JAI CV-A60 - Manuals - manualsarea.com

Page 2 - DECLARATION OF CONFORMITY; AS DEFINED BY THE COUNCIL DIRECTIVE; Table of Contents

CV-A50 / CV-A60 DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPABILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROVISIONS APPLYING TO IT. EN-50081-1 EN-50082-1 Table of Contents 1. General......................................

Page 3 - Standard Composition

CV-A50 / CV-A60 1. General The difference from the previous manual is that the CCD sensor in CV-A50 is changed to new types. Now the used CCD sensors are: ICX-408AL-6, 409AL-6, 418ALL-6, 419ALL-6. The CV-A50/A60 is a range of monochrome CCIR and EIA interlaced 1/2” and 1/3” CCD cameras, designed for...

Page 4 - Camera Housing and Dimensions; Gain potentiometer for manual gain setting.

CV-A50 / CV-A60 4. Camera Housing and Dimensions Fig. 1. Locations and dimensions. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface. 4. Gain pot...

Page 5 - Pin configuration is compatible with EIAJ standard; Signal; Parallel with the BNC connector.; Remarks; Configurations

CV-A50 / CV-A60 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin configuration is compatible with EIAJ standard Pin no. Signal Remarks 1 GND 2 +12 V DC input 3 GND 4 Video output Parallel with the BNC connector. 5...

Page 7 - Functions and Operations; SM

CV-A50 / CV-A60 6. Functions and Operations Apart from the standard continuous operation, the CV-A50/60 features three external asynchronous trigger modes (edge pre-select, pulse width controlled and start/stop) and a special frame-delay readout mode. Long integration time mode is also supported. 6....

Page 12 - sec

CV-A50 / CV-A60 6.4. External Trigger Modes This camera has 5 external asynchronous trigger modes, which can be set by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. 3. Frame Delay read out mode. T...

Page 13 - Important notes on using this mode:

CV-A50 / CV-A60 6.5. Edge Pre-select Mode The leading edge of the trigger pulse initiates the exposure. The exposure time (accumulation time) is governed by the pre-defined shutter speed set by RS-232C. The resulting video is output as “odd field” for EIA and “even field” for CCIR, and appear 9H (EI...

Page 19 - Configuring the Camera; Communication setting.; Parameter

CV-A50 / CV-A60 7. Configuring the Camera 7.1. RS-232C control. All configuration of the A50/60 camera is done via the RS-232C port. The camera can be set up from a PC running terminal emulator software, or using JAI´s camera control software. Below is the description of the ASCII based short comman...

Page 22 - HD/VD input to 75Ohm terminated; , follow these steps

CV-A50 / CV-A60 7.4. Internal Switch and Jumper Settings. 7.4.1 HD/VD input-output selection In the default setting the camera will accept external HD/VD signals on pins 6 and 7 of the 12 pin Hirose connector. The composite video signal from the camera will be synchronized to an external HD/VD sourc...

Page 23 - Specifications

CV-A50 / CV-A60 8. Specifications Specifications CV-A50C CV-A60C CV-A50E CV-A60E Scanning system CCIR, 25 frames/sec. 625 lines, 2:1 Interlaced EIA. 30 frames/sec. 525 lines, 2:1 Interlaced Frame rate (Full frame) 50 Hz 59.94 Hz Line frequency 15.625 kHz 15.734 kHz Pixel frequency 14.1875 MHz 14.318...

Page 24 - Spectral Sensitivity; Relative Response; Note 2

CV-A50 / CV-A60 9. Spectral Sensitivity 400 500 600 700 800 900 Wave Length (nm) 1.0 0.8 0.6 0.4 0.2 0.0 Relative Response 1000 Fig. 30. Spectral sensitivity. 10. Appendix 10.1. CV-A50 or CV-A60 emulating CV-M50 interfacing The CV-A50 and CV-A60 have a slightly different pin configuration on the 12-...

Page 25 - WEN out on pin 6 on 6 pin connector; EEN out

CV-A50 / CV-A60 10.2. WEN out on pin 6 on 6 pin connector Instead of EEN output on pin #6 on the 6 pin Hirose connector, WEN can be output by jumper settings. The 2 jumpers are found on the main board PK8275B, if the bottom plate is removed. JP1 JP2 Signal on pin #6 JP1 JP2 Remark EEN out open short...