Milan Technology MIL-L800i - Manuals

Page 3 - Table of Contents

Table of Contents 1. Introduction ............................................................................................................. 1 Features .................................................................................................................... 1 Package Contents ............

Page 4 - Introduction; Features

1 1. Introduction Thank you for purchasing MiLAN Technology’s Em Powered TM Series 8-port Power over Ethernet Injector Hub. Power-over-Ethernet (PoE) eliminates the need to run 110/220 VAC power to other devices on a wired LAN. Using Power-over-Ethernet, system installers need to run only a single C...

Page 5 - Package Contents

2 Auto detect PD and classification of power consumption level Supports manual control of port power detection and classification Support automatic system calibration Support Auto MDI/MDI-X depends on the uplink switch port Centralized power distribution for PoE powered Device (PD) High ...

Page 6 - Hardware Description; Physical Dimensions; Front Panel

3 2. Hardware Description This Section describes the hardware of the 8 port Power over Ethernet Hub, and gives a physical and functional overview. Physical Dimensions The MIL-L800i PoE Injector Hub’s physical dimension is: 440mm x 224mm x 44mm (Lx W x H) Front Panel The Front Panel of the MIL-L800i ...

Page 7 - LED Indicators; Rear Panel

4 LED Indicators The LED Indicators gives real-time information of systematic operation status. The following table provides descriptions of LED status and their meaning. Figure 2-2. LED indicators LED Status Color Description On Green Power is transmitting to the device Power Forwarding Off -- Powe...

Page 8 - Power On

5 Figure 2-3 Rear panel of the 8 port Power over Ethernet Hub Power On Connect the power cord to the power socket on the rear panel of the Switch. The other side of power cord connects to the power outlet. The internal power supply of the Switch works with voltage range of AC in the 100-240VAC, freq...

Page 10 - Software Utility Installation

7 3. Software Utility Installation Berfore you start to remote configuring PD, please intsall the software utility. Through the software utility, you can easily to controll the PD that connect with PoE and view the PD parameter informations. The software utility provides GUI interface and user can e...

Page 13 - GUI Management; Connecting to PoE

10 4. GUI Management Connecting to PoE Connecting the PoE with PC through the console port. Then, connect the PD (Powered Device) to the port of PoE. Run the software utility and select the COM port form Serial Link Setup function. You will see the main utility interface as figure 4-1. Figure 4-1. T...

Page 15 - System Information

12 System Information Chip Version: display the system chipset version and revision information. Firmware Version: display the system firmware version. Utility Version: display the system utility version Total Port Power (W): total of all the port power that the system provided to PD. Figure...

Page 16 - Device Setting

13 Device Setting Enable Auto-Refresh: It allows the system auto refresh the system parameters. The system auto refresh in every 2 seconds. Load from Device : To get the last configuration value from device to the system utility. Save to Device : When you have configured the System Setup &...

Page 17 - Port Specific Control

14 Port Specific Control Port Enable: enabling the port. This function is co-responding with “Master Enable” function. Bypass Detection: bypass the detection function. Normally the system will try to detect the 25k Ω resistor in an 802.3af compliant PD device. If the PD doesn’t follow by IEEE 80...

Page 20 - Parametric Information

17 Parametric Information Discovery R (ohms): display resistance value. Port Current (mA): display current value. Port Voltage (V): display voltage value. Port Power (W): display watt value. Class Current (mA): display class current value. When you enable the “Bypass classification” functi...

Page 21 - Technical Specification

18 5. Technical Specification Standards IEEE802.3af Power over Ethernet IEEE802.3 10Base-T, IEEE 802.3u 100Base-TX Connector Data in: 8 x RJ-45, Data pin 1,2,3,6 Data and power out: 8 x RJ-45. Data pin 1,2,3,6 Power pin (V+): 4,5, Power pin (V-): 7,8 Power out put Per port DC 48V@350mA (Maximum), Pe...

Page 23 - Appendix; Console Port Pin Assignments

20 6. Appendix Console Port Pin Assignments The female DB-9 serial port on the POE hub front panel is used to connect to the switch for out-of-band console configuration. The web interface configuration program can be accessed from PC running the system utility program. The pin assignments used to c...