Niles SVL-6 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; Introduction

Introduction The SVL-6 is a combination speaker selector and volume con-troller. It allows you to connect up to six pairs of speakers toyour stereo receiver or amplifier and adjust the volume ofeach pair independently. Additionally, you can choose to lis-ten to any one pair, any combination of pairs...

Page 3 - Features and Benefits; TECH

Features and Benefits The SVL-6 offers a number of improvements over otherspeaker selector/volume controllers: ● The SVL-6 uses 12 position volume controls which aresuperior to 10 position designs. You get a broader range ofadjustment — there are 10 steps of attenuation instead of8. Steps 11-6 atten...

Page 5 - Installation Considerations; Amplifier Impedance Load; IMPORTANT; DO NOT use the; TOOLS; Slotted Screwdriver

Installation Considerations SVL-6 Power Handling The SVL-6 is designed for use with a receiver or amplifier hav-ing a maximum power output of 100 watts per channel at 8ohms. Damage caused by the use of a higher-power receiveror amplifier will void the warranty. Consult your Niles dealer,or receiver/...

Page 6 - Type of Speaker Wire

The SVL-6 includes impedance correction circuitry whichprotects your receiver or amplifier from low impedanceloads. The circuitry assures that your receiver or amplifier willsee a safe operating load, even when all six speaker pairs areplaying at the same time. The actual impedance load the SVL-6 pr...

Page 7 - Wire size is

not fit into the connectors. Never use solid-core, aluminum,or "Romex" type wire with the SVL-6. When running speakerwires inside walls, most states and municipalities in the U.S.specify that you must use a special type of speaker wire.Usually, the requirement is that the wire that has a spe...

Page 8 - Figure 1; Using a

7 S P E A K E R S E L E C T I O N / V O L U M E C O N T R O L S Y S T E M Figure 1 Using a Tube Amplifier Tube Amplifier Niles SVL-6 150 150 SPEAKER 6 L + L - R - R + AMPLIFIER L + L - R - R + L + L - R - R + L + L - R - R + L + L - R - R + L + L - R - R + SPEAKER 5 SPEAKER 4 SPEAKER 3 SPEAKER 2 L +...

Page 10 - Installation; Figure 2

Installation 1. Select a convenient location for the SVL-6. 2. Run all the necessary wiring to the SVL-6. Label the wiresfor future reference. See (Figure 2). 9 S P E A K E R S E L E C T I O N / V O L U M E C O N T R O L S Y S T E M Niles SVL-6 Receiver Speaker Pair 6 Speaker Pair 5 Speaker Pair 4 S...

Page 11 - Figure 4; Installing the Connectors; Figure 3; Removing the Connectors

3. Make the connections to the SVL-6. The amplifier/speakerconnectors on the SVL-6 are removable. If you wish, you mayremove the SVL-6's connectors to facilitate installation [see(Figure 3)]. Strip 3/8" of insulation from the end of eachwire. Tightly twist the end of each wire until there are no...

Page 12 - Operation; Playing One Pair of Speakers At a Time

Operation There are two ways to use the SVL-6. You may play andadjust the volume of one pair of speakers at a time, or playmultiple pairs simultaneously. If you intend to play more than one pair of speakers at thesame time, you will need to become familiar with the oper-ation of the SVL-6's PROTECTI...

Page 13 - Make sure the amplifier or receiver power is OFF and

S P E A K E R S E L E C T I O N / V O L U M E C O N T R O L S Y S T E M 12 6. Using the appropriate volume control on the front ofthe SVL-6, adjust the volume of the speakers to the desiredlistening level. 7. You can turn off the speakers by turning the appropri-ate volume control on the SVL-6 fully...

Page 15 - Constant Protection Switch; Balancing Speaker Volume; SPECIFICATIONS

Constant Protection Switch The SVL-6 is equipped with a manual override for the protec-tion circuit that enables you to defeat the front panel protec-tion switch and maintain constant impedance protection. Thiswill safeguard your amplifier from being overdriven due toaccidental or improper use by an...

Niles SVL-6 - Manual

Table of Contents:

Summary

Other Niles Models