Jet JOVS-10 - Manuals - manualsarea.com

Page 3 - WARNING

3 WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. This sander is intended to be used with wood and wood products only. Use of this sander and a dust collector with metal products is a potential ...

Page 4 - AVOID kickback by sanding in accordance with directional arrows.

4 • ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or ris...

Page 5 - Grounding Instructions

5 Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an el...

Page 7 - Contents of the Shipping Container; Read and understand the entire contents of; Unpacking

7 Contents of the Shipping Container 1. Sander 3. Table Insert Rings 2. Spindle Wrenches 1. 2mm Hex Wrench 10 Removable Spindles 1/4” x 5” Steel and Sanding Sleeve 3/8” x 6” Steel and Sanding Sleeve 1/2” x 6” Steel and Sanding Sleeve 5/8” x 6” Steel and Sanding Sleeve 3/4” x 9” Steel and Sanding Sle...

Page 8 - Disconnect the sander from the power; Removing Sanding Assemblies

8 Mounting Sanding Sleeves 1. Thoroughly clean the arbors (A, Fig. 1) on all of the spindle assemblies. Also clean the arbor housing on the sander. 2. Slip the sanding sleev e (B, Fig. 1) ov er the spindle and hold in place by tightening the set screw (C, Fig. 1) with the supplied 2mm hex wrench. 3....

Page 9 - the “0” position on the scale.

9 Table Insert 1. Disconnect the sander form the power source, unplug. 2. Choose the insert (A, Fig. 4) that most closely matches the diameter of the sanding drum. 3. Line up the notch in the insert with the spring pin in the table (B, Fig. 4), and press in place. 4. Remove the insert by pressing up...

Page 10 - oil capacity is two quarts.

10 Replacing Sanding Sleeves 1. Loosen hex nut (A, Fig. 7) with a 26mm wrench, or large adjustable wrench. 2. Slide the sanding sleev e (B, Fig. 7) off the drum and replace with a new sanding sleev e. Note: If the sanding sleev e is not easily removed cut the sleev e off and clean the drum before re...

Page 11 - Sander will not start

11 Troubleshooting Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 4. Starting capacitor bad 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord 4. Replace startin...

Page 12 - Breakdown for the JET Oscillating Spindle Sander

12 Breakdown for the JET Oscillating Spindle Sander

Page 13 - Description

13 Parts List for the JET JOVS-10 Oscillating Spindle Sander Index Part No. No. Description Size Qty. 7 .......... OVS10-007 .................. Power Cord ........................................... ............................................... 1 11 ........ KEY5525...................... Key ........

Page 15 - Sanding Assemblies

Page 18 - Wiring Diagram