Husky 647016 - Manuals

Husky 647016 – Manual in PDF format online.

Manuals:

Manual

Manual Husky 647016

Summary

Page 2 - Contents; Manual Description

Related Manual 2 313597E Contents Related Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 To Order a New Pump: . . . . . . . . . . . . . . . . . . . . . . 3 To Order Parts for Your Existing Pump . . . . . . . . . 3 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - To Order Parts for Your Existing Pump

To Order a New Pump: 313597E 3 To Order a New Pump: NOTE: Do not configure and order a pump using only this manual. Work with your Graco distributor or follow the steps below. 1. Go to www.gracohusky.com. 2. Click on Toolbox in the gray banner near the top. 3. Click on the Husky 1050 Pump Selector, ...

Page 4 - TP

Models 4 313597E Models UL Listing Details Models 647016 and 647648 are certified per UL 79 for use in pumping gasoline andgasoline/alcohol blends up to 10% ethanol, diesel fuel, fuel oil, and lubricating oil. Thiscertification does not cover oil burner pumps; pumps for engine-powered automotive equ...

Page 5 - Warnings; WARNING; Use equipment only in well ventilated area.; Ground all equipment in the work area. See Grounding instructions.; Use only grounded hoses.

Warnings 313597E 5 Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equip-ment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. When these symbols appear in the body of this manual...

Page 6 - Do not alter or modify equipment.

Warnings 6 313597E EQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all eq...

Page 7 - Read MSDS’s to know the specific hazards of the fluids you are using.

Warnings 313597E 7 TOXIC FLUID OR FUMES HAZARDToxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.• Read MSDS’s to know the specific hazards of the fluids you are using. • Route exhaust away from work area. If diaphragm ruptures, fluid ma...

Page 8 - Installation; General Information

Installation 8 313597E Installation General Information • The Typical Installations shown in F IG . 3 through F IG . 5 are only guides for selecting and installing system components. Contact your Graco distributor for assistance in planning a system to suit your needs. • Installation and use must be...

Page 9 - Fluid supply container: Follow local code.; Air Line

Installation 313597E 9 Air and fluid hoses: Use only grounded hoses with a maximum of 500 ft (150 m) com-bined hose length to ensure groundingcontinuity. Air compressor: Follow manufacturer’srecommendations. Fluid supply container: Follow local code. Solvent pails used when flushing: Follow local co...

Page 10 - Air Exhaust Ventilation; Place a container at the end of the air

Installation 10 313597E Air Exhaust Ventilation The air exhaust port is 3/4 npt(f). Do not restrict the air exhaust port. Excessive exhaust restriction can cause erratic pump operation. 1. Remove the muffler (T) from the pump air exhaust port. 2. Install a grounded air exhaust hose (U) and connect t...

Page 11 - Fluid Supply Line; . 3. Waste oil or general fluid transfer, typical installation

Installation 313597E 11 Fluid Supply Line See F IG . 3 through F IG . 5, pages 11 through 13. 1. Use grounded, flexible fluid supply lines (G). See Grounding, page 8. 2. If the inlet fluid pressure to the pump is more than 25% of the outlet working pres-sure, the ball check valves will not close fas...

Page 12 - Fluid Outlet Line; See F; Fluid Inlet and Outlet Ports

Installation 12 313597E Fluid Outlet Line See F IG . 3 through F IG . 5, pages 11 through 13. 1. Use grounded fluid hoses (G, K). See Grounding, page 8. 2. The pump fluid outlet is 1 in. npt(f). Screw the fluid fitting into the pump outlet securely. 3. A fluid drain valve (H) is required in your sys...

Page 14 - Fluid Pressure Relief Valve; Evacuation and Transfer Systems (Model 647016); (not acceptable for fuel dispense application)

Installation 14 313597E Fluid Pressure Relief Valve Fuel Dispense Systems (Model 647648) Evacuation and Transfer Systems (Model 647016) Fuel dispense model 647648 requires a pres-sure relief valve (S), Graco part 24B910, which is supplied with the pump, to prevent fluid pressure from exceeding 50 ps...

Page 15 - Operation; Pressure Relief Procedure

Operation 313597E 15 Operation Pressure Relief Procedure 1. Shut off the air supply to the pump. 2. Open the dispensing valve (if used). 3. Open the fluid drain valve to relieve fluid pressure, having a waste container ready to catch the drainage. Flush the Pump Before First Use The pump was tested ...

Page 16 - Gear Oil Evacuation Systems; Fuel Dispense Systems; Pump Shutdown

Operation 16 313597E Gear Oil Evacuation Systems See F IG . 4. 1. Close the pump air regulator (C) and the bleed-type master air valves (B, E). 2. Attach an appropriate wand to the suction hose. Place the wand in the differential or fluid to be pumped. 3. Place the end of the fluid hose into an appr...

Page 17 - Maintenance; Maintenance Schedule; • Flush before fluid can dry in the equipment,

Maintenance 313597E 17 Maintenance Maintenance Schedule Establish a preventive maintenance schedule, based on the pump’s service history. Sched-uled maintenance is especially important to prevent spills or leakage due to diaphragmfailure. Lubrication The pump is lubricated at the factory. It is desi...

Page 18 - Torque Instructions

Maintenance 18 313597E Torque Instructions NOTE: Fluid cover and manifold fasteners have a thread-locking adhesive patch applied to the threads. If this patch is excessively worn, the fasteners may loosen during operation. Replace screws with new ones or apply medium-strength (blue) Loctite or equiv...

Page 19 - Dimensions

Dimensions 313597E 19 Dimensions 5.0 in. 5.5 in. (140 mm) (127 mm) & % E A 1 0 3 / G F D ti14540a K J H ti12212b ti12211b ti12213b A ..... 12.7 in. (323 mm) B ..... 14.4 in. (366 mm) C ..... 15.9 in. (404 mm) D ..... 10.9 in. (277 mm) E ..... 1.8 in. (46 mm) F...... 7.3 in. (185 mm) G ..... 14.7...

Page 20 - Performance Chart; Test Conditions: Pump tested in water with inlet submerged.; Fluid Pressure

Performance Chart 20 313597E Performance Chart Test Conditions: Pump tested in water with inlet submerged. 0 5 10 15 20 25 30 35 40 45 50 (19) (38) (57) (76) (95) (114) (133) (152) (170) (189) Fluid Out let Pre s s u re — ps i ( M Pa, bar) A B C 0 5 10 15 20 25 30 35 40 45 50 (19) (38) (57) (76) (95...

Page 21 - Technical Data

Technical Data 313597E 21 Technical Data * Sound power measured per ISO-9614-2.** Sound pressure was tested 3.28 ft (1 m) from equipment. All trademarks mentioned in this manual are the property of their respective owners. Maximum fluid working pressure Transfer Pump . . . . . . . . . . . . . . . . ...

Page 22 - Graco Standard Husky Pump Warranty

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 313597 Graco Headquarters: Minneapolis Int...