La Crosse Technology WS-9025U - Manuals

BATTERY INSTALLATION: 1. First, insert the batteries into the Weather Projection Station (see “T o install and replace batteries in the Weather Projection Station ”). Once the batteries are in place, all segments of the LCD will light up briefly and a short signal tone will sound. Then the ALM1 6:00...

If the batteries are used as the main power source: 1. Projected image brightness, alarm volume and back-light strength will be weaker when batteries are low 2. Battery life time will be much less than 1 year; depending on the frequency of projection and alarm. TO USE THE PROJECTOR POWER ADAPTER The...

sensors in the order of set-up, i.e. the first sensor will have the temperature/humidity displayed with the number 1 against it and so on. 5. With less than 3 sensors received, the Weather Projection Station will try to pick up the remaining one in approximately another 3 minutes. If 3 sensors are r...

up the Weather Projection Station again. Proceed from step 1 in “Setting Up”,“Battery Installation” or “How to use the Projector Adaptor” . HOW TO USE THE PROJECTOR The projector projects the current time and the current outdoor temperature onto the ceiling, preferable within a darkened room. The pr...

ALARM 1 key HOUR/IN key MIN/OUT key ALARM 2 key DIRECTION key SET key CH/+ key DISPL key SNOOZE key as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For more detail, visit http://www.boulder.nist.gov/timefreq.htm. To listen to the NIST time, call (303)499-7111. This number will connect ...

Moon phase icon Alarm time Weather tendency indicator Time Calendar display Indoor relative humidity in RH% Time reception icon (for WWVB time) Alarm icon Indoor temperature in ºF/ ºC Weather forecast icon Outdoor data signal reception indicator Outdoor temperature in ºF/ ºC Outdoor sensor identific...

MANUAL SETTINGS: The following manual settings can be changed when pressing the SET key for: • LCD contrast setting • Time zone setting • DST (Daylight Saving Time) setting • Time reception ON/OFF setting • 12/24-Hour setting • Manual time setting • Calendar setting • Snooze setting • °F/°C setting ...

MANUAL TIME SETTING: In case the Weather Projection Station cannot detect the WWVB-signal (for example due to disturbances, transmitting distance, etc.), the time can be manually set. The clock will then work as a normal Quartz clock. 1. The hour digit will start flashing. 2. Use the CH/+ key to set...

Icons flashing SNOOZE SETTING: The snooze time can be set OFF to a maximum time of 30 minutes (default is 10 minutes): 1. Use the CH/+ key to set the snooze time. Each pressing of the key will increase the snooze time by 5 minutes. The snooze can also be set OFF when the “OFF” digit is being display...

ALARM SETTING: The alarm time can be set when pressing the ALARM 1 or ALARM 2 key. 1. Press the ALARM 1 or ALARM 2 key until the alarm digits flash. 2. Use the HOUR/IN key to set the alarm hour. 3. Use the MIN/OUT key to set the alarm minute. 4. Confirm with the ALARM 1, ALARM 2, or Snooze key and e...

New Moon Full Moon Small Waxing Crescent Large Waning Gibbous Large Waxing Crescent Small Waning Gibbous First Quarter Last Quarter Small Waxing Gibbous Large Waning Crescent Large Waxing Gibbous Small Waning Crescent Moon Tide: The moon Tide information is indicated on the left side of the moon pha...

The icons displayed forecasts the weather in terms of getting better or worse and not necessarily sunny or rainy as each icon indicates. For example, if the current weather is cloudy and the rainy icon is displayed, it does not mean that the product is faulty because it is not raining. It simply mea...

TOGGLING AND RESETTING THE OUTDOOR RECORDINGS: 1. To toggle between the outdoor current, MIN/MAX temperature and humidity data and the times (for temperature data only) they were recorded press the MIN/OUT key: Once to show the MAX outdoor temperature and humidity data with the recorded time and dat...

1. The distance of the Weather Projection Station or sensor should be at least 6 feet (2 meters) away from any interfering sources such as computer monitors or TV sets. 2. Avoid placing the Thermo-hygro sensor onto or in the immediate proximity of metal window frames. 3. Using other electrical produ...

• Do not submerge the units in water. • Immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of the recommended type. • Do make any repair attempts to the units. Return it to their original point of purchase for repair by a qualified engineer. Ope...

• This product is only designed to be used in the home as indication of the future weather and is not 100% accurate. Weather forecasts given by this product should be taken only as an indication and not as being totally accurate. • The specifications of this product may change without prior notice. ...

of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference.....