Miele 05 620 661 - Manuals

Disposal of the packingmaterial The cardboard box and packagingprotect the appliance during shipping.These materials are biodegradable andrecyclable. Please recycle. Ensure that any plastic wrappings,bags etc. are disposed of safely andkept out of the reach of children.Danger of suffocation! Disposa...

Opening the door without apanel in place ^ Gently pull on the upper portion ofthe mounting bracket until the doorlatch releases (small arrow). Without the mounting bracket inplace: ^ Grip the T shaped opening with a fin-ger and pull the door open. Opening the door 8

G 600 Series Dishwashers Full size models G 643 - G 663 Removing the leg extensions The black leg extensions can be re-moved to reduce the machine height to32 1 / 4 " - 33" (819-838 mm) (see Inset). A = Black leg extension (removable)B = White leg (must be installed on machine). ^ After remo...

G 800 Series Dishwashers Full size models G 843 - G 863 Machine heights of 35" - 37"(889-940 mm) cannot be obtainedusing the supplied legs.For this height range, or for heightsgreater than 35" (889 mm), extendedlegs (part# 02 702 601) are neces-sary.Contact the Miele Technical ServiceDep...

1. Install the steam deflector A stainless steel steam deflector is sup-plied to protect the countertop fromsteam and condesation when the dish-washer is opened. If the countertop ismade of Corian®, granite, marble orother solid, waterproof material, thesteam deflector is not required. The steam def...

Stone or marble countertops: The steam deflector is not required forcountertops made of solid, waterproofmaterial. But it is needed for determin-ing the correct position of the opticindicator reflector. ^ Remove the black plastic reflectorholder from the steam deflector. ^ With the reflector cut out...

2. Install the mountingbrackets To ensure stability this dishwashershould be securely attached to thecountertop with the two mountingbrackets included. ^ Insert the tab of each bracket into theguide holes on top. Stone or marble counterops:Do not install these mounting bracketsif the counter is made...

6. Install the custom door panel A custom door panel must be installedon the dishwasher before it can besafely operated. A single large panel ora two piece panel separated at thedrawer line can be used. Panel size is determined in the follow-ing manner: Panel Height = HTC - TKH HTC = Height to the u...

The door panel is attached to the dish-washer using the mounting bracket thatcomes secured to the front of the unit. To remove the bracket: ^ Open the door 2 - 4" (5 - 10 cm). ^ Loosen the bracket retaining screw(black arrow) located on each side ofthe machine door. ^ Pull the bracket up until t...

Install the bracket on the rear of thecustom door panel ^ Make sure the dishwasher is level. ^ Measure the distance X between the round hole in the machine outer doorpanel (shown in inset) and the loweredge of the adjoining cabinet door. ^ Place the door panel on a flat sur-face, good side face down...

^ Place the bracket on the door panelso the notches, a , cross the previ- ously drawn centerline, and the bot-tom of the bracket lines up with thehorizontal X line. ^ Mark and drill pilot holes for thescrews using a 3 / 32 " (2.5 mm) drill bit. ^ Attach the bracket to the back of thepanel, using...

8. Secure the dishwasher ^ Open the dishwasher door. If the steam deflector is installed, themounting bracket holes must alignwith the slots in the steam deflector. ^ Using flat head screws, secure thedishwasher to the countertop byscrewing through both the mountingbracket and the steam deflector. M...

For openings exactly 23 5 / 8 " (60 cm) wide: ^ Open the dishwasher door and re-move the caps covering the mount-ing holes on the outer edge of thewash cabinet. ^ Fasten the dishwasher to the adja-cent cabinets using the suppliedscrews and bushings. A bushingmust be placed over the screw be-fore...

9. Adjust the door springs ^ Open the dishwasher door halfway. If the door remains in this position whenreleased, the springs are adjusted cor-rectly. If the door drops, the tension on thesprings needs to be increased. If it closes on its own, the tension on thesprings need to be decreased. ^ To adj...

10. Make the plumbing connections An air gap is built into the water inletsystem to prevent potable water frommixing with waste water. The dishwasher can heat its own waterto the temperatures required by thewash program. This allows the option ofconnecting the machine to either a hotor cold water so...

Venting the drainage system If the dishwasher drain hose is con-nected to a floor drain or to a drain pipe that is less than 8" (20 cm)above the floor, the drain must be vented. Otherwise the water inside thedishwasher may siphon out during thewash program. To vent the drain: ^ Open the dishwash...

11. Make the electrical connection GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BEGROUNDED. In the event of a malfunction or breakdown, grounding will reduce the risk ofelectric shock by providing a path ofleast resistance for the electric current.This appliance is equipped with a cordhaving an equipm...

Power outlet The power outlet for the appliance mustbe installed within a cabinet, on a walladjacent to the undercounter space inwhich the dishwasher is located. An o-pening through the partition betweenthe compartments of 1 1 / 2 " (3 to 4 cm) can be made to allow the plug to passthrough. Perma...

13. Install the toekick For installations using a continuoustoekick or a cabinet matching toekick Before installing the toekick, measure-ments must be taken to ensure that thetoekick will not interfere with the com-plete opening of the dishwasher door. The door panel overhang ( P ), and toekick dept...

^ Carefully open the dishwasher dooruntil it hits the toekick. ^ Using the front lower edge of thedoor panel as a guide, draw a lineacross the toekick. ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close tothe line just drawn, score the front ofthe toekick, and snap off the exce...