NetComm NPPOE1001 - Manuals

Page 2 - Contents

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 2 www.netcomm.com.au Contents Important Information ............................................................................................................................................... 3 What you should know about Power Over Ethernet (P...

Page 3 - Important Information; What you should know about Power Over Ethernet (PoE); PLEASE ENSURE THAT YOU COMPLETLY READ THE FOLLOWING

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 3 Important Information What you should know about Power Over Ethernet (PoE) Power-over-Ethernet (PoE) or "Active Ethernet" eliminates the need to run 240 Volt power toWireless Access Points and other devices on a wired...

Page 4 - Introduction; Package Contents; The package contains the following:

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 4 www.netcomm.com.au Introduction Thank you for purchasing NetComm’s Power-over-Ethernet Adapter Kit. Before you start installingthe Power-over-Ethernet Adapter Kit, verify the following parts are included in your package. Package Contents The pac...

Page 5 - Installation; The POE Injector; Figure 1; Object; Injector; PWR LED

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 5 Installation This chapter describes the function of the Power-over-Ethernet Adapter Kit and shows how to installit on your network. Basic knowledge of networking is assumed. Read this chapter before you proceed. The POE Injec...

Page 6 - The POE Splitter; Figure 2; Splitter

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 6 www.netcomm.com.au The POE Splitter PoE Splitters split data and power from the Cat5 Ethernet line. It will output Ethernet data to thedevice via the Etherent port and DC 5V/1.67A or 12V/1A power via the DC output cable. Figure 2 Splitter Object...

Page 7 - Connecting the Power-over-Ethernet Adapter Kit; Do NOT turn the power ON at this stage.; Turn the power on to the injector at the 240Volt Power Point.

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 7 Connecting the Power-over-Ethernet Adapter Kit The Power-over-Ethernet Adapter Kit does not need software configuration. To install it, simplycomplete the following steps. Figure 2.4 shows how the Power-over-Ethernet Adapter ...

Page 8 - Figure 4

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 8 www.netcomm.com.au Now you should see that power is provided to the device you have connected to the POE Splitter. Ifthere is no power, please refer to the Troubleshooting section in this guide. The following figure illustrates connection of an ...

Page 9 - Figure 5

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 9 The following figure illustrates the connection of a Network Camera using Power Over Ethernet. Figure 5 Please Note: The total distance from the NB1300+4 ADSL Modem/Router to the Network Camera (as used in this example) shoul...

Page 10 - Appendix A: Cable Connections; RJ-45 Ethernet Network Ports; Ethernet Type; Category 3 or better, UTP or STP

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 10 www.netcomm.com.au Appendix A: Cable Connections This cable information is provided for your reference only. Please ensure you only connect theappropriate cable into the correct socket on either this product or your computer. If you are unsure ...

Page 11 - Straight-Through Cabling; Wire

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 11 In a straight-through cable, wires 1,2,3,4,5,6,7 and 8 at one end of the cable are still wires 1~8 at theother end. In a crossover cable, the wires of 1,2,3,6 are reversed so that wire 1 become 3 at the otherend of the cable...

Page 12 - Appendix B: Troubleshooting; The LEDs do not light up.; Check that the power supply is properly connected.; The Injector LED does not light up.; You are using the correct DC power cable and it is plugged in.; What if I connect the wrong cable and connectors?

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 12 www.netcomm.com.au Appendix B: Troubleshooting The LEDs do not light up. Check that the power supply is properly connected. The Injector LED does not light up. First, refer to the installation instructions to ensure that you have connected the ...

Page 13 - Appendix C: Technical Specifications; Environmental Information

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 13 Appendix C: Technical Specifications Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3x, Protocol CSMA/CD Ports 1 * 10/100Mbps RJ-45 port (per unit) Connector RJ-45 Speed 10/100Mbps at half/full duplex Cable Type UTP/STP Categor...

Page 14 - Appendix D: Registering your NetComm Product; Contact Information; Customer Information

NetComm NPPOE1001 Power over Ethernet Kit YML720Rev1 14 www.netcomm.com.au Appendix D: Registering your NetComm Product All NetComm Limited (“NetComm”) products have a standard 12 month warranty from date ofpurchase against defects in manufacturing and that the products will operate in accordance wi...

Page 15 - Product Warranty; Limitations of Warranty

YML720 Rev1 NetComm NPPOE1001 Power over Ethernet Kit www.netcomm.com.au 15 Product Warranty The warranty is granted on the following conditions: 1. This warranty extends to the original purchaser (you) and is not transferable; 2. This warranty shall not apply to software programs, batteries, power ...