JL Audio SB-MA-3-SDN/10W3v3 - Manual
JL Audio SB-MA-3-SDN/10W3v3 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Continued on Next Page; s t e P 7; Place sealant sheet provided over modified area as shown; s t e P 4
- Page 3 – If you are installing this stealthbox® enclosure into a; Put tool panel into place as shown.
- Page 4 – the following steps apply onlY if you are installing this
- Page 5 – I n C l u d e d H a R d W a R e; * ( M a z d a 3 o n l Y n o t I n C l u d e d W I t H M a z d a s P e e d 3 ); s P e C I F I C a t I o n s; ohms mono; P o W e R R e C o M M e n d a t I o n; Fits JL Audio Models:
I n s t a l l a t I o n G u I d e
for the
SB-M-3-SPD/10W3v3
sKu# 94378/ 94379
20007+ Mazda 3/ Mazda speed 3
Thank you for choosing a JL Audio Stealthbox
®
for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox
®
installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation,
please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
®
be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
s t e P 1
In the Mazda3, remove carpeted floor panel by unsnapping
at rear-most edge then remove tool panel.
In the Speed3, remove the foam floor riser.
Continued on Next Page
s t e P 2
Remove bolt securing spare tire with lug wrench provided in
tool panel then remove spare tire.
s t e P 3
Remove sealant material from around mounting boss at
center of spare tire well.
SB-M-3-SPD/10W3v3 INSTR_SKU# 011255
InstallatIon
d I F F I C u l t Y :
3
5
o u t
o F
estIMated tIMe:
2-3 HouRs
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Continued on Next Page SB-M-3-SPD/10W3v3 INSTR_SKU# 011255 s t e P 7 Remove Stealthbox® from packaging and install 3/8 X 2.25 mounting studs into threaded inserts at bottom of enclosure. Thread driver’s side stud in, leaving about 1 1/2-inches extended. Thread passenger side stud in, leaving only ab...
Continued on Next Page SB-M-3-SPD/10W3v3 INSTR_SKU# 011255 s t e P 1 4 Place foam floor supports into cargo area as shown. note that the foam supports have been changed since this photograph was taken to multiple square blocks. If you are installing this stealthbox® enclosure into a Mazdaspeed3, ple...
Continued on Next Page SB-M-3-SPD/10W3v3 INSTR_SKU# 011255 s t e P 2 0 Remove screws securing rearmost edge of plastic floor sup-port panel located across front of cargo area. install 7/8 inch spacers with #8 x 2.25 screws to lift rear edge of panel as shown s t e P 1 9 Place driver’s side cargo flo...
