Miele PDR 910 [G] - Manuals

Contents 5 Installation ..................................................................................................................................... 70 Installation locations .......................................................................................................................

Caring for the environment 6 Disposal of the packing material The packaging is designed to protect the appliance from damage dur-ing transportation. The packaging materials used are selected frommaterials which are environmentally friendly for disposal and shouldbe recycled.Recycling the packaging r...

Warning and Safety instructions 7  It is essential to read these instructions. This tumble dryer complies with all current local and national safety requirements. How-ever, inappropriate use can lead to personal injury and damage to property.Read the operating instructions carefully before using th...

Warning and Safety instructions 8 Installation site Gas-heated tumble dryers must not be operated in a room where cleaning machines oper- ate with solvents containing perchloroethylene or CFCs. During combustion, any vapoursthat are emitted will break down into hydrochloric acid, leading to conseque...

Warning and Safety instructions 9  Any uses other than those listed above are prohibited. The manufacturer accepts no liab- ility in such cases. Foreseeable misuse  Do not make any alterations to the tumble dryer, unless authorised to do so by Miele.  Do not lean on the tumble-dryer door. Otherwi...

Warning and Safety instructions 11  The vent ducting must never be installed in any of the following flues or shafts: - Chimneys or smokestacks that are in use.- Shafts that are used to ventilate installation rooms with fireplaces.- Flues that are used by third parties. Smoke or exhaust gas that is...

Warning and Safety instructions 12  Keep the room where the tumble dryer is located free from dust and fluff. If the air that is taken into the machine contains dirt particles, this can cause blockages. A fault may thenoccur and there is a risk of fire.  Never operate the tumble dryer without the ...

Warning and Safety instructions 13  For tumble dryers with stainless steel surfaces: The stainless steel surfaces must not come into contact with liquid cleaning and disinfect-ing agents which contain chlorine or sodium hypochlorite. These agents can have a corros-ive effect on stainless steel.Aggr...

Description of the machine 14 PDR 910 (gas-heated) 1 2 3 4 6 5 7 8 9 10 11 a Control panel with touch display b Door c Fluff filter flap d 4 height-adjustable screw feet e Electrical connection f Communication module slot g Intake vents for drying air h Gas connection 1/2" acc. to ISO 7-1 i Exha...

Operating the tumble dryer 15 Control panel a    Language sensor control For selecting the current user languageAt the end of the programme, the language is automatically reset to the language set atthe supervisor level. b Back sensor control    Takes you back one level in a menu. c Touch display ...

Operating the tumble dryer 16 Sensor controls and touch display with sensor controls The sensor controls   ,  and Start/Stop and the sensor controls in the display re- spond to finger tip contact. Every touch of a sensor control is confirmed with an audiblekeypad tone. You can adjust the volume of...

Operating the tumble dryer 17 The orange scroll bar in the bottom display area shows that there are further options tochoose from.  To select the required drying programme, touch the programme name with your finger. The display will now change to the standard menu for that programme. “Extras” menu ...

Operating the tumble dryer 18 12:00 3 4 2 1 5 6 7  8 0 9 Clock display  OK  To enter the numerical value, touch the numbers on the right-hand side and then confirmwith OK . Pull-down menu The pull-down menu can be used to display information (e.g. about a drying programme).  11:02 Time left h 2:...

Operating the tumble dryer 19 Help display With some menus, Help appears along the bottom line of the display.  If you need more information about the current menu, touch the Help  sensor control. The additional information is shown in the display.  Touch the   sensor control to return to the pre...

Initial commissioning 20  Risk of injury or damage to property due to improper installation. Incorrect installation of the tumble dryer can lead to personal injuryor damage to property.Before commissioning the tumble dryer for the first time, make sureit has been installed.Connect the tumble dryer ...

Initial commissioning 21 Setting the display brightness You will be asked to select the brightness of the display. Darker Brighter Display brightness OK  Touch the segment bar for the required level of brightness. The selected level of brightness is represented by the length of thesegment bar.  Co...

