Intel POD-6552 - Manuals

v FCC This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the following two conditions:1.This device may not cause harmful interfer-ence, and2. This device must accept any interference received, including interference that may cause undesired operationThis...

vii Contents Chapter 1 General Information ........................................2 1.1 Introduction ....................................................................... 2 1.2 Features ............................................................................. 2 1.3 Specifications ...............

1 Chapter 1 General Information 1 General Information This chapter gives background information on the POD-6552. Sections include: • Introduction• Features• Specifications• Board layout and dimensions CH AP T E R

POD-6552 User’s Manual 2 Chapter 1 General Information 1.1 Introduction The POD-6552 is a new Intel® Celeron® M 600 MHz(0L2) 5.25" Bis-cuit PC with enhanced graphics function. The POD-6552 comes with an embedded high-performance Celeron® M 600 MHz processor on-board, and one socket479 optional f...

3 Chapter 1 General Information 1.3 Specifications 1.3.1 Standard SBC Functions • CPU: Intel® Celeron® M 600 MHz w/o L2 cache. Socket479(Optional for Celeron® M and Pentium® M CPU) • System chipsets: Intel® 852GM/ICH4 • BIOS: Award 4Mbit Flash memory • System memory: One DDR SODIMM socket, support u...

POD-6552 User’s Manual 4 1.3.3 Solid State disk • Supports CompactFlash Type I/II disks 1.3.4 TV-Out • Chipset: Chrontel CH7009• Supports TV output• Supports NTSC and PAL formats• Supports s-video• TV output supports graphics resolutions up to 1024x768 pixels 1.3.5 Ethernet interface • Chipset: Real...

7 Chapter 2 Installation 2 Installation This chapter explains the setup procedures of POD-6552 hardware, including instruc-tions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all safety precautions before you begin the installation procedure. CH AP T E R

15 Chapter 2 Installation 2.9 SM BUS Connector(J6) 2.10 PCI VIO(J7) 2.11 Installing DDR SODIMMs The procedure for installing DDR SODIMMs appears below. Please follow these steps carefully.1. Make sure that all power supplies to the system are switched off2. Install the DDR SODIMM card. Install the D...

19 Chapter 2 Installation 2.16.4 TTL LCD/DSTN connector(CN17) CN17 is a 40-pin connector for TTL LCD or DSTN. It could connect TTL LCD or DSTN freely to meet your need. 2.17 USB connectors (CN4,CN11,CN12) The POD-6552 board provides up to six USB (Universal Serial Bus) ports. This gives complete Plu...

21 Chapter 2 Installation 2.21.6 Lan Active LED(Pin 7 & Pin 8) The LED would light when the Lan is active. 2.21.7 Lan Linked LED(Pin 9 & Pin10) The LED would light when the Lan is linked. 2.22 Audio interface 2.22.1 Audio connector(CN8) The Audio link is a 2x8 pin connector, the POD-6552can ...

CHAP T ER 3 Software Configuration This chapter details the software con-figuration information. It shows you how to configure the card to match your application requirements. Award System BIOS will be covered in Chapter 4.Sections include: • Introduction• VGA display software configuration

POD-6552 User’s Manual 24 Chapter 3 Software Configuration 3.1 Introduction The system BIOS and custom drivers are located in a 512 KB, 32-pin (JEDEC spec.) Flash ROM device, designated U28. A single Flash chip holds the system BIOS, VGA BIOS, and network Boot ROM image. The display can be configure...

25 Chapter 3 2. At the prompt, type AWDFLASH.EXE and press <Enter>. The VGA configuration program will then display the following: 3. At the prompt, enter the new BIN file which supports your display. When you are sure that you have entered the file name correctly press <Enter>. 4. The s...

27 Chapter 4 Ducks that Need Love! 4 Award BIOS Setup This chapter describes how to set BIOS configuration data. CH AP T E R

POD-6552 User’s Manual 28 Chapter 4 Award BIOS Setup 4.1 System test and initialization These routines test and initialize board hardware. If the routines encoun-ter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors...

29 4.2 Award BIOS setup Award’s BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. 4.2.1 Entering setup Power on the com...

POD-6552 User’s Manual 38 4.2.10 Set Password To Establish Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password,” enter the desired password and press <Enter>. 3. At the “Confirm Password” prompt, retype the d...

39 To Change Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password,” enter the existing password and press <Enter>. 3. You will see “Confirm Password.” Type it again, and press <Enter>. 4. Select Set Pass...

POD-6552 User’s Manual 40 To Disable Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password,” enter the existing password and press <Enter>. 3. You will see “Confirm Password.” Type it again, and press <Enter...

CHAP T ER 5 PCI SVGA Setup IntroductionInstallation of SVGA drivers -for Windows XP Further information

POD-6552 User’s Manual 44 Chapter 5 PCI SVGA Setup 5.1 Introduction The board has an onboard interface. The specifications and features are described as follows: 5.1.1 Chipset The POD-6552 uses a Intel 852GM + ICH4 chipset for its graphic con-troller. It supports LVDS LCD displays, conventional CRT ...

45 Chapter 5 5.2 Installation of the SVGA Driver Complete the following steps to install the SVGA driver. Follow the pro-cedures in the flow chart that apply to the operating system that you are using within your board. 5.2.1 Installation for Windows 2000/XP To install SVGA driver for Window 2000/XP...

POD-6552 User’s Manual 48 5.3 Further Information For further information about the AGP/VGA installation in your POD-6552, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Intel website: www.intel.com. Advantech websites: www.advantech.com www.advant...

49 Chapter 6 CHAP T ER 6 Audio Setup • Introduction• Installation of audio driver for Win- dows XP

POD-6552 User’s Manual 50 Chapter 6 Audio Setup 6.1 Introduction The POD-6552 supports AC97 stereo sound without Amplifier and sup-ports speaker-out, CD-input, Line-in, Line-out and Microphone.. 6.2 Driver installation 6.2.1 Before you begin Please read the instructions in this chapter carefully bef...

53 Appx. A A Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: • Floppy Drive Connector• Primary IDE Connector• LPT Connector• Secondary IDE(Slave) Connector• ATX Power Connector• COM3/COM4 output• USB0, 1 Connector• USB2, 3Connector• USB4, 5Connect...

POD-6552 User’s Manual 54 Appendix A Pin Assignments A.1 ATX power connector (CN23) Table A.1: ATX power connector(CN23) Pin Signal 1 5VSB 2 NC 3 PS_ON 1 2 3

71 Appx. B B System Assignments This appendix contains information of a detailed nature. It includes: • System I/O ports• 1st MB memory map• DMA channel assignments• Interrupt assignments Appe ndi x

POD-6552 User’s Manual 74 B.4 Interrupt assignments Table B.4: Interrupt assignments Interrupt# Interrupt source IRQ 0 Interval timer IRQ 1 Keyboard IRQ 2 Interrupt from controller 2 (cascade) IRQ 3 COM2 IRQ 4 COM1 IRQ 5 COM4 IRQ 6 FDD IRQ 7 LPT1 IRQ 8 RTC IRQ 9 Reserved (audio) IRQ 10 COM3 IRQ 11 R...

Pod-6552 User’s Manual 76 Appendix C Programming the Watchdog Timer C.1 Supported Input Timing Modes In order to program the watchdog timer, you must write a program which writes I/O port address 866 (hex). The output data is a value of time inter-val. The value range is from 01 (hex) to FF (hex), a...