connector and is hot-pluggable. Lock latches Lock latches at the top and bottom of the faceplate secure the serv...

Page 21 - CallPilot 201i Server Maintenance

November 2006 About the 201i server 201i Server Hardware Installation 21 MPC card status LEDs (continued) On, then off: The MPC card has been successfully powered down. It is safe to remove the card. Note: For instructions on powering up or powering down the MPC card, see “Starting and stopping co...

Page 22 - Environmental specifications; Temperatures; Reset button

About the 201i server Standard 1.07 22 CallPilot Environmental specifications Temperatures Relative humidity Network and drive activity LEDs (labeled as E, C, I, and S) The E and C LEDs indicate the presence of network activity for both the ELAN and CLAN interfaces (respectively). When they are lit,...

Page 23 - Absolute RH

November 2006 About the 201i server 201i Server Hardware Installation 23 Absolute RH 20% to 80% RH (noncondensing) Long-term storage RH 5% to 95% RH [at –40 ° C (-40 ° F) to 70 ° C (158 ° F) respectively] (noncondensing)

Page 24 - Network connectivity; large systems, such as Option 51C

About the 201i server Standard 1.07 24 CallPilot Network connectivity Introduction This section shows how CallPilot and the Meridian 1 or Succession 1000 system are integrated into your network. It also describes what is required in the network for correct CallPilot operation. Sample network setup: ...

Page 26 - Sample network setup: Succession 1000

About the 201i server Standard 1.07 26 CallPilot Sample network setup: Succession 1000 The following diagram shows an example of how the 201i server can be integrated with the Succession 1000 system in your network: G101630 OptivityTelephony Manager PC W eb-enabled CallPilot administrative PC W eb-e...

Page 27 - Planning and Installation Guide; CallPilot CLAN and ELAN network; setup; The 201i server supports the following network protocols:

November 2006 About the 201i server 201i Server Hardware Installation 27 In the illustration on page 26, the telephony LAN (TLAN) provides IP connectivity between the Succession 1000 system and the i2004 Internet phonesets. The connection between the Call Server and Media Gateway can be point-to-poi...

Page 28 - Network requirements; Multi I/O cable description

About the 201i server Standard 1.07 2 8 CallPilot Network requirements Appropriate networking equipment must be available for both the CLAN and ELAN. The CLAN and ELAN must be properly configured for correct CallPilot operation. To ensure correct configuration, Nortel recommends that you consult a n...

Page 29 - Labels on the RJ-45 cables distinguish the CLAN and ELAN; Connector type

November 2006 About the 201i server 201i Server Hardware Installation 29 The following table identifies the purpose of each connector on the NTRH0912 1 multi I/O cable. Note: Labels on the RJ-45 cables distinguish the CLAN and ELAN connectors. 1.For customers in EUED countries: see Appendix A, “RoHS...

Page 31 - Peripheral connectivity; keyboard

November 2006 About the 201i server 201i Server Hardware Installation 31 Peripheral connectivity Introduction Peripheral equipment is attached to the 201i server on the server faceplate. Faceplate connections The following peripheral devices connect to the 201i server faceplate: monitor (SVGA) k...

Page 32 - SCSI connections; Supported peripheral devices

About the 201i server Standard 1.07 32 CallPilot MPC-8 card The MPC-8 card looks like a Type II PC card, and supports the multimedia telephony services on the 201i server. Four specially-designed card slots are available for the MPC-8. All are located on the 201i server faceplate. SCSI connections T...

Page 33 - The CD-ROM drive is not hot-pluggable. You must power off the; Since the hub is an external device, it requires an AC power source.; or

November 2006 About the 201i server 201i Server Hardware Installation 33 Note: The CD-ROM drive is not hot-pluggable. You must power off the server to connect or disconnect the drive. Tape drive (NTRH9038) An external SCSI tape drive is used to back up and restore data. The device connects to the se...

Page 34 - The mouse connector on the 201i faceplate is a PS/2 connector. If

About the 201i server Standard 1.07 34 CallPilot Note: The mouse connector on the 201i faceplate is a PS/2 connector. If you plan to use a USB mouse with USB-to-PS/2 converter, you must also use the Nortel-supplied 101 mm (4-in) PS/2 extension cable (A0855616). Without the extension cable, the monit...