Initial commissioning 22  Confirm with the OK  sensor control. The display will change to the next setting. Selecting programme packages You can select various programmes from the programme packages.Any programmes already active are highlighted in orange. 11:02 Cottons  Cottons PRO Label Cottons M...

Initial commissioning 23 If the power is interrupted prior to the start of the first drying pro-gramme (e.g. if the machine is switched off with the   button), the initial commissioning process can be completed again. Once a dryingprogramme has been running for over 10 minutes, the initial commis-s...

Drying 24 1. Notes on correct laundry care Washing beforedrying Heavily soiled laundry must be washed particularly thoroughly. Usesufficient detergent and select a high wash temperature. If in doubt,wash the items several times. The tumble dryer must not be used for drying items of laundrywhich have...

Drying 25 2. Loading the tumble dryer Loading laundryinto the tumbledryer Textiles may be damaged.Before loading, read chapter “1. Notes on correct laundry care” first.  Open the door.  Load laundry into the tumble dryer. Risk of damage with laundry getting trapped.Laundry can be damaged by gettin...

Drying 26 Alternatively, you can select a programme from the Favourites list.The preset programmes under    Favourites cannot be changed via the Supervisor level. 11:02   Programmes  Favourites  Supervisor Help  Touch the    Favourites  sensor control. 11:02 Favourites Cottons Cottons Cottons...

Drying 27  Only press OK when the extra appears on the display. The relevant symbol for the required extra (  or  ) lights up.   Gentle tumble Sensitive items are dried with fewer drum rotations and a lower dryingtemperature.   Anti-crease At the end of the programme, the drum will continue to ...

Drying 28 5. Starting a programme Payment device(optional) If your machine is connected to a payment device, the amount of pay-ment required will appear in the display. Money may be lost if the drum door is opened or the programme iscancelled.Depending on the settings, money may be lost in the payme...

Drying 29 When using the programmes for the first time, the displayed timesometimes deviates significantly from the real time left. The differ-ence between the estimated and achieved time becomes smaller ifthe corresponding programme is run more often. If different loadsizes are dried in one program...

Drying 30 Timer Prerequisite forsetting the timer The  Delay start must be activated in the  Supervisor level in the Con- trols / Display menu so that the Timer can be selected. Before the pro- gramme starts, the Timer can be used to select a programme start time or programme end time. Setting the t...

Programme overview 31 “Label” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Cottons  Cotton items with normalresidual moisture - Machine iron ( 40  %) - Hand iron ( 25  %) - Hand iron plus ( 15  %) - Slightly dry ( ...

Programme overview 32 “Standard” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Cottons Single and multi-layercotton/linen items - Machine iron ( 40  %) - Hand iron ( 25  %) - Hand iron plus ( 15  %) - Slightly dry ( ...

Programme overview 35 “Sport” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Sportswear Polyester or polyamide with and without span- dex - Machine iron ( 40  %) - Hand iron ( 20  %) - Hand iron plus ( 8  %) - Slightl...

Programme overview 36 “Flatwork” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Cottons, dry plus Single and multi-layercotton/linen items - Extra dry ( -4  %) -    Anti-crease * 10 kg  Cottons, dry Single and multi...

Programme overview 37 “Bedding” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Down bedding Down duvets and pillows - Normal ( 0  %) -    Anti-crease * 8 kg  Synthetic bedding Synthetic duvets and pil-lows - Normal ...

Programme overview 38 “Buildings maintenance” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Mops Cotton mops - Machine iron ( 20  %) - Hand iron ( 15  %) - Hand iron plus ( 10  %) - Slightly dry ( 2  %) - Normal ( 0 ...

Programme overview 39 “Fire brigade” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  Masks Breathing masks withhead straps Breathing masks mayonly be tumble dried ifthey are held in place inthe drum by special hold-ers...

Programme overview 40 “WetCare” programme package Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Load size  WetCare sensitive Non-washable outerwear - -    Anti-crease * 4 kg  WetCare silks Non-washable outerwearwhich creases easily - Machine i...

Programme overview 41 “Equestrian” programme package  Risk of damage due to metal buckles, hooks and eye fasteners. Metal buckles, hooks and eye fasteners may damage fabrics and the dryer drum.Remove all metal buckles, hooks and eye fasteners before tumble drying.If the metal buckles, hooks and eye...

