Jet OES-80CS - Manual - manualsarea.com

Page 2 - Warranty and Service

2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these W MH Tool Group Authorized Service Centers can...

Page 3 - Table of Contents

3 Table of Contents Warranty and Service .............................................................................................................................. 2 Table of Contents ...................................................................................................................

Page 7 - Unpacking; Shipping Contents; Cabinet Hardware; Tools Needed for Assembly

7 Unpacking Upon delivery, open shipping containers and check that all parts are in good condition. Any damage should be reported to your distributor and shipping agent immediately. Before proceeding further, read your manual and familiarize yourself thoroughly with assembly, maintenance and safety ...

Page 8 - Assembly; Stand Assembly

8 Assembly Stand Assembly Referring to Figure 1: 1. Remove all contents from the shipping container. 2. Clean all rust protected surfaces with a mild solvent. Do not use paint or lacquer thinner, gasoline, or mineral spirits; these will damage painted surfaces. 3. Attach the four rubber pads (A) to ...

Page 9 - Sanding Belt Installation

9 Referring to Figure 3: 4. The sanding platen (A) is presently in the horizontal position. Pull lock handle (B) forward to unlock the platen assembly. 5. Tilt sanding platen to the vertical position (C), which will look like D in Fig. 4; then push the lock handle (B) to lock the platen assembly in ...

Page 11 - Electrical; Grounding Instructions

11 Electrical Grounding Instructions This sander must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with ...

Page 12 - Extension Cords; Adjustments; Sanding Platen Angle Adjustment

12 Extension Cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and overheating. Table 1 shows the correc...

Page 15 - Basic Operations; Horizontal Sanding

15 Basic Operations Removing the belt guard exposes more of the sanding belt! Replace the belt guards immediately after completing any sanding that requires its removal! Failure to comply may cause serious injury! Horizontal Sanding For horizontal sanding , the platen is locked in the horizontal pos...

Page 16 - Contour Sanding

16 Contour Sanding Referring to Figure 19: Contour sanding is done from the extension table mounted on the motor where the sanding belt wraps around the drive drum (D). To set up the sander for contour sanding: 1. Loosen the two lock knobs (C) that secure the drum guard & dust port (E). 2. Swing...

Page 17 - Troubleshooting Operating Problems; Parts; Ordering Replacement Parts

17 Troubleshooting Operating Problems Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord Sanding belt does not com...

Page 18 - Table and Motor – Parts

18 Table and Motor – Parts Index No. Part No. Description Size Qty. 1............... EHVS80CS-01 .........Base...................................................................................................... 1 2............... EHVS80-02N ...........Push Button Switch ..............................

Page 19 - Sanding Belts

19 Table and Motor – Parts Index No. Part No. Description Size Qty. 53............. OES80CS-153 .........Pin......................................................................................................... 2 54............. EHVS80-67..............Motor Cord .....................................

Page 20 - Table and Motor – Assembly

Page 21 - Idle Drum – Parts

21 Idle Drum – Parts Index No. Part No. Description Size Qty. 1............... OES80CS-201 .........Tension Bar ........................................................................................... 1 2............... OES80CS-203 .........Spring.....................................................

Page 22 - Idle Drum – Assembly

Page 24 - Wiring Diagram

Jet OES-80CS - Manual

Table of Contents:

Summary

Other Jet Models