Miele G 601 - Manuals

Building in dimensions Dishwasher models G 601 - G 632 Dishwasher models G 636 - G 698, G 975 1) Niche height 870 mm2) Niche height 820 mm Adjustment range approx. 5 cm(82 -87 cm total height). Extended machine feet are available atextra cost, (special accessory) where amachine height of 87 to 92 cm...

1. Fitting protective cover plate to worktop The underside of the worktop isprotected against steam rising from themachine by a special cover plate. , If two different materials meet up at the front edge of the worktop, thenthe join must be concealed by thecover plate. ^ Remove the protective backin...

2. Fitting the facia panel The dishwasher must not be used until the control panel has been correctlyfitted. Dishwashers with selector dial (G 601 - G 624, G 638 - G 686, G 801 - G 824, G 838 - G 884, G 975) ^ Attach cap a to push button switch. ^ Push the ventillation grille b (depending on model) ...

3. Building the dishwasher into a niche Connection to water and drainageshould be sited beside and not behindthe dishwasher for accessibility.Connections are usually made in thearea under the sink. Many kitchen unitmanufacturers provide a cut-out in thebase of the sink base unit for the hosesto be f...

4. Matching the facia panel to the height of adjacent drawerfronts The facia panel can be aligned with thedrawer fronts by adjusting the spacerbars. ^ Using an 8 mm socket spanner turnclockwise or anti-clockwise until therequired height is reached. If necessary some or all spacer barscan be removed....

5. Fitting the (matching) door front Fixing brackets are already fitted onstainless steel door fronts. These frontscannot be shortened.(Go to "Fitting and securing the doorfront".) The door of a kitchen base unit (withoutdrawer front or fittings) is normally usedfor the door front. If a kitc...

^ Drill the fixing holes to a depth ofabout 10 mm, using a 2.5 mm drillbit. ^ Secure the fixing bracket to the doorfront using the countersunk screwssupplied. ^ Take off the templates. Keep the templates in case thedishwasher is ever fitted with a newdoor front. Fitting and securing the door front ^...

6. Securing the dishwasher ^ Open the dishwasher door. The holes in the securing piecesmust line up with the long holes inthe worktop cover plate. If this is notthe case, adjust the position of thedishwasher in the niche (ensure thatthe dishwasher is the same distancefrom the neighbouring kitchen un...

7. Adjusting the door springs The door springs are correctly adjustedwhen the door remains stationary whenleft open at 45 °. If the door drops down, then the doorsprings need to be tightened. If it closes then the springs need to beloosened. The adjusting screw is located in theupper front strip at ...

8. Matching the plinth facing of a kitchen run The plinth area of the dishwasher isnormally covered with a plinth runmatching the kitchen furniture. The height ( H ) of the plinth facing in front of the dishwasher depends on theplinth return ( R ) and how much the door front extends below thedishwas...

Building in dimensions: Dishwasher models G 636 - G 698 G 975 1) Niche height 870 mm2) Niche height 820 mm Adjustment range approx. 5 cm (82 -87 cm total height). Extended machine feet are available atextra cost, (special accessory) if youwish to increase the machine height tobetween 87 and 92 cm. D...

Screw feet ^ Use a TORX T20 screwdriver toadjust the rear screw feet to therequired height. Higher = turn clockwiseLower = turn anti-clockwise Several turns are needed to adjust 1mm in height. ^ Adjust the front screw feet manuallyor with a flat blade screwdriver. Screw the feet out until the seal o...

3. Calculate the decor panel height The height of the dishwasher frontpanel can be adjusted to matchneighbouring kitchen units. To do thisyou will have to trim the decor panel,the filler card underneath it and thedecor frame strips to size. If you wish you can fit a decor panel tomatch your kitchen ...

Adapting the height of the decorpanel supplied ^ Mark the measurement X on the left and right hand side of the decorpanel and on the decor frame strips. ^ Take off and shorten the decor framestrips, the decor panel and the fillercard (see Step 4). Calculating the height of a new decorpanel You can s...

5. Securing the dishwasher To ensure stability, the dishwasher mustbe fixed securely to the worktop. Twosecuring pieces are supplied with thedishwasher for this purpose. ^ Fit the securing pieces into the slotson both the left and right hand sides. ^ Push the dishwasher right back intoits recess (ma...

6. Adjusting the door springs The door springs are correctly adjustedwhen the door remains stationary whenleft open at 45°. If the door drops down, the doorsprings need to be tightened. If the door rises up the springs need tobe loosened. The adjusting screw is located in theupper front strip at the...

7. Adjusting the plinth return The plinth return on a "U" modeldishwasher can be adjusted between35 and 100 mm in 2.5 mm increments. ^ Push the spring clips on either side ofthe dishwasher outwards and pushthe brackets right in. On dishwashers G 636 - G 698 G 975 The fixing brackets face inw...

The plinth facing has two cutting lines. ^ Screw the plinth facing on to thebrackets with the cutting linestowards the top. Then pull the facingout evenly to align it with plinthfacings on adjoining kitchencabinets. If you have pulled the plinth facingout too far you must not attempt topush it back ...

8. Matching the plinth facing of a kitchen run The plinth facing supplied will fit withoutmodification: – for a maximum plinth return of 100 mm – and when the machine is set to its maximum height (feet fully extended- max. 5 cm). If the machine height is lower than themaximum, and the plinth recess ...

, Please follow the installation instructions carefully.All electrical work should be carriedout only by a suitably qualified andcompetent person, in strictaccordance with national and localsafety regulations.Ensure power is not supplied to theappliance while installation work isbeing carried out. T...

Connection to the water inlet , Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max.60 °C. When connected to a hot wa-ter supply all programme stageswhich would otherwise be carried outwith cold water (pre-wash andinterim r...

Drainage – The machine drainage system is fitted with a non-return valve, whichprevents dirty water from flowingback into the machine via the drainhose. – The dishwasher is supplied with an approx. 1.5 m long flexible drain hosewith an internal diameter of 22 mm. – The drain hose can be extended usi...

"i"- Integrated dishwashers If you would like to... you will need to order... ...convert an integrated ("i") dishwasherto a built under "U" model ...a GDU decor set conversion kitavailable in: white dark brownblack ... build the dishwasher into a kitchen whichdoes not have a ...

Dishwasher model G 601 - G 632 G 801 - G 832 Height Freestanding 84.7 cm(adjustable + 2.0 cm) - Height built-in models 81.7 cm(adjustable + 5.0 cm) 83.7 cm(adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 44.8 cm 44.8 cm Width of building in recess 45 cm 45 c...