Mitsubishi Electric PAC-YG63MCA - Manuals

Page 2 - Safety Precautions; Warning; WARNING

1 • Thoroughly read the following safety precautions before use.• Hazards that can occur from incorrect handling are classified by the symbols below: • After reading this manual, keep this manual for future reference. When the device is reinstalled or repaired, give this manual to those who provide ...

Page 3 - • The following parts should be included in your shipment:; Usage; Input

2 The AI controller measures temperature and humidity; it also has an alarm capability if the measurement data exceeds defined setpoints. Historical measurement data can be displayed via only the G(B)-50A Web browser and TG-2000A. Temperature and humidity cannot be displayed on the G-50A LCD.Further...

Page 4 - Example of System Configuration; LAN; (1) Channel 1 temperature or humidity sensor input

3 4-2. External Dimensions [ 24 VDC Power Supply] N623 Al controller PAC-YG63MCA MODEL SERVICE REF. PAC-INPUTWEIGHTSERIAL No. MADE IN JAPAN YG60MCA-J VOLTAGE DC24V;0.2A 0.6 kg / 1 / 3 8 lb Al controller PAC-YG63MCA [ Output LEDs ] Alarm Alarm Ch2 Ch1 [ OUTPUT ] Non-voltage Contact Output Alarm Alarm...

Page 5 - Prepare the following parts to install this device.; Installation

4 6-1. Parts Purchased Separately Prepare the following parts to install this device. [Parts to be Purchased Separately] [Commercially available parts] 6 Installation Required Part Specification Unit fixing screws M4 screw × 4 (* M4: ISO metric screw thread) Power supply for this device Commercially...

Page 6 - Note: Two hooks are located on the upper section of the cover.

5 6-2. Installation Instructions The AI controller PAC-YG63MCA does not have a waterproof structure. Be sure to install the AI controller inside a control panel that is located indoors. Prepare a control panel capable of storing this device such as the one shown in the figure. (Install the device in...

Page 7 - Diagram Image (Installed within a Control Panel); * The wiring in the diagram has been simplified.; Wiring Instructions

6 (3) Refer to "7. Wiring Instructions" and connect the wires for the power line, M-NET transmission line, output signal lines, and sensor input signal lines. 7-1. Terminal Diagram PAC-SC50KUA M-NET N FG L -V +V Diagram Image (Installed within a Control Panel) * The wiring in the diagram has...

Page 8 - Tightening torque for terminal screws: 1 N·m; * Only the M-NET circuitry of this device receives the power from the

7 7-2. Connecting the Power and M-NET Transmission Lines S FG M-NET S / B / A (M1) (M2) U U R V+/V-/FG CN02 A/B/S Tightening torque for terminal screws: 1 N·m Connect the M-NET transmission line of this device to a power supply unit (PAC-SC50KUA) for the M-NET transmission line or an outdoor unit (e...

Page 10 - Tightening torque for terminal screws: 1 N·m.

9 7-4. Connecting Alarm Setpoint Outputs The maximum wire length is 100 m. However, since the use of long wires makes the device susceptible to noise, using wires no more than 10 m long is recommended.To use these, various settings need to be configured. Refer to "8. Initial Settings". (Non-...

Page 11 - Initial Settings

10 After completing the procedures described in "6. Installation" and "7. Wiring Instructions", set the initial settings in accordance with the procedure described below. (1) M-NET address settings (2) Use the dip switches to select functions. Select the function required for each in...

Page 13 - Dip Switch Functions

12 Set the dip switches for function selection according to the system to be used.At factory default, the SW01, SW02, SW03, SW08, and SW09 dipswitches are all set to OFF; the SW11 and SW12 dipswitches are both set to ON, and the M-NET address is set to 01.Be sure to turn off the power before changin...

Page 15 - Use the following procedure to confirm operation of the system.; System Operation Test

14 Use the following procedure to confirm operation of the system. (1) Configure the settings of this device and the system controller while referring to "8. Initial Settings".(2) Confirm whether the measurement values of channel 1 and channel 2 are displayed on the system controller properl...

Page 16 - This product is designed and intended for use in the residential,

WT04975X02 Printed in Japan This product is designed and intended for use in the residential, commercial and light-industrial environment. This product at hand is based on the following EU regulations: • Low Voltage Directive 2006/95/EC• Electromagnetic Compatibility Directive 2004/108/EC NOTE:This ...