Mitsubishi Electric DIS710E - Manuals

Mitsubishi Electric DIS710E – Manual in PDF format online.

Manuals:

Manual

Manual Mitsubishi Electric DIS710E

Summary

Page 2 - Page; This system is composed by the following components.; CONTENTS; Printer

2 Page 1 SAFETY PRECAUTIONS ......................................................................................... 3 - 5 2 UNPACKING ................................................................................................................... 6 3 PRINTER SETUP .................................

Page 3 - SAFETY PRECAUTIONS; PROTECTIVE MEASURES

3 1. SAFETY PRECAUTIONS In the interest of safety, please observe the following precautions: POWER REQUIREMENT This system is designed for operation on 220V-240V, 50Hz AC. Never connect to any outlet or power supplyhaving a different voltage or frequency. WARNNG: THIS APPARATUS MUST BE EARTHED.AVERT...

Page 4 - Use the cables provided; INSTALLATION LOCATIONS; The operating ambient temperature range is 5; FOR LONG OPERATING LIFE

4 BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury.Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit. CONNECTION CABLES Use the cables provided INSTALLATION LOCATIONS MA...

Page 5 - OTHER CAUTIONS

5 CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime causefor damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from theconnected devices. CONNECTING DEVICES Read thoroughly "Op...

Page 7 - REMOVING SCREW AND CUSHION; REMOVING SCREW; Protective cushion; Set the removed screw to the hole on the rear panel to keep.; REMOVING PROTECTIVE CUSHION; Press the OPEN button on the front panel.; INSTALLING PRINT PAPER AND INK SHEET; INSTALLATION PROCEDURE OF PRINT PAPER

7 3. PRINTER SETUP Transport screw S-VIDEO REMOTE AC LINE VIDEO 1 2 Stored position REMOVING SCREW AND CUSHION See CP710E operation manual for details. 2 2 2 2 2 REMOVING SCREW 1 1 1 1 1 Remove the screw at the bottom of printing unit with ascrewdriver or coin. Protective cushion 1 Before printing a...

Page 8 - Right side; INCORRECT

8 2 2 2 2 2 Insert the print paper in the position as shown right. Place the gear to the right side.Set the paper roll first on the right side paper holder.Then, set the paper roll on the left side paper holder. Print paper Holder Install Holder Print paper Right side Left side 3 3 3 3 3 Insert the ...

Page 9 - INSTALLING THE INK SHEET; Put the coloured roller of the ink sheet to the ink cassette.; On the; INSTALLING THE INK CASSEETTE; Eliminate any slack of the ink sheet.; SET THE PRINTING UNIT; Push the printing unit until it is locked into place.

9 White roller A B C E Coloured roller INSTALLING THE INK SHEET Install the ink cassette with the ink sheet rolls before inserting theink cassette into the printer. 1 1 1 1 1 Put the coloured roller of the ink sheet to the ink cassette. A A A A A B B B B B 2 2 2 2 2 Put the thin stick of white rolle...

Page 10 - Make sure to turn off each device when connecting.; CABLE CONNECTION; To AC LINE

10 S-VIDEO REMOTE AC LINE VIDEO 1 2 4. CONNECTION Connect the components as follows.(example) Make sure to turn off each device when connecting. If you wish to fix the connection box to the printer, set them first before connecting with cables. CABLE CONNECTION To AC LINE To VIDEOOUT Transport screw...

Page 11 - There are two ways to set connection box.; SET UP CONNECTION BOX; FIXING TO THE PRINTER; Loosen three screws on the back of the printer.; PUTTING ON THE PRINTER

11 There are two ways to set connection box. SET UP CONNECTION BOX FIXING TO THE PRINTER 1 1 1 1 1 Loosen three screws on the back of the printer. 2 2 2 2 2 Catch the hooks of the connection box on each screws onthe printer. 3 3 3 3 3 Fix the three screws and the transport screw. PUTTING ON THE PRIN...

Page 12 - You can take a picture twice, and choose the better one.; Set the face in the circle on the LCD.; The first image is memorized in the camera.; Guide sheet; TAKING THE FIRST PICTURE

12 You can take a picture twice, and choose the better one. 1 1 1 1 1 Turn on the power of this system.Make sure to turn on the power of the connection box first.Then, turn on the power of the camera and the printer. 2 2 2 2 2 Attach a guide sheet with a circle on the LCD.Guide sheet A : for use in ...