Page 35 - C h a p t e r 3; Preparing for installation

201i Server Hardware Installation 35 C h a p t e r 3 Preparing for installation In this chapter Installation overview 36 Unpacking and inspecting the 201i server 41 Switch and network requirements 44

Page 36 - CallPilot Planning and Engineering Guide

Preparing for installation Standard 1.07 36 CallPilot Installation overview Introduction This section provides a high-level overview of the requirements and procedure for installing the 201i server. For a list of CallPilot documentation, see the document map on page 7. Before you begin Ensure that p...

Page 37 - Installation checklist; WARNING; CallPilot Installation and Configuration Task

November 2006 Preparing for installation 201i Server Hardware Installation 37 Installation checklist The following checklist identifies the steps required to install the 201i server and peripheral devices. For more details, see Chapter 8, “Connecting peripheral devices to the 201i server.” . WARNING...

Page 38 - Step

Preparing for installation Standard 1.07 3 8 CallPilot 2 Familiarize yourself with the “Switch and network requirements” on page 44 of this guide. ❒ 3 If you are installing the 201i server into a Meridian 1 tiered system, do the following: Change the location of the secondary backplane (DS30X) con...

Page 39 - Option 11C or Option 11C Mini (see page 72)

November 2006 Preparing for installation 201i Server Hardware Installation 39 6 Set the following: SCSI IDs on the CD-ROM and tape drives (see pages 126 and 128) DIP switches on the CD-ROM drive (see page 126) device termination on the CD-ROM and tape drives (see page 130) ❒ 7 Insert the 201i ...

Page 40 - Server Configuration

Preparing for installation Standard 1.07 40 CallPilot 9 Connect the 201i server and devices as follows: Connect the monitor, keyboard, and mouse to the 201i server faceplate (see page 142). ❒ Connect the CD-ROM and tape drives to the intermediate SCSI cable (see page 144). ❒ Connect the multi ...

Page 41 - Unpacking and inspecting the 201i server; This section describes how to:; To unpack the 201i server; CallPilot Installation and Configuration Task List

November 2006 Preparing for installation 201i Server Hardware Installation 41 Unpacking and inspecting the 201i server Introduction This section describes how to: unpack the 201i server and peripherals inspect the 201i server for damage It also describes what to do if you determine that the 201i...

Page 42 - To inspect the 201i server for shipping damage; Item

Preparing for installation Standard 1.07 42 CallPilot To inspect the 201i server for shipping damage Before proceeding with the installation, visually inspect the 201i server for any damage that might have occurred during shipping. Ensure also that the items in the following checklists are secure: W...

Page 43 - Review the “Switch and network requirements” on page 44.

November 2006 Preparing for installation 201i Server Hardware Installation 43 What’s next? Review the “Switch and network requirements” on page 44.

Page 44 - Switch and network requirements; Switch

Preparing for installation Standard 1.07 44 CallPilot Switch and network requirements Introduction The information in this section will help you plan your 201i server installation. Meridian 1 or Succession 1000 slot requirements The 201i server occupies two physical and electrical slots. You must in...

Page 45 - Meridian 1 I/O panel connections; One connection is for the multi I/O cable.; CLAN and ELAN network requirements; The 201i server cannot be installed in slots 0 or

November 2006 Preparing for installation 201i Server Hardware Installation 45 Meridian 1 I/O panel connections On large Meridian 1 systems (such as Option 51C), the 201i server requires two connections from the slots to the I/O panel on the rear of the switch, as follows: One connection is for the...

Page 46 - To install the 201i server in

Preparing for installation Standard 1.07 46 CallPilot If the LAN is to be networked with the 201i server, you need a network specialist to ensure proper configuration. What’s next? Install the 201i server in the Meridian 1 switch or Succession 1000 system. For instructions, see one of the following:...

Page 47 - C h a p t e r 4

201i Server Hardware Installation 47 C h a p t e r 4 Installing the 201i server in a large Meridian 1 system In this chapter Overview 4 8 Repositioning the secondary backplane connector 50 Installing the 201i server in the large Meridian 1 switch 56 Removing the backplane (tip and ring) cables 5 8 I...

Page 48 - Overview; Secondary backplane connector

Installing the 201i server in a large Meridian 1 system Standard 1.07 4 8 CallPilot Overview Introduction This section describes how to install the 201i server in a Meridian 1 switch. Meridian 1 I/O panel connections On the Meridian 1, the 201i server requires two connections from the slots to the I...

