Miele 371 G - Manuals

Building in Fit wall units and extractor hoodbefore fitting the hob, to avoiddamaging the appliance. ~ The veneer or laminate coating of worktops (or adjacent kitchen units)must be treated with 100 °Cheat-resistant adhesive which will notdissolve or distort.Any backmoulds must be ofheat-resistant ma...

~ The room in which the gas hob is installed must be at least 20 m 3 in size with a door or window in it which canbe opened to the outside air. ~ Using the gas hob will cause a build-up of heat and moisture in theroom in which it is installed. Ensure thatthe room has sufficient natural ormechanical ...

KM 370 a Building-in depth b Mains connection box c Gas connection R 1 / 2 - ISO 7-1 (DIN2999) Appliance dimensions and worktop cut-out 7

Building in the appliance ^ Feed the electricity connection cablethrough the cut-out and connect. ^ Place the gas hob in the preparedcut-out. ^ Make the gas connection (seerelevant section). Securing the appliance KM 371 G / KM 391 G ^ Secure the gas hob at the front and rear with fixing brackets a ...

All electrical work should be carriedout by a suitably qualified andcompetent person, in strictaccordance with current local andnational safety regulations (BS 7671in the UK). Installation, repairs and other workby unqualified persons could bedangerous. The manufacturercannot be held liable forunaut...

Important The electrical safety of this appliancecan only be guaranteed whencontinuity is complete between it andan effective earthing system, whichcomplies with current local and nationalsafety regulations. It is most importantthat this basic safety requirement ispresent and regularly tested and wh...

Connection to the gas supply, orconversion from one type of gas toanother should only be undertakenby an approved and registered gasinstaller in strict accordance withlocal and national safety andbuilding regulations, (e.g. Corgiregistered in the U.K.) Everyappliance should have its ownisolating val...

a Connection with test pointspecifically for GB b Connection with test pointspecifically for GB and 90° angle Natural gas / liquid gas ^ The appliance is supplied with anR 1/2" - ISO 7-1 (DIN 2999) gasconnection point. ^ An appropriate rigid connection andisolating valve must be installed forfin...

Nominal rating for all gas types with the burner full on Burner Gas type KM 370 G / KM 370-1 G / KM 371 G KM 390 G / KM 391 G kW g/h kW g/h Smallburner Natural gas HLiquid gas 1.001.00 - 73 1.001.00 - 73 Normalburner Natural gas HLiquid gas 1.751.75 - 127 1.751.75 - 127 Largeburner Natural gas HLiqu...

KM 370 G / KM 370-1 G /KM 371 G When converting to anothe type ofgas, the main jets and the small jetson all burners have to be changed. Screw in the new jets according tothe following table. For U.K. and IE Main jet Ø Small jet Ø Natural gas H Small burner Medium burner Large burner Wok 0.76 1.00 1...

Changing the jets Disconnect the gas hob from theelectricity supply by switching off atthe socket and withdrawing the plugor by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d . ^ Using an M7 socket spanne...

Wok burner ^ Take off the burner cap a , burner ring b and burner head c . ^ Loosen screws d and remove the cover plate. ^ Using an M7 socket spannerunscrew the main jets e (larger diameter jet) and f (smaller diameter jet). ^ Change the main jets. Conversion to another type of gas 22

Changing the small jets (for all burners) To change the small jets, the burnersecuring screws must first be loosenedand the upper section of the applianceremoved. ^ Remove the operating controls bypulling them upwards. ^ Remove the upper section. N.B. To remove a ceramic uppersection:Insert the leve...

After changing the jets ^ Assemble the removed burner partsin reverse order and check for leaksby operating the burner without theupper section of the hob in place(use a match to ignite the flame). ^ Remove the burner parts again. ^ Then replace the upper section of thehob. ^ Screw in the burner bas...

Changing the small jets To change the small jets, the burnersecuring screws must first be loosenedand the upper section of the applianceremoved. ^ Remove the operating controls bypulling them upwards. ^ Remove the upper section. N.B. To remove a ceramic uppersection:Insert the lever supplied between...