JAI VIS-CAM 400 - Manual

JAI VIS-CAM 400

JAI VIS-CAM 400 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
Page: / 44

Table of Contents:

  • Page 3 – Notice; and begins on the date of shipment from JAI stock.; Certifications; CE Compliance
  • Page 4 – WARNING; VIS-CAM System Installation Manual
  • Page 5 – Table of Contents
  • Page 7 – List of Figures
  • Page 9 – List of Tables; Table 1
  • Page 11 – In Image Triggering System; Introduction; Document Overview; from the JAI website.
  • Page 12 – VIS-CAM 350 IIT overview; Principle of Operation; Block Diagram of the IIT Camera
  • Page 13 – Camera front with beamsplitter and fibers; trigger is generated and an image is grabbed.; The sensitive region of the picture area
  • Page 14 – The system will only work
  • Page 15 – Preparing for installation; Preparation for installation; Over Lane Positioning; vandalism is a paramount concern.; Typical Over Lane Site Layout; between camera and license plate must be in between 10m and 20m.; Camera tilt considerations
  • Page 16 – Typical Over Lane Site Layout Plan; The Light Sensor and Flash shown in Figure 6 are optional.; Performance of Trigger and Light Sensor function
  • Page 17 – Installation; Camera Dimensions; IIT Camera Housing side view
  • Page 18 – Opening the Camera Housing; they can be turned by fingers. The screws are retained by springs.
  • Page 19 – Attaching the Safety Tether; Figure A
  • Page 20 – Cable Connections
  • Page 21 – IIT Camera I/O Board Layout
  • Page 22 – IIT I/O Board Power and Data Connector X2 signals; Connection to J-Panel and Power Supply
  • Page 23 – IIT I/O Board Flash Connector X1 signals
  • Page 24 – IIT Camera System Manual; Installation manual, also applies to the IIT Camera.; Signal Indicator LED positions
  • Page 25 – Select Manual Control in the Camera ADR Control
  • Page 26 – Set the value to 1.50 by manually typing the value; Properties setup when using External Light Sensor; Trigger Selection
  • Page 27 – Select Falling Edge in the Trigger Edge Select field; As described in the VIS-CAM System Installation manual section 4.
  • Page 28 – The field ALPR Enable must be set to “Enabled”.
  • Page 29 – ALPR Enabled; be Minimum 15 and Maximum 45.; ENSetup Image and LPR output Capture Mode
  • Page 30 – Capture Images setting
  • Page 31 – should not be enabled simultaneously in the camera.; Setting the IIT I/O Board internal trigger parameters; Serial Communication Terminal
  • Page 32 – IIT I/O Board communication; The DAC values in; commands C to J; are set to 32 from the factory and it is normally not necessary; command A; The minimum time between two trigger pulses are set by; command M; to a value between 01 and FF; command
  • Page 33 – IIT Camera Trigger Generation Principle
  • Page 34 – Appendix A: Troubleshooting
  • Page 35 – Appendix B: Focus Adjustment of Kowa 35mm; using IIT IR Illuminator for night illumination.; IR Illuminator connector; ) Adjust the focus on the lens to near position :; Kowa 35mm lens; holding down the “Alt” key and clicking anywhere in the picture)
  • Page 36 – IIT cameras. The picture below shows the VIS-CAM 400 IIT overview
  • Page 37 – Appendix D: Connection to TNC-100 Floodlight; Connection to TNC-100 for VIS-CAM 400 IIT
  • Page 38 – Appendix E: IIT I/O Board default settings
  • Page 41 – Appendix F: Quick Start Guide; Illustration; Find a place to mount; Mount the camera
  • Page 42 – Connect the camera to; Do not adjust
Loading the manual









IIT Camera Systems

In Image Triggering Cameras

VIS-CAM 350 IIT
VIS-CAM 400 IIT










Document Version: A

Document P/N: 10657

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Notice; and begins on the date of shipment from JAI stock.; Certifications; CE Compliance

Disclaimer iii IIT Camera System Manual Notice The material contained in this manual consists of information that is proprietary to JAI Inc., and may only be used by the purchasers of the product. JAI Inc. makes no warranty for the use of its product and assumes no responsibility for any errors whic...

Page 4 - WARNING; VIS-CAM System Installation Manual

IIT Camera System Manual iv Disclaimer WARNING Changes or modifications to this unit not expressly approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment. VIS-CAM System Installation Manual JAI Inc. 625 River Oaks Parkway San Jose, CA 95134 Tel:...

Page 5 - Table of Contents

Table of Contents v IIT Camera System Manual Table of Contents Disclaimer Notice ................................................................................................... iii Table of Contents ....................................................................................................

Other JAI Models

All JAI Other