Page 2 - Listing Label Information/Location; We recommend that you record the following pertinent; Homeowner Reference Information; Read this manual before installing or operating this appliance.; NA; XXXXXXXX
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fireplace: ____...
Page 3 - Safety Alert Key:; Used to address practices not related to personal injury.; Table of Contents; User Guide
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious i...
Page 6 - B. Limited Lifetime Warranty
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 6 4021-645C 12-29-10 Page 2 of 2 WARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT b...
Page 7 - Direct Vent Gas Appliance Heater; A. Appliance Certification; NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.; This appliance is tested and approved as either supplemen-; D. High Altitude Installations; Listing and Code Approvals; Models
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 7 B. Tempered Glass Specifications Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous loca- tions such as bathtub enclosures as defined by the Con- sumer Product Safety ...
Page 8 - E. Non-Combustible Materials Specification; Standard Test Method for Behavior of Materials in a; F. Combustible Materials Specification; This appliance must be electrically wired and; National Electric Code ANSI/NFPA; or the; Canadian Electric Code CSA
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 8 E. Non-Combustible Materials Specification Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof....
Page 9 - NOT; The following requirements referenc e var ious
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 9 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, includ...
Page 10 - WARNING! DO NOT operate fireplace before read; A. Gas Fireplace Safety; WARNING; This appliance has been supplied with an integral barrier; HOT SURFACES; Operating Instructions
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 10 Figure 2.1 General Operating Parts B. Your Fireplace WARNING! DO NOT operate fireplace before read - ing and understanding operating instructions. Failure to operate fireplace according to operating instructions could ca...
Page 11 - F. Fixed Glass Assembly; This fireplace has been supplied with an integral; G. Remote Controls, Wall Controls and Wall
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 11 D. Clear Space WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or...
Page 12 - J. Before Lighting Fireplace; have a; WARNING! Risk of Fire or Asphyxiation! DO NOT; I. Control Module Operation; Module Reset; ule more than one time within a five minute time period.; H. IPI Battery Tray/Battery Installation; Batteries should only be used as a power source; Nine Hour Safety Shutdown Feature
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 12 J. Before Lighting Fireplace Before operating this fireplace for the first time, have a qualified service technician : • Verify all shipping materials have been removed from inside and/or underneath the firebox. • Review...
Page 13 - NOT FOR USE; GAS; WHAT TO DO IF YOU SMELL GAS; DO NOT CONNECT LINE VOLT-; Also Certified for Installation in a; Final inspection by
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 13 K. Lighting Instructions (IPI) 1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand. 2. Wait five (5) minutes to clear out any gas. Then smel...
Page 14 - DO NOT CONNECT 110 VAC TO
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 14 L. Lighting Instructions (Standing Pilot) 1. Turn off all electric power to the appliance if ser- vice is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob sligh...
Page 15 - M. After Fireplace is Lit; ISSUE
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 15 Initial Break-in Procedure• The fireplace should be run three to four hours continuously on high. • Turn the fireplace off and allow it to completely cool.• Remove fixed glass assembly. See Section 14.H.• Clean fixed gla...
Page 16 - Glass Cleaning; Tools Needed; CAUTION! Handle fixed glass assembly with care.; Note; Maintenance and Service; The fireplace should be turned; Tools needed; Remote Control; Any safety screen or guard removed for servicing must be
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 16 Glass Cleaning Frequency: Seasonally By: Homeowner Tools Needed : Protective gloves, glass cleaner, drop cloth and a stable work surface. CAUTION! Handle fixed glass assembly with care. Glass is breakable. • Avoid striki...
Page 17 - DO NOT
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 17 Venting Frequency: Seasonally By: Homeowner Tools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc. • Veri...
Page 18 - C. Refractory, Grate and Valve Assembly; It may become necessary to remove the refractory, grate; do not; need to be removed to service the burner; BASE REFRACTORY; The base refractory must be
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 18 Figure 3.1 IPI Pilot Flame Patterns Figure 3.2 Standing Pilot Flame Patterns C. Refractory, Grate and Valve Assembly Removal It may become necessary to remove the refractory, grate and valve assemblies. This task should ...
Page 19 - NOTCH LOCATION
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 19 Figure 3.5 Valve Assembly Removal NOTCH LOCATION NG LP 6000C 6000CL 6000CLX 6000CBV 8000C 8000CL 8000CLX 8000CBV Figure 3.6 Burner Identification D. Burner Identification/Verification The burner may be accessed for ident...
