Impex MWM 900 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; PARTS LIST...............................................................................................; BEFORE YOU BEGIN; Supplied by

2 TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 2 IMPORTANT SAFETY PRECAUTIONS.........................................................……….. 3 HARDWARE IDENTIFIER.....….........................................................

Page 3 - IMPORTANT SAFETY PRECAUTIONS; STOP; incorrect or excessive exercise.; This product is intended for H=Domestic use only.

3 IMPORTANT SAFETY PRECAUTIONS This gym built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or use your gym. In particular, note the following safety precautions: 1. Keep children and p...

Page 4 - HARDWARE PACK

Page 7 - ASSEMBLY INSTRUCTION

7 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A) Slide two Ø2 ½” Round Rubber Bumpers (#43) onto the Guide ...

Page 8 - DIARGRAM 1

Page 10 - Attach two; DIAGRAM 3

STEP 3 (See Diagram 3) A) Place the Seat (#55) onto the Seat Support (#10). Secure it with two M8 x 1 5/8” Allen Bolts (#69) and Ø 5/8” Washers (#78). B) Insert the Seat Support into the opening on the Main Base Frame (#1). Use a Lock Knob (#32) to secure the Seat Support at desired height. C) Attac...

Page 11 - DIAGRAM 4

STEP 4 (See Diagram 4) A) Attach the Front Press Base (#3) to the Upper Frame (#6). Secure it with one Axle (#24), two Spacers (#79), and two M10 Aircraft Nuts (#81). Do not over tighten the Nuts. B) Insert the axle on the Right Butterfly (#4) through the hole on the Front Press Base from the bottom...

Page 12 - CABLE LOOP DIAGRAM

Page 14 - DIAGRAM 5

Page 15 - STEP 6 (See Diagram 6 & Cable Loop Diagram; Install another Pulley as described in Step B above.

STEP 6 (See Diagram 6 & Cable Loop Diagram A) Attach one end of the 108” Butterfly Cable (#58) to the hook on the Right Butterfly (#4). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B) Attach a Pulley (#41) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#65), two ...

Page 16 - installed in Step 6. Repeat Step D to install another Pulley.

16 STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 144” Lower Cable (#59) to the opening on the bottom of the Leg Developer (#9). B. ) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two ∅ 7/8” Pulley Bushings (#35), and one M10 Aircraft Nut (#81)...

Page 17 - DIAGRAM 7

Page 18 - NO DESCRIPTION QTY

18 PARTS LIST KEY NO DESCRIPTION QTY 1. Main Base Frame 1 2. Vertical Beam 1 3. Front Press Base 1 4. Right Butterfly 1 5. Left Butterfly 1 6. Upper Frame 1 7. Guide Rod 2 8. Rear Stabilizer 1 9. Leg Developer 1 10. Seat Support 1 11. Lat Bar 1 12. Arm Curl Handle 1 13. Arm Curl Tube 1 14. Double Fl...

Page 20 - LIMITED WARRANTY; Your statutory rights are not affected.

20 LIMITED WARRANTY Escalade warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the frame and one year on all other parts and components from the date of purchase. This warranty extends only to the original...

Page 21 - CARE AND MAINTENANCE; Inspect and tighten all parts before using the gym.

21 . CARE AND MAINTENANCE 1. Inspect and tighten all parts before using the gym. 2. The gym can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents. 3. Examine the gym regularly for signs of damage or wear. Pay particular attention to the bushings on movable parts. 4. ...