Page 49 - SCSI cables; CAUTION

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 49 Backplane (tip and ring) cable The backplane (tip and ring) cable supplied with the 201i server (NTRH3501) provides 100Base-T Ethernet CLAN operation. This cable offers more network throughput ...

Page 51 - Secondary backplane connector description; connector

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 51 Secondary backplane connector description The secondary backplane connector is attached to the backplane edge of the 201i server. It consists of the following items: connector screws pin ...

Page 52 - Required equipment

Installing the 201i server in a large Meridian 1 system Standard 1.07 52 CallPilot Required equipment To move the secondary backplane connector, you need a Phillips No. 1 screwdriver. A pair of needle-nosed pliers can also be helpful for removing the pin connector. To prepare the 201i server for ins...

Page 56 - To position the 201i server on the switch shelf

Installing the 201i server in a large Meridian 1 system Standard 1.07 56 CallPilot Installing the 201i server in the large Meridian 1 switch Introduction The 201i server occupies two slots. You can install the 201i server in slots 0 through 14. Ensure that both slots have electrical backplane connec...

Page 58 - NTRH1408 intermediate SCSI cable; Before you begin; the shelf, refer to the; DANGER

Installing the 201i server in a large Meridian 1 system Standard 1.07 5 8 CallPilot Removing the backplane (tip and ring) cables Introduction You must remove the Meridian 1 backplane (tip and ring) cables that are associated with the slots occupied by the 201i server so that you can install the foll...

Page 59 - To remove the backplane cables

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 59 To remove the backplane cables 1 Remove the I/O panel cover from the rear of the Meridian 1 switch. 2 Remove the protective plate from the rear of the Meridian 1 switch. 3 Remove the existing b...

Page 61 - Continue with “Installing the NTRH3501 backplane cable” on page 62.

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 61 The following diagram shows an example using slots 3 and 4: What’s next? Continue with “Installing the NTRH3501 backplane cable” on page 62. G101549 C B A

Page 62 - Installing the NTRH3501 backplane cable

Installing the 201i server in a large Meridian 1 system Standard 1.07 62 CallPilot Installing the NTRH3501 backplane cable Introduction You must connect the backplane (tip and ring) cable supplied with the 201i server (NTRH3501) for 100Base-T Ethernet CLAN operation. This cable offers more network t...

Page 63 - To install the NTRH3501 backplane cable

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 63 Before you begin Before you can install the NTRH3501 cable, you must remove the existing backplane cable from the back of the switch. See “Removing the backplane (tip and ring) cables” on page ...

Page 64 - Continue with “Installing the SCSI cables for Meridian 1” on page 65.

Installing the 201i server in a large Meridian 1 system Standard 1.07 64 CallPilot See the following diagram: What’s next? Continue with “Installing the SCSI cables for Meridian 1” on page 65. G101550 Backplane cableNTRH3501 Multi I/O cableNTRH0912 UP 1 UP 2 UP 3 A B C

Page 65 - Installing the SCSI cables for Meridian 1; You require the following cables:

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 65 Installing the SCSI cables for Meridian 1 Introduction Before you can connect a CD-ROM or tape drive to the 201i server, you must install the SCSI cables. The SCSI cables route the SCSI connect...

Page 66 - What the completed installation looks like

Installing the 201i server in a large Meridian 1 system Standard 1.07 66 CallPilot The connector on the intermediate SCSI cable that attaches to the 201i server faceplate is a low-profile right-angle connector. This allows the cable to be attached with the Meridian 1 cabinet cover on. NTRH1410 (fo...

Page 67 - Meridian 1

November 2006 Installing the 201i server in a large Meridian 1 system 201i Server Hardware Installation 67 In this diagram, the CD-ROM drive is the first device. The tape drive is the last device. Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide. If ...

Page 68 - To install the SCSI cables for Meridian 1

Installing the 201i server in a large Meridian 1 system Standard 1.07 6 8 CallPilot To install the SCSI cables for Meridian 1 1 Thread the SCSI connector end of the NTRH140 8 cable from the front of the Meridian 1 along the bottom of the shelf to either the left or the right access channel. 2 Leave ...

Page 71 - C h a p t e r 5; Section B: Installing Option 11C Mini cables

201i Server Hardware Installation 71 C h a p t e r 5 Installing the 201i server in an Option 11C or Option 11C Mini In this chapter Installing the 201i server in the Option 11C or Option 11C Mini switch 72 Section A: Installing Option 11C cables 77 Installing the intermediate SCSI cable for Option 1...

