Impex PHE 2000 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; please call our TOLL-FREE customer service number.; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…..............................................................

Page 3 - IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 4 - HARDWARE PACK

Page 7 - ASSEMBLY INSTRUCTION; DIAGRAM 1

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Middle Base Frame (#1) between the Front & Rear B...

Page 8 - DIAGRAM 2

STEP 2 (See Diagram 2) A.) Place two ∅ 2 ½” Rubber Bumpers (#65) on the Rear Base Frame (#2). Align the holes and insert Two Guide Rods (#18) through the holes into the Rear Base Frame. Secure each Guide Rod with one M10 x 1” Allen Bolt (#75) and ∅ ¾” Washer (#87) from the bottom of Rear Base Frame....

Page 10 - DIAGRAM 3

Page 11 - DIAGRAM 4

STEP 4 (See Diagram 4) A.) Attach two Diagonal Support Frames (#7) to the Front Base Frame (#3). Secure it with one M10 x 3” Carriage Bolt (#77), ∅ ¾” Washer (#87), and M10 Aircraft Nut (#89). B.) Secure the two Diagonal Supports to the Seat Support Frame (#6) with one M10 x 3” Carriage Bolt (#77), ...

Page 12 - DIAGRAM 5

STEP 5 (See Diagram 5) A.) Attach the Front Press (#11) to the pivot on the Front Press Base (#10). Align the holes and insert the Front Press Axle (#32) through the holes. B.) Secure each end of the Axle with one M10 x ¾” Allen Bolt (#76) and ∅ 1 3/8” Washer (#66). Secure the Axle to the Front Pres...

Page 13 - DIAGRAM 6

STEP 6 (See Diagram 6) A.) Attach the Butterfly Base (#14) to the Vertical Frame (#5). Secure it with one 4 ¾” x 2” Bracket (#26), two M10 x 3 ½” Carriage Bolts (#71), two ∅ ¾” Washers (#87), and two M10 Aircraft Nuts (#89). B.) Insert the Right Butterfly (#20) into the right pivot on Butterfly Base...

Page 14 - DIAGRAM 7

STEP 7 (See Diagram 7) A.) Place the Seat Pad (#21) onto the Seat Post (#9). Secure it with two M8 x 1 5/8” Allen Bolts (#82) and ∅ 5/8” Washers (#86). B.) Insert the Seat Post into the opening on the Seat Support Frame (#6). Use a Lock Knob (#44) to obtain the desired height of Seat. C.) Insert two...

Page 15 - CABLE LOOP DIAGRAM

Page 17 - DIAGRAM 8

Page 18 - Upper Cable Loop Diagram

Page 20 - DIAGRAM 9

Page 21 - Lower Cable Loop Diagram

Page 23 - Butterfly Cable Loop Diagram

Page 25 - WEIGHT RESISTANCE CHART; *Value for butterfly is for each arm.

WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Low Pulley 22 33 44 55 66 77 88 99 110 Lat Pull 30 40 50 60 70 80 90 100 110 Butterfly 10 16 22 28 34 40 46 52 58 Front Press 20 34 48 62 76 90 104 118 132 AB Crunch 22 33 44 55 66 77 88 99 110 Leg Developer 26 38 50 62 74 86 98 110 122 ...

Page 27 - LIMITED WARRANTY

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's...