Milan Technology CCSF30XX-100 - Manual
Milan Technology CCSF30XX-100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Set the Hardware/Software Jumper; Installation; Set the Configuration Switches
- Page 3 – PointSystemTM; Set the Loop-Back Switch; Install the Coax Cable
- Page 4 – Operation; SDC; SNMP; Power the Media Converter; Cable Specifications; Coax Cable
- Page 5 – Technical Specifications; Troubleshooting; YES
- Page 7 – Compliance Information; FCC Regulations
*Typical maximum cable distance. Actual
distance is dependent upon the physical
characteristics of the network.
Part Number
Port One -
Copper
Port Two -
Duplex Fiber-Optic
CCSCF3011-100
75 ohm coax (BNC)
ST, 1300 nm multimode
2 km (1.2 miles)*
CCSCF3013-100
75 ohm coax (BNC)
SC, 1300 nm multimode
2 km (1.2 miles)*
CCSCF3014-100
75 ohm coax (BNC)
SC, 1310 nm single mode
20 km (12.4 miles)*
CCSCF3015-100
75 ohm coax (BNC)
SC, 1310 nm single mode
40 km (24.8 miles)*
CCSCF3016-100
75 ohm coax (BNC)
SC, 1310 nm single mode
60 km (37.3 miles)*
CCSCF3017-100
75 ohm coax (BNC)
SC, 1550 nm single mode
80 km (49.7 miles)*
CCSCF3018-100
75 ohm coax (BNC)
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
CCSCF3019-100
75 ohm coax (BNC)
LC, 1310 nm single mode
20 km (12.4 miles)*
User’s Guide
CCSCF30xx-10x
Slide-in-Module Media Converter
•
DS3 or T3 / E3
•
Coax (BNC) to Fiber
Transition Networks CCSCF30xx-10x series media
converters encode and decode
DS3
or
E3
coax
copper signals over fiber optic cable to extend the
distance and transmission reliability of high-speed
DS3
or
E3
data traffic. The CCSCF30xx-10x,
which is designed to be installed in a Transition
Networks
PointSystem™
chassis, also connects
remote locations via
T3/E3
cable.
NOTE:
The
SCSCF30xx-10x
model is the stand-alone version of the media
converter. For more information, see the SCSCF30xx-10x user’s guide on-line at
www.transition.com.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .6
Cable Specifications . . . . . . . . . . .7
Technical Specifications . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . .9
Compliance Information . . . . . . .12
CCSCF3029-100 **
75 ohm coax (BNC)
SC, 1310 nm (TX)/1550 nm (RX)
single mode, 20 km (12.4 miles)*
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 CCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 * Typical maximum cable distance. Actual distance is dependent upon thephysical characteristics of the network. (TX) = transmit (RX) = receive ** CCSCF3029 -100 and - 101 are intended to be installed in the...
4 CCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Install the Slide-In-Module CAUTION: Wear a grounding device and observe electrostatic discharge p r e c a u t i o n s w h e n i n s t a l l i n g t h e C C S C F 3 0 x x - 1 0 x s l i d e - i n - m o d u l...
CCSCF30xx-11x 6 Operation After installation, the media converter should function withoutoperator intervention. Use the status LEDs to monitor the mediaconverter operation in the network. SDC Green on The coax link is up. Green flashing The coax link is in loop-back mode. Yellow on AIS (Alarm Indica...
