Husky 16628 - Manual
Husky 16628 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – framing. This requires you to add the following material:
- Page 3 – FLOOR PANEL ATTACHMENT:; With Floor Panels flush to
- Page 4 – Mark the 88” Board as shown at 28” then another; SHELF PANEL INSTALLATION:; Install the shelf frame resting on the horizonal Back
1
COMBINATION 8X8 and 10X8 FLOOR KIT
This floor kit will build either the 10’ wide or 8’ wide x 7’ 8-5/8” deep floor size
This floor kit is for 10’ x 7’ 8-5/8” and 8’ x 7’ 8-5/8” buildings. Please refer to the appropriate pages
of this instruction manual to build the floor size needed. If constructing an 8X8 storage building,
you will have additional material which can be used to construct a shelf (some cutting required)
or other projects.
07/31/2006
#16628
Important!
Please follow these instructions. This kit may be different from the one specified in instruction booklet.
- B E F O R E Y O U B E G I N -
First...
Read these instructions thoroughly before you begin
assembly. Assembly is easiest if you follow the steps in
the order shown.
Lumber is graded from only one side. Check the part for
the most attractive face and make sure to face it to the
outside.
Check all parts
Compare parts you have to the list on page 2. If a part is
missing, circle the part in question in the parts list and
call us toll-free at 1-800-437-0784.
Assistance required
We recommend that you assemble this floor on level
ground in the location it will be used. Assistance is
necessary to handle, fit, and secure some components.
Two people maybe needed for some steps.
Squareness is very Important!
Keeping all 90° corners and 90° perpendiculars square
throughout the assembly of this floor kit will make each
succeeding step easier and is necessary to assure that
all components fit together properly.
Check local zoning
Before starting construction, check with your local
building code official for any required permits, variances,
etc.
Check floor kit size
Before starting construction on your floor, make sure
that you check in the instruction manual to ensure that
you are building the correct size floor kit for your
building.
Always wear OSHA-APPROVED safety
glasses throughout assembly process
■
Tools required
❑
Hammer
❑
Level
❑
Pencil
❑
Tape Measure
■
Optional tools
❑
Chalk Line
❑
Square
❑
Nail Pouch
❑
Saw
8 x 8
See pages 2-3-4
FOR MARCO SERIES, SOLAR SHED AND MWP IMPERIAL ONLY
10x8
See pages 5-6
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 B A Y Y X X (2) 3" Nails 24" (61 cm) 24" (61 cm) 24" (61 cm) 24" (61 cm) 92-5/8" (4) 3" Nails at Joint 96" (244 cm) Center of Stud Center of Stud C C C D C C D D D F F F F L O O R K I T I N S T R U C T I O N SFOR 8X8 BUILDINGS ACTUAL SIZE 96” WIDE x 92-5/8” DEEP A: ...
3 Nails every 12" (30 cm) through Floor Panels into all Floor Bond Boards and Floor Joists D C C D A A A F D F 92-5/8" 96" 24" (61 cm) 24" (61 cm) FLOOR PANEL ATTACHMENT: C: Position a 48 x 92-5/8” Floor Panel flush to the outsideedges of sides and back ofFloor Frame. Secure pane...
4 8X8 OPTIONAL SHELFI N S T R U C T I O N S 1 - 23-7/8x92-5/8x5/8" Floor Panel1 - 2x4x89-1/2" Floor Joist2 - 2x4x48" Bond Boards - 2" and 3" Nails B C E Parts needed to cut: (1) - 89-1/2" Board cut down to 88" 88" (2) - 48" Board cut down to 2 pieces of 24-11/16 a...