Page 13 - Press MEM button to transfer the image to the printer.; The image is memorized in the printer.; Press SHOT button to display the source image.; The second image is memorized in the camera.; nd image; When printing only one image (not multiple picture), skip the step

13 8 8 8 8 8 Press MEM button to transfer the image to the printer. The image is memorized in the printer. 9 9 9 9 9 Press SHOT button to display the source image. A A A A A Press SHOT button again. The second image is memorized in the camera. B B B B B Select the image to be printed.Press C/P butto...

Page 14 - CAMERA ADJUSTMENT; For Iris setting, see the table shown right.; Press SHOT button to take a picture.; IRIS adjustment mode is selected.; Press UP or DOWN button to select MANUAL.; SHOT

14 6. PICTURE QUALITY ADJUSTMENT ADJUSTING PICTURE QUALITY To adjust the image source first is the key to get maximumpicture quality. 2 2 2 2 2 CAMERA ADJUSTMENT Always adjust the camera setting first. Only after you are surethat the camera is providing the best picture quality and colourbalance, ad...

Page 15 - camera; ADJUSTING THE COLOUR OF IMAGE (WHITE BALANCE); NOTE; White balance adjustment mode is selected.; Press UP or DOWN button to select LOCK.

15 7 7 7 7 7 Press SHOT button to take a picture.Check the brightness of image.If the brightness is not improved, repeat the steps 2 to 6 to get the best setting. camera a piece ofwhite paper actual distance of a personwho is taking a picture 2 2 2 2 2 ADJUSTING THE COLOUR OF IMAGE (WHITE BALANCE) D...

Page 16 - Press ZOOM button to finish the white balance setting menu.; FINE-ADJUSTING OF COLOUR; Press; or

16 6 6 6 6 6 Press ZOOM button to finish the white balance setting menu. 2 2 2 2 2 FINE-ADJUSTING OF COLOUR When more colour adjustment is necessary after adjusting whitebalance, use a remote control of the printer. 1 1 1 1 1 Connect the remote control to the printer or the camera.If the printer is ...

Page 17 - FEATURES AND FUNCTIONS; Press to take a picture.

17 7. FEATURES AND FUNCTIONS DOWN UP SHOT MEM PRINT C/P 1/2/3 B/W 1/2/3 IRIS WB MENU ZOOM SET CAMERA (FRONT) CAMERA (REAR) 3 3 3 3 3 2 2 2 2 2 1 1 1 1 1 6 6 6 6 6 5 5 5 5 5 4 4 4 4 4 C C C C C B B B B B A A A A A 1 1 1 1 1 9 9 9 9 9 8 8 8 8 8 7 7 7 7 7 6 6 6 6 6 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 2 2 2 2...

Page 19 - CHANGING SETTINGS

19 8. ADVANCED SETTING You can print 1, 2, 4, 6 and 16-image on a sheet. To make 1and 16-image print, change the setting as follows. 2 2 2 2 2 PRINTING 16- OR ONE-IMAGE ON A SHEET Use the remote control of the printer to print 16-image ona sheet. 1 1 1 1 1 Select the PRG. No. to be changed with the ...

Page 20 - SELECTING AUTO/MANUAL FOCUS; Press MENU button on the camera.

20 2 2 2 2 2 LOCK FUNCTION To avoid changing the setting of the camera, locking thecamera setting is recommended.When locked, the switch is on the right side and “L” isshown on red.When unlocked, the switch is on the left side and “U” isshown on green.Please see the figure on the right. 2 2 2 2 2 CH...

Page 21 - THE BEST CONDITION FOR THIS SYSTEM; EFFECT OF BACK FLASH; • The back flash reduces the shadow behind the subject.

21 THE BEST CONDITION FOR THIS SYSTEM OPEN MEMORY PRINT MONITOR ALARM SHEET PAPER S-VIDEO REMOTE POWER 2 2 2 2 2 EFFECT OF BACK FLASH • The back flash reduces the shadow behind the subject. 0.3m 0.3m 1.5m to 2m 2m Without back flash With back flash

Page 22 - BEFORE CALLING FOR SERVICE; THE RATIO OF FACE SIZES

22 9. TROUBLESHOOTING BEFORE CALLING FOR SERVICE Use the following troubleshooting chart to resolve any apparent defect in operation. If you areunable to resolve the problem, unplug the power cord and contact your dealer. No power • Is the power cord plug disconnected from the outlet? Connect the po...

Page 24 - Name of Importers; 5, Boulevard des Bouvets - 92741 NANTERRE cedex; MITSUBISHI ELECTRIC CORPORATION

Made from recycled paper IDSYS-F1 PRINTED IN JAPAN Name of Importers Mitsubishi Electric Europe B.V. Benelux Branch Nijverheidsweg 23 A, 3641 RP. Postbus 222, 3640 AE Mijdrecht Phone 02972-82461 FAX 02972-83936 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX...