Niles IR-KIT - Manuals - manualsarea.com

Page 2 - PLASMA PROOF IR REPEATER KIT; TABLE OF CONTENTS

IR-KIT PLASMA PROOF IR REPEATER KIT TABLE OF CONTENTS Features ............................................................................................................................1 Product Overview..................................................................................................

Page 4 - PRODUCT OVERVIEW

PRODUCT OVERVIEW 2 1 3 7 4 2 6 5 IR-CB2 IR-SMR IR Blocking Cover Infrared Transparent Housing 10 feet of 2-conductor 24-gauge connecting wire 3.5mm mono mini-plug Self-adhesive tape IR-E1 Infrared LED

Page 7 - Figure 1

5 INSTALLATION 1. Select an appropriate location for the IR-CB2. 2. Run all the necessary wiring to the IR-CB2. Label the wires for future reference. 3. Plug the supplied 12V DC power supply into the un-switched AC outlet. 4. Plug the 12V DC power supply connector into the IR-CB2 socket marked POWER...

Page 8 - INSTALLATION DIAGRAM

JobSite IR-E1 Emitters IR-SMR Receiver Home Theater Plasma Display 12V DC Power Supply (Not Supplied) plugged into the Switched Outlet Home Theater Receiver Satellite Receiver Cable TV Receiver DVD Player CD/Audio Player Zone 2 In-Wall Speaker Optional IR-FMR Receiver IR-CB2 INSTALLATION DIAGRAM 6

Page 9 - The presence of status voltage; Note: Status voltage takes priority over IR command.; Figure 2; Figure 3

7 Power Status You can send a Power Status signal to IR-SMRreceiver by connecting a 12V DC power supply fromthe switched AC power outlet of the preamp/receiverto the status input jack of your IR-CB2. Any 12V DCpower supply with a minimum of 100mA currentcapacity can be used. Hi/Low Emitter Output Sw...

Page 10 - OPERATION; All components can be operated: Test all of your; Additional IR Receivers

8 OPERATION Test your IR Repeater system by following threeprincipal guidelines: 1. All components can be operated: Test all of your remote controls for all of your equipment. 2. Operation is consistent: A good test is to repeatedly step from Pause to Play with your VCR,CD, DVD, or Tape player remot...

Page 12 - Optical Feedback Loop

10 Optical or ElectromagneticInterference Direct sunlight, reflections, neon signs and othersources of infrared light or television sets, lightdimming controls and other sources ofelectromagnetic fields can induce noise andinterference into your IR repeater system. Symptomscan include: flashback LED...

Page 14 - SPECIFICATIONS; IR Blocking Cover Dimensions

12 SPECIFICATIONS (CONTINUED) IR-E1 IR system: Works with practically all brands of IR remotecontrols IR transmitting: 4' (line of sight) Emitters mount directly to the IR window of acomponent Wiring requirements: 10' of 2-conductor 24-gauge wire with a 3.5mm plugis supplied Use 18-gauge for distanc...

Page 15 - LIMITED WARRANTY

13 LIMITED WARRANTY JobSite Systems (“JOBSITE”), a Niles Audio Corporationcompany, warrants its passive products (those not requiringAC or battery power) to the original purchaser to be free ofmanufacturing defects in material and workmanship for aperiod of ten years from date of purchase. JOBSITE w...

Page 16 - JobSite Systems

14 If the above conditions are met, the purchaser’s soleremedy shall be to return the product to JOBSITE, in whichcase JOBSITE will repair or replace, at its sole option, thedefective product without charge for parts or labor.JOBSITE will return the unit repaired or replaced underwarranty by shippin...

Page 20 - JOBSITE SYSTEMS

JOBSITE SYSTEMS 12331 S.W. 130 STREET, MIAMI, FLORIDA 33186 P 866.4JB.SITE (866.452.7483) – F 305.238.0185 WWW.JOBSITESYSTEMS.COM © 2005 JobSite Systems. All rights reserved. JobSite, Pure Custom and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logois a trademark of Nil...