Page 72 - Slots 1 through 9

Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 72 CallPilot Installing the 201i server in the Option 11C or Option 11C Mini switch Introduction The 201i server occupies physical and electrical slots. The 201i server must be installed in two peripheral equipment slots as...

Page 75 - Continue with installing the cables. Refer to one of the following:

November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 75 What’s next? Continue with installing the cables. Refer to one of the following: Section A: “Installing Option 11C cables,” on page 77 Section B: “Installing Option 11C Mini cables,”...

Page 77 - Section A: Installing Option 11C; In this section

November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 77 Section A: Installing Option 11C cables In this section Installing the intermediate SCSI cable for Option 11C 7 8

Page 80 - Peripheral cabling

Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 8 0 CallPilot Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide. If you want to use a connection scenario that is not described in this guide, ensure that you use appropriate...

Page 81 - To install the cable

November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 8 1 To install the cable 1 Attach the bracket assembly and cable as follows: a. Below the card cage, temporarily remove the hardware that secures cable connections to the Option 11C. b. Tem...

Page 85 - Section B: Installing Option 11C Mini

November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 8 5 Section B: Installing Option 11C Mini cables In this section Installing the NTRH3502 SCSI cable for Option 11C Mini 8 6 Installing cables on the back of the Option 11C Mini cabinet 92

Page 86 - Option 11C and Option 11C Mini Expansion Guide

Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 8 6 CallPilot Installing the NTRH3502 SCSI cable for Option 11C Mini Introduction Before you can connect a CD-ROM or tape drive to the 201i server, you must install the NTRH3502 SCSI cable. The NTRH3502 SCSI cable routes th...

Page 87 - the SCSI device IDs and DIP switches.

November 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 8 7 Note: Alternate SCSI device connection scenarios are supported, but are not depicted in this guide. If you want to use a connection scenario that is not described in this guide, ensure ...

Page 88 - To install the NTRH3502 SCSI cable

Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 88 CallPilot To install the NTRH3502 SCSI cable 1 If your Option 11C Mini is equipped with a Fiber Routing Guide, temporarily remove it. Note: For detailed instructions, refer to the Option 11C and Option 11C Mini Expansion...

Page 90 - SCSI cable installation to accommodate the Fiber Routing Guide

Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 90 CallPilot SCSI cable installation to accommodate the Fiber Routing Guide 6 If required, reinstall the Fiber Routing Guide. Note: For detailed instructions, refer to the Option 11C and Option 11C Mini Expansion Guide (NTP...

Page 92 - Option 11C Mini power cord with two ferrites; To connect the cables

Installing the 201i server in an Option 11C or Option 11C Mini Standard 1.07 92 CallPilot Installing cables on the back of the Option 11C Mini cabinet Introduction The following items connect to the back of the Option 11C Mini cabinet: multi I/O cable (NTRH0912) Option 11C Mini power cord with t...

Page 95 - C h a p t e r 6

201i Server Hardware Installation 95 C h a p t e r 6 Installing the 201i server in the Succession 1000 system In this chapter Succession 1000 description 96 Removing the Media Gateway or Media Gateway Expansion cover 104 Installing the 201i server 107 Installing the NTRH3502 SCSI cable for Successio...

Page 96 - Succession 1000 description; Call Server; The Call Server provides telephony services and call processing.

Installing the 201i server in the Succession 1000 system Standard 1.07 96 CallPilot Succession 1000 description Introduction The Succession 1000 system is an IP PBX that provides telephony and data capabilities over an IP network. The Succession 1000 system consists of the following major components...

Page 97 - one AC power cord connector and On/Off switch; Media Gateway and Media Gateway Expansion; Card slots

November 2006 Installing the 201i server in the Succession 1000 system 201i Server Hardware Installation 97 one AC power cord connector and On/Off switch The following diagram shows the Call Server: Media Gateway and Media Gateway Expansion The Media Gateway and Media Gateway Expansion provide the...

Page 100 - Back panel connectors; Connector

Installing the 201i server in the Succession 1000 system Standard 1.07 100 CallPilot Back panel connectors The following table describes the connectors that are located on the back of each Media Gateway and Media Gateway Expansion, and how they relate to CallPilot: Media Gateway Expansion Media Gate...

