Multi-Tech Systems MTD-H5 - Manuals

PRODUCT OVERVIEW Programming LEDs Signal strength LEDs are pre-programmed. However, you can change the pre-programmed settings with theAT#GPIO command. For details, refer to the HSPA+ AT Command Reference Guide Power Draw Radio Average Peak Peak Current Time (sec) to Registered Power Total InRush To...

SAFETY NOTICES AND WARNINGS Safety Notices and Warnings General Safety The modem is designed for and intended to be used in fixed and mobile applications. Fixed means the device isphysically secured at one location and cannot be easily moved to another location. Mobile means the device isused in oth...

SAFETY NOTICES AND WARNINGS ne respecte pas cette consigne, le responsable peut voir son accès aux services cellulaires suspendu ouinterdit, peut être poursuivi en justice, ou les deux. ■ Éteignez votre appareil sans fil à proximité des pompes à essence ou de diesel avant de remplir le réservoirde v...

SAFETY NOTICES AND WARNINGS User Responsibility Respect all local regulations for operating your wireless device. Use the security features to block unauthorized useand theft. QuickCarrier TM USB-D MTD-H5 User Guide 11

GETTING STARTED Getting Started Getting Started Overview To use the MTD, do the following: 1. Insert the SIM Card. Refer to Installing a SIM Card . 2. Power up the device. Refer to Turning the Device On or Off. 3. Install device drivers. Use the Connection Manager or follow instructions in the USB D...

GETTING STARTED 3. Verify that the SIM card fits into the holder properly and replace the cover. Removing a SIM Card To remove a SIM card: Warning: If the device is connected to a computer or power supply, disconnect it. Inserting or removing a SIM card with the device powered may harm the SIM card ...

GETTING STARTED 2. Suspend ModemQuery. 3. Wait for Steps 1-2 to complete. 4. Verify that the modem has disconnected. 5. Issue AT#SHDN and wait for OK . Wait 30 seconds after the OK before unplugging or removing power. 6. Disconnect the device from the USB port. Device Phone Number Every device has a...

GETTING STARTED Troubleshooting If the connection drops and teh Main page shows a Keep-alive Feature , clear out the error by removing the numeric file names under this directory. C:\Users\tdg\AppData\Roaming\Multi-Tech Connection Manager Note: Replace " tdg " with your Windows username. Acc...

USING LINUX Using Linux Shell Commands Testing Serial Ports To test the serial ports created by the driver, type in a shell: # cat /dev/ttyACM0 &# echo –en "ATE0\r" > /dev/ttyACM03# echo –en "AT\r" > /dev/ttyACM0 Note: Sending ATE0 is required, to avoid issues in the termin...

BASIC OPERATIONS Basic Operations Interacting with Your Device Overview This section describes how to use AT commands to interact with your device. Using terminal software such asKermit, you can issue AT commands to communicate with and configure your modem. The AT commands let youestablish, read an...

BASIC OPERATIONS +CSQ: <rssi>,<ber> Where: <rssi> Received signal strength indication. 0 (-113) dBm or less 1 (-111) dBm 2-30 (-109) dBm - (-53) dBm / 2 dBm per step 31 (-51) dBm or greater 99 Not known or not detectable <ber> Bit error rate, in percent 0 Less than 0.2% 1 0.2...

BASIC OPERATIONS The device is registered. If the device returns: +CREG: 0,2 The device is in a network searching state. Verify that Device Detects a Valid SIM Card If your device uses a SIM card, use the query SIM status command to verify if the device detects the SIM card. Todo this, enter: AT#QSS...

BASIC OPERATIONS Enter: AT+CMGR=1 Example response: +CMGR: "REC UNREAD","+16155554562z`z","","13/09/05,13:39:40-20"How are you?OK Sending Text Messages To send a text message in text mode: 1. Put the device in text mode. Enter:AT+CMGF=1The device responds.OK 2. Enter ...

REGULATORY STATEMENTS Regulatory Statements 47 CFR Part 15 Regulation Class B Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter...

REGULATORY STATEMENTS Council Directive 2004/108/EC of 15 December 2004 on the approximation of the laws of Member Statesrelating to electromagnetic compatibility;andCouncil Directive 2006/95/EC of 12 December 2006 on the harmonization of the laws of Member Statesrelating to electrical equipment des...

ENVIRONMENTAL NOTICES Environmental Notices Waste Electrical and Electronic Equipment Statement WEEE Directive The WEEE Directive places an obligation on EU-based manufacturers, distributors, retailers, and importers to take-back electronics products at the end of their useful life. A sister directi...

ENVIRONMENTAL NOTICES Restriction of the Use of Hazardous Substances (RoHS) Multi-Tech Systems, Inc Certificate of Compliance 2011/65/EU Multi-Tech Systems confirms that its embedded products comply with the chemical concentration limitations setforth in the directive 2011/65/EU of the European Parl...

ENVIRONMENTAL NOTICES REACH Statement Registration of Substances After careful review of the legislation and specifically the definition of an “article” as defined in EC Regulation1907/2006, Title II, Chapter 1, Article 7.1(a)(b), it is our current view Multi-Tech Systems, Inc. products would becons...

ENVIRONMENTAL NOTICES Information on HS/TS Substances According to Chinese Standards In accordance with China's Administrative Measures on the Control of Pollution Caused by Electronic InformationProducts (EIP) # 39, also known as China RoHS, the following information is provided regarding the names...

INDEX Index A I account activation.........................................................15 Industry Canada activation.......................................................................14 Class B .....................................................................24 cellular devices.............