Page 20 - A. Typical Appliance System; drawn to scale. Actual product may vary from pictures in manual; Dual venting c onf igurations; ARE NOT; allowed. Appliance; MUST; b e ve nte d; E I T H E R; ve r t i c a l l y; O R; Getting Started; Installer Guide
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 20 A. Typical Appliance System NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual ...
Page 21 - Read all of the instructions before starting the instal-; DO NOT i; C. Tools and Supplies Needed; Hearth & Home Technologies disclaims any responsibility for,; Any such action may cause a fire hazard.; DO NOT; Improper installation, adjustment, alteration, service or
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 21 B. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No ...
Page 22 - Framing and Clearances; A. Selecting Appliance Location; When selecting a location for the appliance it is important to; Mantel Projections
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 22 5 Framing and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). WARNING! Risk of Fire or Burns! Provide ...
Page 23 - B. Constructing the Appliance Chase
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 23 B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase. NOTICE: Treatment o...
Page 24 - D. Mantel and Wall Projections; Comply with all minimum clear-; Combustible Mantels; Measurement is taken from top of the
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 24 D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncom- bustible mate...
Page 25 - A. Vent Termination Minimum Clearances; Termination Locations; pack air space with insulation or other
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 25 A. Vent Termination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/1...
Page 26 - regulator; public; Covered Alcove Applications; Termination caps are HOT,
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 26 Figure 6.3 Minimum Clearances for Termination O N P R Q X = AIR SUPPLY INLET A = 12 inches.................clearances above grade, veranda, porch, deck or balcony B = 12 inches.................clearance to window or door...
Page 27 - WARNING! Risk of Fire or Asphyxiation.; Vent Information and Diagrams; D. Measuring Standards; Horizontal
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 27 A. Approved Pipe This appliance is approved for use with Hearth & Home Technologies DVP or SLP venting systems. Refer to Sec- tion 16B for vent component information. DO NOT mix pipe, fittings or joining methods from...
Page 29 - Three Elbows; Two Elbows; Minimum
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 29 H 2 H 1 V 2 V 1 Figure 7.5 Top Vent - Horizontal Termination - (continued) Three Elbows V 1 Min. H 1 Max. V 2 Min. H 2 Max. Elbow only 2 ft. 610 mm 0 in. 0 mm 1 ft. 305 mm 6 in. 152 mm 3 ft 914 mm 6 in. 152 mm 2 ft. 610 ...
Page 30 - Top Vent - Vertical Termination; If installing a vertical vent/; Flue Restrictor Instructions; Remove exhaust shield using a 1/4 inch nut driver by; Break the flue restrictor into two pieces. Do this by; BREAK
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 30 EXHAUST SHIELD FLUE RESTRICTOR Top Vent - Vertical Termination No Elbow Figure 7.6 Note: If installing a vertical vent/ termination off the top of the ap- pliance, the flue restrictor should be used. V 1 V 1 = 40 ft. Max...
Page 31 - Maximum
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 31 H 1 V 1 V 2 Top Vent - Vertical Termination (continued) Figure 7.11 Two Elbows Figure 7.10 4. Center the Flue Restrictor on vent and secure in place by using two self-tapping screws (see Figure 7.10). 5. Reinstall the Ex...
Page 32 - Minimum H; Elbow only
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 32 Figure 7.12 Top Vent - Vertical Termination - (continued) Three Elbows INSTALLED HORIZONTALLY H 1 H 2 V 1 V 2 V 1 H 1 + H 2 V 2 V 1 + V 2 Minimum H 1 + H 2 Maximum Elbow only 1 ft. 305 mm * * * 1 ft. 305 mm 6 in. 152 mm ...
Page 33 - Do not use a 45o elbow in corner installations.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 33 H 1 Rear Vent - Horizontal Termination Figure 7.14 No Elbow One 45º Elbow H 1 H 1 = 16 in. (406 mm) Maximum Do not use a 45º elbow in corner installations. Use two 90º elbows instead. Figure 7.13
Page 34 - Back to Back
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 34 INSTALLED HORIZONTALLY H 3 H 1 H 2 V 1 Rear Vent - Horizontal Termination - (continued) Two Elbows Figure 7.15 Figure 7.16 Three Elbows H 1 H 2 V 1 H 1 Maximum V 1 Minimum H 2 H 1 + H 2 Maximum 1 ft. 305 mm Back to Back ...
Page 35 - Back to Back 90o Elbows
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 35 Rear Vent - Vertical Termination One Elbow Figure 7.17 Two Elbows Figure 7.18 H 1 V 1 INSTALLED HORIZONTALLY H 1 H 2 V 1 V 1 Minimum H 1 Maximum 6 in. 152 mm 2 ft. 610 mm 1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 5 ft. 1.5 ...
Page 36 - *No specific restrictions on this value EXCEPT
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 36 Rear Vent - Vertical Termination - (continued) Three Elbows Figure 7.19 Three Elbows Figure 7.20 INSTALLED HORIZONTALLY H 3 H 1 H 2 V 1 V 2 V 1 H 2 H 1 H 1 H 2 H 3 V 1 Minimum H 1 + H 2 + H 3 Maximum * * * 8 ft. 2.4 m 6 ...
Page 37 - Coaxial to colinear venting; Coaxial to Colinear Venting; CLEARANCE TO COMBUSTIBLES REQUIREMENTS; Exhaust Vent Pipe; CAUTION! DO NOT use any flue restrictor when vent
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 37 EXHAUST VENT PIPE INLET AIR VENT PIPE Figure 7.21. Coaxial/Colinear Appliance Connector OUTSIDE FACE OF FIREPLACE TOP OF FIREPLACE OPENING SHADED AREA DEFINED AS “INSIDE EXISTING MASONRY FIREPLACE” 3 IN. MIN. 5 IN. MIN. ...
Page 38 - TOP VENT; To achieve optimum perfor-; Rear Vent; Do NOT connect this gas appliance to a chimney flue
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 38 Figure 7.23 EXISTING CHIMNEY HEARTH FLOOR EXISTING CHIMNEY EXHAUST AIR VENT PIPE INLET AIR VENT PIPE To minimize cold air drafts, seal with non-combustible insulation. TERMINATION CAP DIRECT VENT FIREPLACE V DVP-2SL COAX...
Page 39 - A. Pipe Clearances to Combustibles; Maintain air space clearance to; Vent Clearances and Framing; B. Wall Penetration Framing; Combustible Wall Penetration
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 39 A* B* 10 in. 12 in. C D 10 in. 12 in. A. Pipe Clearances to Combustibles WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling firestops • Between wa...
Page 40 - C. Install the Ceiling Firestop; lation around the vent. Insulation must be kept
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 40 C. Install the Ceiling Firestop A ceiling firestop MUST be used between floors and attics.• DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/floor (see Figure 8....
Page 41 - D. Install Attic Insulation Shield; Flat Ceiling Installation; Gas Kit; Vaulted Ceiling Installation
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 41 D. Install Attic Insulation Shield WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z2...
Page 42 - Appliance Preparation; Once the seal cap has been removed it CANNOT
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 42 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be chan...
Page 44 - HEADER; D. Securing and Leveling the Appliance
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 44 Figure 9.14 Proper Positioning and Securing of an Appliance NAILING TABS (BOTH SIDES) PILOT HOLES Figure 9.12 Non-combustible Board C. Installing the Non-combustible Board The factory supplied non-combustible board spans...
Page 45 - Attach Vent to the Firebox Assembly; The end of the pipe sections with the lanced tabs will face; Assemble Pipe Sections; WARNING! Risk of Fire or Explosion! DO NOT; Make sure that the seams are not aligned to prevent; INCORRECT; Lances
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 45 10 Installing Vent Pipe (DVP and SLP Pipe) A. Assemble Vent Sections (DVP Pipe Only) Attach Vent to the Firebox Assembly Note: The end of the pipe sections with the lanced tabs will face toward the appliance. Attach the ...
Page 46 - then rotate counterclockwise to lock; C. Assemble Slip Sections; Pilot hole
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 46 B. Assemble Vent Sections (SLP Pipe Only) To attach the first vent component to the starting collars of the appliance:• Attach a DVP-2SL or DVP-SLP24 adapter to the starting collar of the appliance. • Lock the vent compo...
Page 47 - E. Disassemble Vent Sections; Improper support may allow vent to sag and separate.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 47 120º Figure 10.8 Securing Vertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble Vent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned a...
Page 48 - F. Install Decorative Ceiling Components; rating
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 48 F. Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a flat ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the firestop.• Seal the...
Page 49 - G. Install Metal Roof Flashing; H. Assemble and Install Storm Collar; Wear protective gloves and safety glasses during instal-; Failure to properly caulk the roof flashing and; CAULK
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 49 G. Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. • Slide the roof flashing over the pipe sections extending th...
Page 50 - I. Install Vertical Termination Cap; Heat shields may; K. Heat Shield Requirements for Horizontal; To prevent overheating and fire,
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 50 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.18 TERMINATION CAP I. Install Vertical Termination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section whi...
Page 51 - L. Install Horizontal Termination Cap (DVP; Cap Specification Chart
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 51 Figure 10.20 Venting through the wall INTERIOR HEAT SHIELD OR EXTENDED HEAT SHIELD WALL SHIELD FIRESTOP HEAT SHIELD 1-1/2 IN. (38 MM) MIN. OVERLAP SHEATHING VENT DEPTH FROM BACK OF APPLIANCE TO OUTSIDE SURFACE OF EXTERIO...
Page 52 - Gas Information; Gas Pressure; • If substituting for these components, please consult
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 52 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts. B. Gas ...
Page 53 - C. Standing Pilot Ignition System Wiring; National Electric Code; B. IntelliFire PlusTM Ignition System Wiring; WARNING! Risk of Shock or Explosion! DO NOT; D. Optional Accessories Requirements; Electrical Information
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 53 Figure 12.1 Ignitor Button C. Standing Pilot Ignition System Wiring • The standing pilot ignition system wiring does not require a 110 VAC supply to operate. See Figure 12.3 • A 110 VAC junction box MUST be installed for...
Page 55 - F. Junction Box Installation; INSIDE; E. Electrical Service and Repair
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 55 G. Wall Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.5):• The power supply for the appliance must be brought into a switch box. • The power c...
Page 56 - Finishing; A. Mantel and Wall Projections
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 56 13 Finishing A. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances as specified. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materials (i....
Page 57 - Halston; Inch Thick or Less; Remove finishing strips before firing appliance.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 57 Figure 13.4 Finishing Material 1 Inch Thick or Less DOOR FIT FINISH MATERIAL THICKNESS SEE FIGURE Folio Inside Any 13.6 Arcadia Overlap 1 inch or less 13.4 Inside Greater than 1 inch 13.5 Halston Overlap 1 inch or less 1...
Page 58 - Finishing Material Thickness:
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 58 DOOR FINISHING MATERIAL FINISHING MATERIAL C (Includes 1/8 in. opening each side of door) A (Outside door width) Finishing material thickness, 1-4 inches maximum B = Top of door to bottom of fireplace. D = Bottom of Fini...
Page 59 - FINISHING STRIPS REMOVED; Removal of Finishing Strips
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 59 FINISHING STRIPS REMOVED Figure 13.7 Removing Finishing Strips. 31-7/8 IN. (6000) 33-11/16 IN. (8000) 3-3/4 IN. (6000, 8000) 35-5/16 IN. (6000) 43 IN. (8000) Figure 13.8. Clean Face Door Dimensions Removal of Finishing S...
Page 60 - D. Elevated Hearth Systems; stallation dimensions.; Note 2. Verify Marble Cut Lengths on site prior to cutting.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 60 D. Elevated Hearth Systems Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions. Some hearth systems will elevate the appliance off the ...
Page 61 - WARNING! Risk of Fire and Electric Shock!; Appliance Setup; E. Burner Top Installation
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 61 A. Remove Fixed Glass Assembly See Section 14.H. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the firebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated...
Page 62 - G. Install the Log Assembly; : Locate log placement tabs on the pilot cover. Bend; toward the left until it rests against the far left grate tine.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 62 G. Install the Log Assembly Log Assembly: LOGS-6C CAUTION: Logs are fragile, handle with care. Log #1 (SRV2164-701) : Locate log placement tabs on the pilot cover. Bend tabs upward as shown in Figure 2. Locate the log pl...
Page 63 - securely against right hand side of log indentation.; RIGHT GRATE TINE; FLAT AREA
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 63 Figure 7 2 3 1 Log #3 (SRV2164-703) : Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1. After slot and tab have been fitted together, mate the groove located on the bottom o...
Page 65 - the far left grate tine as well as contact Log # 2.
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 65 Figure 7 2 3 1 1 2 3 4 Figure 8 Figure 9 Figure 10 1 1 2 2 3 3 4 5 5 6 4 Log #3 (SRV2168-703) : Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1. After slot and tab have bee...
Page 66 - H. Fixed Glass Assembly; Removing Fixed Glass Assembly; Air Shutter Settings; J. Air Shutter Setting; NG
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 66 Figure 14.5 Air Shutter Figure 14.4 Fixed Glass Assembly H. Fixed Glass Assembly WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass fo...
Page 67 - A. Standing Pilot Ignition System; Troubleshooting; Symptom
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 67 A. Standing Pilot Ignition System 15 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshootin...
Page 69 - B. IntelliFire PlusTM Ignition System; there is no noise or
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 69 B. IntelliFire Plus™ Ignition System Symptom Possible Cause Corrective Action 1. Pilot won’t light. The ignitor/module makes noise, but no spark. A. Incorrect wiring. Verify “S” wire (white) for sensor and “I” wire (oran...