Page 102 - Except for the back panel connectors, the Media Gateway Expansion; Administration software

Installing the 201i server in the Succession 1000 system Standard 1.07 102 CallPilot Note: Except for the back panel connectors, the Media Gateway Expansion is similar in external appearance to the Media Gateway. Succession 1000 software For the 201i server, the Succession 1000 system must be runnin...

Page 103 - Succession 1000 documentation; Succession 1000 Planning and Installation Guide

November 2006 Installing the 201i server in the Succession 1000 system 201i Server Hardware Installation 103 Succession 1000 documentation If you need to refer to the following Succession 1000 technical documents, they are stored on the Customer Documentation Library CD-ROM (NTLH80BA), provided with...

Page 106 - Continue with “Installing the 201i server” on page 107.

Installing the 201i server in the Succession 1000 system Standard 1.07 106 CallPilot 2 Remove the inside front cover plate as follows: a. Use a screwdriver to loosen each screw on the top of the inside front cover plate by three turns. b. Apply pressure and slide the inside front cover plate upward ...

Page 107 - Installing the 201i server; For more information about card slots, refer to the; Unit; Media Gateway

November 2006 Installing the 201i server in the Succession 1000 system 201i Server Hardware Installation 107 Installing the 201i server Introduction This section describes how to install the 201i server inside the Media Gateway or Media Gateway Expansion. Before you begin Determine which pair of con...

Page 111 - To install the NTRH3502 cable

November 2006 Installing the 201i server in the Succession 1000 system 201i Server Hardware Installation 111 Note: Alternate connection scenarios are supported, but are not depicted in this guide. If you want to use a connection scenario that is not described in this guide, ensure that you use appro...

Page 114 - To replace the inside front cover plate

Installing the 201i server in the Succession 1000 system Standard 1.07 114 CallPilot Replacing the Media Gateway or Media Gateway Expansion cover Introduction This section describes how to replace the front bezel and inside front cover plate on the Media Gateway or Media Gateway Expansion. To replac...

Page 116 - To replace the front bezel

Installing the 201i server in the Succession 1000 system Standard 1.07 116 CallPilot To replace the front bezel 1 Align the two posts and the locking tab on the rear of the front bezel with the slots on the inside front cover plate. 2 Push the bezel toward the Media Gateway or Media Gateway Expansio...

Page 117 - This cable establishes the connection to the modem, ELAN, and CLAN.

November 2006 Installing the 201i server in the Succession 1000 system 201i Server Hardware Installation 117 Connecting cables to the Succession 1000 system Introduction The following items are connected to the back of the Media Gateway or Media Gateway Expansion: multi I/O cable (NTRH0912) This c...

Page 121 - C h a p t e r 7

201i Server Hardware Installation 121 C h a p t e r 7 Preparing peripheral devices In this chapter Overview 122 Setting the modem DIP switches 124 Setting the CD-ROM drive SCSI ID and DIP switches 126 Setting the tape drive SCSI ID 12 8 Setting SCSI device termination 130

Page 122 - The modem is connected to the 201i server by the multi I/O cable.; Supported SCSI devices; of a tape drive to perform and store backups.

Preparing peripheral devices Standard 1.07 122 CallPilot Overview Introduction You can connect a modem and one or more SCSI devices to the 201i server. The modem is connected to the 201i server by the multi I/O cable. The SCSI devices are connected to the 201i server by the intermediate SCSI cable. ...

Page 123 - This is currently the only supported tape drive.; DIP switches, SCSI ID, and SCSI device termination settings; DIP switches on the modem and CD-ROM drive

November 2006 Preparing peripheral devices 201i Server Hardware Installation 123 tape drive (NTRH9038): Tandberg SLR5 tape drive Note: This is currently the only supported tape drive. DIP switches, SCSI ID, and SCSI device termination settings For correct operation with the 201i server, you must s...

Page 124 - Setting the modem DIP switches; Function

Preparing peripheral devices Standard 1.07 124 CallPilot Setting the modem DIP switches Introduction Set the modem DIP switches to their default settings. This section describes how to set the modem DIP switches if they have been changed from the default settings. To set the modem DIP switches Ensur...

