JL Audio XD700/5 - Manuals - manualsarea.com

Page 4 - PRODUCT DESCRIPTION; The XD700/5 can be operated with a wide; TYPICAL INSTALLATION SEQUENCE; The following represents the sequence

4 | JL Audio - XD700/5 Owner’s Manual PRODUCT DESCRIPTION The JL Audio XD700/5 is a five-channel, system amplifier utilizing JL Audio NexD™ ultra-high speed switching technology for its four main channels and NexD™ high-speed switching for its subwoofer channel. The NexD™ technologies deliver outsta...

Page 6 - INPUT SECTION

6 | JL Audio - XD700/5 Owner’s Manual TURN-ON LEAD The XD700/5 uses a conventional +12V remote turn-on lead, typically controlled by the source unit's remote turn-on output. The amplifier will turn on when +12V is present at its “Remote” input and turn off when +12V is switched off. If a source unit...

Page 10 - When a pair of the XD700/5’s main channels; SUBWOOFER OUTPUTS; The XD700/5’s single subwoofer channel is; You will notice that there are two “+” positive

10 | JL Audio - XD700/5 Owner’s Manual When a pair of the XD700/5’s main channels are bridged, they will deliver 200W x 1 into a 4 ohm load or 150W x 1 into an 8 ohm load. Operating a pair of bridged channels into a load lower than 4 ohms is not recommended. A bridged pair of channels requires that ...

Page 11 - STATUS LED / PROTECTION CIRCUITRY; There is a single multi-color LED on the top; SERVICING YOUR JL AUDIO AMPLIFIER; If your amplifier fails or malfunctions, please

11 STATUS LED / PROTECTION CIRCUITRY There is a single multi-color LED on the top surface of the amplifier to indicate the amplifier’s operating status. 1) Flashing Green: amplifier is powering up, audio output is muted. 2) Constant Green: amplifier is on and functioning normally, audio output is ac...

Page 12 - SYSTEM CONFIGURATIONS; Crossover Setup for Bi-Amplified System; Mode” switch and select an appropriate “Filter; Crossover Setup for Tri-Amplified System; “Filter Freq.” setting. The “24dB” setting engages

12 | JL Audio - XD700/5 Owner’s Manual SYSTEM CONFIGURATIONS The XD700/5 is a very flexible amplifier, well- suited for a multitude of system configurations. In this section, the most likely configurations for a system with a single XD700/5 are explained in detail. Once you have selected your desire...

Page 14 - Following the directions below will allow the; Necessary Equipment; amplifier’s speaker output connectors.; not recommended

14 | JL Audio - XD700/5 Owner’s Manual APPENDIX A:Input Sensitivity Level Setting Following the directions below will allow the installer to adjust the input sensitivity of each amplifier channel pair simply and easily in just a few minutes using equipment which is commonly available in installation...

Page 15 - Rated Power at 14.4V with less than; Detent Panel Actual

15 APPENDIX C:XD700/5 Specifications: Recommended Fuse Value: 60A Recommended Fuse Type: MAXI® or AGU Input Sections: No. of Inputs: Three Stereo Pairs Input Type: Differential-balanced with RCA jack inputs Input Range: 100mV - 4V RMS Amplifier Section: Amplifier Topology: NexD™ Ultra-High Speed Cla...

Page 16 - contact with the input jacks on the amplifier.; APPENDIX D: TROUBLESHOOTING

16 | JL Audio - XD700/5 Owner’s Manual “How do I properly set the input sensitivity on my amplifier?” Please refer to Appendix A (page 14) to set the input sensitivity for maximum, low-distortion output. “My amplifier doesn’t turn on.” Check the fuse, not just visually, but with a continuity meter. ...

Page 20 - If you need service on your JL AUDIO product:; (do not send product for repair to this address); International Warranties:; by that country’s distributor and not by JL Audio, Inc.

LIMITED WARRANTY - AMPLIFIERS (USA) JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years. The warranty is extended to three (3) years total if installation is performed by an authorized JL Audio dealer using a JL Audio Premium Power Connecti...