Miele 05 585 951 - Manuals

Building in dimensions Dishwasher models G 643 - G 663 1) Machine height 870 mm 2) Machine height 820 mm Adjustment range approx. 5 cm(82 -87 cm total height). Extended machine feet are available atextra cost, (special accessory) where amachine height of 87 to 92 cm is re-quired. Dishwasher models G...

1. Fitting protective cover plate to worktop The plexiglass relfector panel and allother installation items required areincluded in the accessories packsupplied with the dishwasher. When the dishwasher is built-in, theleft hand side of the reflector panelmust be sited above the in-operationlight in ...

^ Align the cover plate to the frontedge of the worktop in the middle of the niche.If the worktop has a very rounded edge, pull the cover plate further for-ward so that the reflector panel is stillvisible later on. ^ Use the tacks supplied to nail thecover plate to the underside of theworktop.Workto...

2. Building the dishwasher into a niche Connection to water and drainageshould be sited beside and not behindthe dishwasher for accessibility.Connections are usually made in thearea under the sink. Many kitchen unitmanufacturers provide a cut-out in thebase of the sink base unit for the hosesto be f...

3. Fitting the matching door front The front of the dishwasher needs to befitted with a base unit front to match thekitchen furniture. This door front may bea single panel or a two-piece panel, di-vided to give a dummy drawer facialine. Dimensions: Width:to match the door of a 60 cm wide baseunit.To...

Fitting the door front The door front is correctly fitted when: – the lower lugs on the fixing bracket rest firmly in the lower slits of thedishwasher outer door panel, – the prongs of the fixing bracket lie on the sprung bolts in the upper cornersof the dishwasher door, – the recess in the middle o...

4. Adjusting the door front When fitted the door front can be ad-justed up to a maximum of 2 mm up-wards or downwards to match adjoiningunit fronts. ^ Open the dishwasher door slightly. ^ With the door open, press the frontpanel on one side against the doorouter panel. ^ Adjust the height of the doo...

5. Securing the dishwasher ^ Open the dishwasher door. The holes in the securing piecesmust line up with the long holes inthe worktop cover plate. If this is notthe case, adjust the position of thedishwasher in the niche (ensure thatthe dishwasher is the same distancefrom the neighbouring kitchen un...

6. Adjusting the door springs The door springs are correctly adjustedwhen the door remains stationary whenleft open at 45 °. If the door drops down, then the doorsprings need to be tightened. If it closes then the springs need to beloosened. The adjusting screw is located in theupper front strip at ...

7. Matching the plinth facia of a kitchen run The plinth area of the dishwasher isnormally covered with a plinth runmatching the kitchen furniture. The height ( H ) of the plinth facia in front of the dishwasher depends on theplinth return ( R ) and how much the door front extends below the dish-was...

, Please follow the installation in- structions carefully.All electrical work should be carriedout only by a suitably qualified andcompetent person, in strict accor-dance with national and local safetyregulations.Ensure power is not supplied to theappliance while installation work isbeing carried ou...

Connection to the water inlet , Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max.60 °C. When connected to a hot wa-ter supply all programme stageswhich would otherwise be carried outwith cold water (pre-wash and in-terim...

Drainage – The machine drainage system is fit- ted with a non-return valve, whichprevents dirty water from flowingback into the machine via the drainhose. – The dishwasher is supplied with an approx. 1.5 m long flexible drain hosewith an internal diameter of 22 mm. – The drain hose can be extended u...

You would like to... Then you need... ... build the dishwasher into a kitchen whichdoes not have a matching plinth run ...a separate plinth kitavailable in: white black ... adjust the height of the dishwasher tobetween 87 cm and 92 cm (G 643 - G 663)or between 89 cm and 94 cm (G 843 - G 863) ...kit ...

Dishwasher model G 643 G 843 Height 81.7 cm(adjustable + 5.0 cm) 83.7 cm(adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 59.8 cm 59.8 cm Width of building in recess 60 cm 60 cm Depth 57 cm 57 cm Depth with door open 115.5 cm 120.5 cm WeightFully integratedFu...