Page 126 - The CD-ROM drive discussed in this section is the external SCSI; To set the CD-ROM drive SCSI ID

Preparing peripheral devices Standard 1.07 126 CallPilot Setting the CD-ROM drive SCSI ID and DIP switches Introduction This section describes how to set the CD-ROM drive SCSI ID and DIP switches. Note: The CD-ROM drive discussed in this section is the external SCSI CD-ROM drive (NTRH9105). To set t...

Page 127 - To set the CD-ROM drive DIP switches; DIP switch

November 2006 Preparing peripheral devices 201i Server Hardware Installation 127 To set the CD-ROM drive DIP switches Set the CD-ROM drive DIP switches as described in the following table: What’s next? If you are also installing a tape drive, set the tape drive SCSI ID (see page 128); otherwise, set...

Page 128 - Setting the tape drive SCSI ID; This section describes how to set the tape drive SCSI ID.; To set the tape drive SCSI ID; The diagram is an example of the key components.

Preparing peripheral devices Standard 1.07 12 8 CallPilot Setting the tape drive SCSI ID Introduction This section describes how to set the tape drive SCSI ID. Note: The tape drive discussed in this section is the Tandberg SLR5 tape drive (NTRH9038). This is currently the only supported tape drive. ...

Page 130 - Setting SCSI device termination

Preparing peripheral devices Standard 1.07 130 CallPilot Setting SCSI device termination Introduction If you want to connect SCSI devices in a daisy chain, the last device in the daisy chain must be terminated. This section describes how to terminate the SCSI devices. Supported daisy chain connectio...

Page 132 - Option 11C, Option 11C Mini; “Installing the intermediate SCSI cable for Option 11C” on page 78; SCSI device cabling for Option 11C or Option 11C Mini

Preparing peripheral devices Standard 1.07 132 CallPilot Option 11C, Option 11C Mini For more information about the cabling requirements, see one of the following: “Installing the intermediate SCSI cable for Option 11C” on page 78 “Installing the NTRH3502 SCSI cable for Option 11C Mini” on page ...

Page 133 - To set device termination; Terminate the SCSI devices as described in the following table:; IF you are connecting

November 2006 Preparing peripheral devices 201i Server Hardware Installation 133 Succession 1000 For more information about the cabling requirements, see “Installing the NTRH3502 SCSI cable for Succession 1000” on page 110. To set device termination Terminate the SCSI devices as described in the fol...

Page 134 - a tape drive only

Preparing peripheral devices Standard 1.07 134 CallPilot What’s next? Complete the 201i server installation in the switch. See Chapter 8, “Connecting peripheral devices to the 201i server.” a tape drive only do nothing. External termination is not required because the drive is already internally ter...

Page 135 - C h a p t e r 8

201i Server Hardware Installation 135 C h a p t e r 8 Connecting peripheral devices to the 201i server In this chapter Overview 136 Installing the MPCs 140 Installing the monitor, keyboard, and mouse 142 Connecting the CD-ROM and tape drives 144 Connecting the 201i server to the switch, ELAN, and CL...

Page 136 - The switch connector is a 50-pin amphenol connector.; Connecting peripheral devices; MPC cards

Connecting peripheral devices to the 201i server Standard 1.07 136 CallPilot Overview Introduction This section describes installing the 201i server in the switch, connecting peripheral devices, and starting the 201i server. Connecting the 201i server to the network The switch, ELAN, CLAN, and modem...

Page 138 - 01i server faceplate and peripheral device connectors

Connecting peripheral devices to the 201i server Standard 1.07 13 8 CallPilot 201i server faceplate and peripheral device connectors The following diagram identifies the peripheral device connectors and slots on the 201i server faceplate: G101444 Keyboard connector Mouse connector Monitor connector ...

Page 139 - Starting the 201i server; Set the DIP switches on the external fax modem. See page 124.

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 139 Starting the 201i server When you lock the 201i into position against the switch backplane, the server starts automatically. You can observe the startup process on both the monitor and the 201i serve...

Page 140 - Installing the MPCs; To install the MPCs

Connecting peripheral devices to the 201i server Standard 1.07 140 CallPilot Installing the MPCs Introduction Two MPCs are preinstalled at the factory. This section describes how to install additional cards, if required. Correct card insertion The MPC-8 card is keyed so that it fits only one way int...

Page 142 - observe the 201i server startup process.; Hardware requirement

Connecting peripheral devices to the 201i server Standard 1.07 142 CallPilot Installing the monitor, keyboard, and mouse Introduction You must connect the monitor, keyboard, and mouse to the 201i server so that you can: observe the 201i server startup process. run the Configuration Wizard. per...