Programme overview 42 “Special programmes” programme package You can put together 5 special programmes on the appliance and assign your own pro-gramme names. Enter the programme names in the table. Programme name Suitable fabrics Selectable drying levels (residual moisture in %) Selectable extras Lo...

Programme overview 43 “Individual programmes” programme package You can put together 20 individual programmes in the Miele Benchmark ProgrammingTool (see “Miele Benchmark Programming Tool Manual”) and assign your own programmenames. Enter the programme names in the table. Programme name Suitable fab...

Changing the programme sequence 44 Changing a programme once it has started You cannot change to another programme once a programme hasstarted (this prevents unintentional alterations). You will need to can-cel the current programme before you can select a new one.  Risk of fire due to incorrect us...

Changing the programme sequence 45 Adding laundry during ongoing Delay start period You can open the door to add or remove laundry. - All programme settings will be saved.- You can change the drying level, if required.  Open the door.  Add or remove laundry.  Close the door.  Touch the Start/Sto...

Supervisor level 46 Opening the Supervisor level 11:02   Programmes  Favourites  Supervisor Help Touching the   sensor control takes you to the Supervisor level. Access via code Supervisor level is accessed using a code. Factory default: The code is 000 . Change code You can alter the Superviso...

Supervisor level 47 Language settingThe   sensor control can be used to select a language. All languages are available (fact- ory default).You can change the order of the first 4 languages. These slots are allocated to the mostcommonly used languages.Standard languageThe user language cannot be cha...

Supervisor level 48 - Finish tone The finish tone signals the end of the drying programme. - Keypad tone - Welcome tone - Fault alarm The fault tone signals a fault and can be switched off. The volume of the fault tone cannotbe adjusted. Res. moisture display In addition to displaying the drying lev...

Supervisor level 49 Machine off status In order to save energy, the tumble dryer will switch off automatically after the end of theprogramme or if no further selection is made. You can change this setting. Changing this setting leads to increased energy consumption. - No switch off- Factory default:...

Supervisor level 51 Favourite programmes After switching on, you can also select a programme via:    Favourites . 12 programmes can be stored as favourites based on your own priorities and require-ments. These favourites will also be made available in the control options - Launderette ext. (12 prog...

Supervisor level 52 – Pause: 2–5 seconds – Drum reversal : 15–120 seconds - Anti-crease – Drum rotation, main direction : 0–500 seconds – Pause : 100–3000 seconds – Drum reversal : 0–500 seconds Timed drying : - Running time : 5–180 minutes - Temperature (Process air): cold – 65 °C - Cooling down te...

Supervisor level 53 Prog. colour allocation You can assign a specific colour to a favourite programme. In the list of favourites, each fa-vourite programme is given a coloured frame, which can be adjusted. - Factory default: Off- On Process technology Anti-crease At the end of the programme, the dru...

Supervisor level 54 Service Clean out the airways The tumble dryer ’s electronic module calculates the degree to which fluff or detergentresidues in the fluff filters and vent ducting are impairing performance. A message tocheck the contamination appears. You can decide at what level of fluff this r...

Supervisor level 55 Enter your message for your planned maintenance work. You can edit one, two or all threeof the 1/2/3 messages.Reset displayThe message appears until the display is permanently reset. The message then appearsagain once the next interval is reached. External applications External e...

Supervisor level 56 - Peak load with 230 V - Peak load with 0 V - COM module Peak load prevention - Factory default: Off - On COM module selection This tumble dryer is equipped with an integrated WiFi module. However, the dryer can alsobe equipped with an external module. - Factory default: Off - In...

Supervisor level 57 Remote External programme selection is possible via an external terminal (programme may only bestarted on the machine). However, programmes may also be selected and started on themachine. Factory default: on Remote update The RemoteUpdate function is used for updating the softwar...

Supervisor level 58 Payment system The Miele Connector Box accessory unit or the COM module is required to connect a pay-ment device. Setting for payment systems If you wish to change the settings after the commissioning process, please contact MieleService. - No payment system The next settings are...