Page 70 - Reference Materials; A. Appliance Dimension Diagram; Location Inches
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 70 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.1 Appliance Dimensions-6000 Mo...
Page 72 - B. Vent Components Diagrams
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 72 10-1/2 in. (267 mm) 10-7/8 in. (276 mm) 45 ° 7-3/8 in. (187 mm) 11-3/8 in. (289 mm) 1-1/4 in. (32 mm) 9-1/4 in. (235 mm) 13-1/4 in. (337 mm) 1/2 in. TYP DVP90ST (90° Elbow) 10 in. (254 mm) 10 in. (254 mm) 1 in. (25 mm) 1...
Page 73 - Horizontal Termination Cap; Max; The heat shield is designed to be; Heat; continued
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 73 DVP-HPC1 DVP-HPC2 DVP-TRAP1 DVP-TRAP2 DVP-HPCK1-B DVP-HPCK2-B DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal Termination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST over...
Page 75 - DVP High Performance Cap
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 75 DVP-TB1 BasementVent Cap 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 7-1/4 in. 12 in. 305 mm (184 mm) 5-1/4 in. (133 mm) 12-1/2 in. (318 mm) DVP-TVHW VerticalTermination Cap (...
Page 76 - Power Vent Inline
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 76 Optional Wire Harness DESCRIPTION PART NUMBER 10 ft. PV Wire Harness PVI-WH10 20 ft. PV Wire Harness PVI-WH20 40 ft. PV Wire Harness PVI-WH40 60 ft. PV Wire Harness PVI-WH60 80 ft. PV Wire Harness PVI-WH80 100 ft. PV Wir...
Page 77 - HORIZONTAL TERMINATION CAP; Flex Liner Kit; COAXIAL to COLINEAR VENTING
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 77 B. Vent Components Diagrams (continued) DVP-HRC-SS DVP-HRC-ZC-SS HORIZONTAL TERMINATION CAP 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) 10-7/8 in. 276 mm 10-1/2 in. 267 mm 3° 87° Effective Length 5-3/4 to 8-3/8 in...
Page 78 - Effective Height/Length
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 78 B. Vent Components Diagrams (continued) Figure 16.8 SLP Series Vent Components Effective Height/Length Pipe inches mm SLP4 4 102 SLP6 6 152 SLP12 12 305 SLP24 24 610 SLP36 36 914 SLP48 48 1219 SLP6A 2 - 6 51 - 152 SLP12A...
Page 79 - Extended Heat Shield; Adapter
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 79 B. Vent Components Diagrams (continued) Figure 16.9 SLP Series Vent Components SLP-WT-BK Wall Thimble-Black 26 in. 660 mm DVP-HSM-B Extended Heat Shield SLP-TRAP Horizontal Termination Cap 15-1/8 in. (384 mm) Note: Heat ...
Page 81 - ITEM; Additional service part numbers appear on following page.; 6” Gas Fireplace - DV; Log Set Assembly; Beginning Manufacturing Date: Aug 2009
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 81 Service Parts IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an au...
Page 82 - 2” Gas Fireplace - DV
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 82 Service Parts IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an au...
Page 84 - Pilot Tube
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 84 Service Parts IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an au...
Page 86 - D. Contact Information; For the location of your nearest Heat & Glo dealer,; DO NOT DISCARD THIS MANUAL; NOTICE
Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12 86 D. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com. - NOTES - __________________________...
Heat & Glo SL-550TV-IPI-E
Manual
Heat & Glo CF750ENH
Manual
Heat & Glo ST-HV-IPI
Manual
Heat & Glo 6000GLX-IPILP-S/-R
Manual
Heat & Glo st-42tvfl
Manual
Heat & Glo 7000XLS
Manual
Heat & Glo 8000TV-OAK-IPI
Manual
Heat & Glo EM-415 - 36
Manual
Heat & Glo 350TRSILP-AUF
Manual
Heat & Glo Exclaim-50
Manual
Heat & Glo 6000 Series
Manual
Heat & Glo XLR-PLUS-N-AU
Manual
Heat & Glo 8000CFLP-OAKIPI
Manual
Heat & Glo BE-41C
Manual
Heat & Glo VRT-GY-P-AUB
Manual
Heat & Glo 6000CL-IPI-S
Manual
Heat & Glo ST-36TRLP-IPI
Manual
Heat & Glo SL-550TV-D
Manual
Heat & Glo 6000GL-IPILP-S
Manual
Heat & Glo BW36
Manual