Page 143 - To connect the monitor, keyboard, and mouse; Continue with “Connecting the CD-ROM and tape drives” on page 144.

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 143 PS/2 extension cable The following diagram shows the PS/2 extension cable connected between the 201i server and the USB mouse with USB-to-PS/2 converter. To connect the monitor, keyboard, and mouse 1...

Page 144 - Connecting the CD-ROM and tape drives; Set the SCSI ID and device termination settings as described in; For

Connecting peripheral devices to the 201i server Standard 1.07 144 CallPilot Connecting the CD-ROM and tape drives Introduction You can connect the CD-ROM, tape drive, or both to the intermediate SCSI cable that you installed earlier. Before you begin Before you can connect the CD-ROM or tape drive,...

Page 145 - Selecting the procedure for your switch; If you are connecting the SCSI devices to the Option 11C, go to page; IF you are working with; IF the first device is the THEN

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 145 Selecting the procedure for your switch To connect the CD-ROM and tape drives to the 201i server (Meridian 1) Note: If you are connecting the SCSI devices to the Option 11C, go to page 147. If you ar...

Page 147 - THEN

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 147 that is not described in this guide, ensure that you use appropriate cabling for each SCSI device. 5 Connect the power cord for each device. 6 Power up the devices. 7 Continue with “ W hat’s next?” o...

Page 153 - To establish the switch and network connections

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 153 Connecting the 201i server to the switch, ELAN, and CLAN Introduction The CLAN and ELAN connections are established by using the 201i server multi I/O cable. To establish the switch and network conne...

Page 155 - Continue with “Connecting the modem” on page 156.

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 155 Option 11C Mini or Succession 1000 to a screw on the back of the cabinet 3 Connect the connector on the multi I/O cable that is labeled as ELAN to the switch network hub. 4 If CLAN is required, con...

Page 156 - Connecting the modem; To connect the modem

Connecting peripheral devices to the 201i server Standard 1.07 156 CallPilot Connecting the modem Introduction You must connect the modem to the 201i server if: you want to administer the 201i server from a remote location. you need assistance from Nortel technical support. Required equipment To...

Page 158 - Continue with “Completing the installation” on page 159.

Connecting peripheral devices to the 201i server Standard 1.07 15 8 CallPilot 6 Power on the modem. Note: Ensure that the modem is receiving power by checking that at least one LED on its front panel is lit. 7 Place the modem in an area where it cannot be accidentally damaged or where people cannot ...

Page 159 - Completing the installation; Ensure that the switch in which the 201i is installed is powered on.

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 159 Completing the installation Introduction To complete the installation of the 201i server, lock the 201i into position. The server starts up automatically. To complete the installation and start the 2...

Page 161 - Proceed with the

November 2006 Connecting peripheral devices to the 201i server 201i Server Hardware Installation 161 6 Ensure that the operating system logon window appears on the monitor. If the logon window does not appear, refer to the CallPilot <server model> Server Maintenance and Diagnostics guide for y...

Page 163 - A p p e n d i x A; In this appendix

201i Server Hardware Installation 163 A p p e n d i x A RoHS part conversion table In this appendix RoHS part conversion table 164

Page 164 - Nortel is phasing

RoHS part conversion table Standard 1.07 164 CallPilot RoHS part conversion table This appendix provides a mapping of RoHS-compliant parts to the equivalent non-RoHS-compliant parts for the 201i server. Nortel is phasing in RoHS-compliant 201i servers in countries affected by the EUED (European Unio...

Page 165 - ersion table

November 2006 RoHS part conversion table 201i Server Hardware Installation 165 T a ble 1: RoHS part con v ersion table Ty p e RoHS par t de scription (Th e non-Ro HS pa rt de scri ption i s in clu ded bel ow in p a rentheses if it is different from the Ro HS pa rt d e scription ) RoHS P E C Code Non...

Page 169 - Index; Numerics

201i Server Hardware Installation 169 Index Numerics 201i server components, diagram 18 damaged, what to do 42 faceplate connections 31 description 20 diagram 19 , 138 inspecting 42 installation checklist 37 – 40 prerequisites 44 installing large Meridian 1 systems 56 Option 11C 72 Option 11C Mini 7...