Connectivity 59 Pairing instructions Follow the steps below to connect the tumble dryer to your network. Opening the supervisor level  Select the Supervisor menu option in the appliance display.  Select the Access via code menu option.  Enter the 3-digit supervisor code. Establishing the network ...

Connectivity 60 Technical data System requirements for WiFi - WiFi 802.11b/g /n- 2.4 GHz band- WPA/WPA2 encryption- DHCP activated- Multicast DNS / Bonjour / IGMP snooping activated- Ports 443, 80, 53 and 5353 open- IP DNS server = IP standard gateway/router- Mesh/repeater use: same SSID and passwor...

Cleaning and care 61 Cleaning the fluff filter A two-part fluff filter in the air supply area collects fluff released bytextiles. Remove and dismantle the fluff filter for cleaning. Check and clean the fluff filter at the latest when the Clean out air- ways message appears. Tip: You can also use a v...

Cleaning and care 62 Dismantling thefluff filter Flusensieb reinigen Ein zweiteiliges Flusensieb im Luftfüh-rungsbereich fängt anfallende Flusenauf. Es wird zur Reinigung entnommenund demontiert. , Kontrollieren und reinigen Sie das Flusensieb spätestens bei derPrüfmeldung: Luftwege reinigen . Tipp:...

Cleaning and care 63  Insert the inner fluff filter part into the outer part.  Turn the inner part of the fluff filter clockwise slightly until you feel itengage.  Hold the fluff filter by its handle and push it as far as it will go intothe lower air supply area. Do not rotate the handle as this ...

Cleaning and care 64  Risk of damage due to solvent-based cleaning agents and abras- ive cleaners.Solvent based cleaning agents, abrasive cleaners, glass cleaners orall-purpose cleaners can cause damage to plastic surfaces andother parts.Clean the tumble dryer with a slightly damp cloth and a mild ...

Cleaning and care 65 - Cover in door area Only remove the cover in the door area in the event of a majorblockage. Removing thecover  Look in the drum. – Abdeckung im Einfüllbereich , Die Abdeckung im Einfüllbereich sollten Sie nur im Falle einer extremstarken Verstopfung entnehmen. ^ Schauen Sie in...

Problem solving guide 67 Fault diagnosis Message Cause and remedy The display remains dark. There is no power to the tumble dryer.  Check the mains plug, main switch and fuses (on site). Problem Cause and remedy The efficiency of the tumbledryer decreases. The fluff filter in the tumble dryer is di...

Problem solving guide 68 Problem Cause and remedy  When drying, open a door or window to ensure sufficientventilation. The laundry has not been spun sufficiently.  Make sure that your laundry is thoroughly spun at the ap-propriate spin speed in the washing machine. The tumble dryer has been overlo...

Customer Service Department 69 Contact in case of malfunction In the event of any faults which you cannot remedy yourself, please contact your MieleDealer or Miele Service. Contact information for Miele Service can be found at the end of this document. Please note that telephone calls may be monitor...

Installation 70 Installation locations Front view Aufstellsituationen Vorderansicht a Abluftanschluss b Netzanschlussleitung c Bedienungsblende d Tür e Flusenfilterklappe f Vier höhenverstellbare Schraubfüße Installation 3 7 a Vent ducting b Electrical connection cable c Control panel with touch dis...

Installation 71 Rear view 1 2 3 4 5 7 6 a Electrical connection b Communication module slot c Intake vents for drying air d Gas connection 1/2" acc. to ISO 7-1 e Exhaust duct Ø 100 mm f Connection for communication box g Communication box (optional)For setting up a connection with external syste...

Installation 72  Risk of injury and damage due to missing tumble dryer fastenings. When installing on a plinth, an unsecured tumble dryer can slip and fall off the plinth.If the tumble dryer is installed on a plinth, it must be secured.The plinth must be secured to the floor. Installation Transport...

Installation 73 Levelling  Ensure that no closeable door, sliding door or oppositely hinged door is installed thatcould hinder opening of the tumble dryer door in any way. Aufstellen Transportieren Transportieren Sie den Trockner zumAufstellungsort. , Achten Sie beim Transport des Trockners auf des...

