Metrologic MS9524 - Manuals

8 I NSTALLING THE S CANNER TO THE H OST S YSTEM Integrated Full Speed USB MS9524-40 and MS9544-40 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector of the USB cable into the jack on theVoyager PDF . You will hear a ‘click’ when the connection is made. 3. Connect the other end of...

12 S TAND K ITS Free Standing Kits #46-46128 a. Stand ( MLPN 36-00454) ............................. Qty 1 b. Apron ( MLPN 50-50440 )............................. Qty 1 c. Screw, M3 x 6 mm ( MLPN 18-18670 ) ........ Qty 2 d. Washer, #5 x .5 OD ( MLPN 18-18671) ...... Qty 2 e. Stand Anchor ( MLPN 50-...

13 A SSEMBLING THE S TANDS There are 2 options for assembling the stand. The first option allows the stand tobe self-supporting and moved freely or placed anywhere on the countertop. Thesecond option is used if the stand will be bolted/hard-mounted to the countertop. Stand Option 1: Self-supported F...

14 A SSEMBLING THE S TAND (C ONTINUED ) Stand Option 2: Hard-mounted to countertop ( continued ) For use with kits #46-46128, #46-46351 andMS951 Stand Replacements Step 3 Screw the stand anchor ( MLPN 50-50449 ) onto the base assembly until it sits flush. Step 4 Remove the logo plate on the stand by...

17 A UDIBLE I NDICATORS When the Voyager PDF is in operation, it provides audible feedback. These sounds indicate the status of the scanner . Eight settings are available for the tone of the beep (normal, 6 alternate tones and no tone). To change the tone,refer to Metrologic's programming guide, MLP...

18 V ISUAL I NDICATORS The MS9544 has three LED indicators (blue, white and yellow) located on thehead of the scanner. The MS9524 has two LED indicators (blue and white)located on the head of the scanner. When the scanner is on, the flashing orstationary activity of the LEDs indicates the status of ...

19 V ISUAL I NDICATORS ( CONTINUED ) Alternating Flashing of Blue and White This indicates the scanner is program mode. A razzberrytone indicates that an invalid bar code has been scannedwhile in this mode . The scanner needs to have a Flash ROM upgrade if thealternating flashing of the white and bl...

20 F AILURE M ODES One Razzberry Tone – On Power Up or During Scanning This indicates the scanner has experienced motor or laserfailure Three Beeps – On Power Up If the scanner beeps 3 times on power up then the non-volatile memory (NovRAM) that holds the scannerconfiguration has failed. If the scan...

21 P ROGRAMMING M ODES The MS9524/44 Voyager PDF Series has 3 modes of programming. ¾ Bar Codes Voyager PDF or Voyager PDF with CodeGate can be configured by scanning the bar codes located in Metrologic's programming guides, MLPN 00-02544 and MLPN 00-02990 or MetroSet2’s help files. Please refer to ...

23 P ROGRAMMING M ODES ( CONTINUED ) EXAMPLE #3: The following example shows the events that occur when an invalid bar codeis sent. This sample will load the factory default settings and then set thebaud rate to 19200. HOST SCANNER FEATURE COMMAND ASCII REPRESENTATION RESPONSE Enter Program Mode [st...

24 U PGRADING THE F LASH ROM F IRMWARE The Meteor™ program is a functional component of Metrologic’s new line of Flash- based scanners. This program allows the user of a Metrologic scanner toquickly upgrade to a new or custom version of software. It requires the use of apersonal computer running und...

26 D EPTH OF F IELD Figure 33. Minimum Bar Code Element Width A B C D E F G H J K mm .13 .15 - - .19 - .25 .33 .53 - mils 5.2 5.7 - - 7.5 - 10 13 21 - Specifications subject to change without notice.

27 D EPTH OF F IELD Figure 34. PDF417 Minimum Bar Code Element Width A B mm .25 .38 mils 10 15 Specifications subject to change without notice.

28 IR A CTIVATION Figure 35. Specifications subject to change without notice.

30 T ROUBLESHOOTING G UIDE The following guide is for reference purposes only. Contact a Metrologicrepresentative at 1-800-ID-Metro or 1-800-436-3876 to preserve the limitedwarranty terms. All Interfaces MS9524/44 Series Troubleshooting Guide Symptoms Possible Causes Solution No LEDs, beepor laser N...

35 D ESIGN S PECIFICATIONS D ESIGN S PECIFICATIONS O PERATIONAL Light Source: Visible Laser Diode 650 nm ± 10 nm Laser Power: Less than 1 mW (peak) Depth of Scan Field: 0 mm – 200 mm (0” – 8”) for 0.330 mm (13 mil) bar code atdefault setting Scan Speed: 180 ±10 scan lines per second Scan Pattern: Si...

36 D ESIGN S PECIFICATIONS D ESIGN S PECIFICATIONS E LECTRICAL Input Voltage: 5.0VDC ± 0.25V Power: Operating = 900 mW (typical) Standby = 325 mW (typical) Current: Operating = 180 mA @ 5VDC (typical) Standby = 65 mA @ 5VDC (typical) DC Transformers: Class 2; 5.2VDC @ 650 mA Laser Class 1: IEC 60825...

42 1 10 S CANNER AND C ABLE T ERMINATIONS Scanner Pinout Connections MS9524/44-41 RS-232C and Light Pen Emulation Pin Function 1 Ground 2 RS-232 Transmit Output 3 RS-232 Receive Input 4 RTS Output 5 CTS Input 6 DTR Input/LTPN Source 7 Reserved 8 LTPN Data 9 +5VDC The MS9524 and MS9544scanner interfa...

46 L IMITED W ARRANTY The MS9524/44 series scanners are manufactured by Metrologic at its Blackwood, NewJersey, USA facility. The MS9524/44 series scanners have a five (5) year limited warrantyfrom the date of manufacture. Metrologic warrants and represents that all MS9524/44series scanners are free...

47 Notices and Cautions Notice This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment ge...

49 Index A AC Input/Outlet .................. 5, 6, 7, 8Accessories ................................... 2Adapter .......................................... 2Approvals .................................... 25Audible .................................. 16, 17Autodiscriminates ........................ 35...