Installation 74 ^ Lösen Sie die Schrauben (2). ^ Gleichen Sie Bodenunebenheitendurch Drehen der Schraubfüße (1)aus. ^ Drehen Sie die Schrauben (2) gegendas Gehäuse fest. Trockner gegen Verrutschen sichern , Der Trockner muss an den Trocknerfüßen mit Spannlaschen(Zubehör) gesichert werden. Installati...

Installation 75  If it is necessary to install a residual current device (RCD) in accordance with local regu- lations, a residual current device type B (sensitive to universal current) must be used. Supply air and exhaust air management Ventilation The air required for drying is taken from the room...

Installation 76 Calculating the total ducting length The friction of the vent ducting with its bends and various components provides resistanceto the flow of air. This friction resistance is expressed as a relative pipe length. The relative pipe length indicates how much greater the resistance of a ...

Installation 77 A 1 bend, 90° = 1 x 0.8 m relative pipe length = 0.8 m B/D 2 bends, 90° = 2 x 0.8 m relative pipe length = 1.6 m C 0.5 m pipe = 0.5 x 1 m relative pipe length = 0.5 m Total ducting length = 2.9 m Result: the total ducting length is less than 20 m (as per Table II). A pipe diameter of...

Installation 78 - pipes and connecting pieces from a suitable retailer. Only use heat-resistant materials with a temperature resistance of at least 80 °C. Abluftführung mit gestecktenRohren Sie benötigen – den Anschlussstutzen (liegt bei). – Rohre und Übergangsstücke aus dem Handel. Es dürfen nur wä...

Installation 79  A non-return flap must be installed for each tumble dryer. Otherwise, the tumble dryers may be damaged by a backflow of condensation and theirelectrical safety could be affected. If 3–5 tumble dryers are installed on one shared exhaust air duct, the pipe diameter D must be in- crea...

Installation 80 Gas Connection and conversion instructions Shut-off equipment and connection hose for the gas connection must be fitted by thecustomer on site.A suitable connection hose can be purchased from Miele as an optional accessory. Initial connection The initial connection must be carried ou...

Installation 81 3. If the gas family, gas group or connection pressure is different, it must be converted asinstructed in the connection and conversion instructions (“Setting and conversion in-structions for gas”). You must then change the data plate.Follow the accompanying setting and conversion in...

Installation 83 Country Gas category Connection pressure for natural gas (mbar) Connection pressure for liquid gas (mbar) p n p min p max p n p min p max PL II 2E3P 20 17 25 37 25 45 PT II 2H3P 20 17 25 37 25 45 RO II 2H3B/P 20 17 25 29 25 35 SE II 2H3B/P 20 17 25 29 25 35 SI II 2H3B/P 20 17 25 29 2...

Optional accessories 84  Accessory parts may only be fitted when expressly approved by Miele. If other parts are used, warranty, performance and product liability claims will be invalidated. Communication box The optional communication box allows external hardware from Miele and other suppliersto b...

Optional accessories 85 Copyright and licences For the purpose of operating and controlling the communication module, Miele uses propri-etary or third-party software that is not covered by open source licensing terms. This soft-ware/these software components are protected by copyright. The copyright...

Technical data 86 Height 1020 mm Width 700 mm Depth 763 mm Depth with door open 1248 mm Weight 75 kg Drum volume 180 l Maximum load size 10 kg (weight of dry laundry) Length of supply lead 1600 mm Supply voltage See data plate Rated load See data plate Fuse rating See data plate Lamp wattage See dat...

Malaysia Miele Sdn BhdSuite 12-2, Level 12Menara Sapura Kencana PetroleumSolaris Dutamas No. 1, Jalan Dutamas 150480 Kuala Lumpur, MalaysiaPhone: +603-6209-0288Fax: +603-6205-3768 Miele New Zealand LimitedIRD 98 463 6318 College HillFreemans Bay, Auckland 1011, NZTel: 0800 464 353Internet: www.miele...