Haier HDY-M40 - Manuals

Turning on power Before turning on the power of the dryer check whether the supply voltage is in accordance with the value indicated on the name plate. f Preparation of laundry load - The dryer can only dry laundry which has been spun dry. Do not put in laundry which is still dripping wet or has exc...

1. Power up Insert the power plug into an appropriate power outlet that is properly installed and grounded. Operating power supply: 220-240V~50Hz. 2. Laundry loading Open the door and load the laundry into the drum of the dryer. For a more energy efficient and better drying result, make sure the loa...

6 Dryer timer: The timer will let you set the time for up to 200 minutes to dry your clothes depending on the load of the clothes. This dryer has two program types. The light blue colour is the cool air cycle and the orange is the warm air cycle. During the cool air cycle the heater does not come on...

Cleaning the surface Wipe off any dust or dirt. Cleaning the filter screen To ensure good ventilation effect during drying, the filter screen must be cleaned before or after each use. 1. Remove the filter Gently push together the clip on the filter screen and then pull out towards yourself. 2. Clean...

Remove the transport packaging (fig.1) and remove the dryer rack from the top packaging (fig.2). Remove the tape on the front (fig.3 and fig.4), the wall mounting kit attached to the drum with tape on the inside and the panel film, before starting the dryer. Packing accessories Check list of the acc...

WALL MOUNTING INSTRUCTIONS 1. Determine the location of the dryer on the wall and mark the bracket position. A minimum 50 mm is needed between the top of the dryer and the celling for ease of installation; If mounting above a washing machine, allow sufficient room to open the lid of the washer. 9 To...

WALL MOUNTING INSTRUCTIONS 3. Install the hooks to the dryer, in the inverted position, remove the 2 screws and 2 plastic plugs as indicated in Fig.1 . 4. Align the hooks as shown in Fig.2 and refit screws tightly. Install the spacers provided as Fig.2. 10 plastic plugs 2 hooks 3 screws 2 spacers

WALL MOUNTING INSTRUCTIONS 5. With assistance, mount dryer on wall brackets. See Fig. 3 6. A second control panel with inverted symbols is supplied. Peel the release paper from the back of inverted film then place new control panel film on the surface so that the writing is the correct way around. 1...

DRYING RACK FITTING INSTRUCTION DRYER FREE STANDING-UPRIGHT For ease of access, the rack is to be mounted near the dryer top. Firstly hold the rack horizontally with the two end projections pointing upwards and away from yourself. Position the rack near the top of the dryer and place the end of the ...

14 The following must be confirmed before calling for service: Problem Possible Cause The dryer does not start The drying result is not good -Is the dryer plugged in? -Is the power on? -Is the door closed properly? -Has a drying program been set? -Was the correct drying program set? -Is the filter s...

Turning on power Before turning on the power of the dryer check whether the supply voltage is in accordance with the value indicated on the name plate. f Preparation of laundry load - The dryer can only dry laundry which has been spun dry. Do not put in laundry which is still dripping wet or has exc...

1. Power up Insert the power plug into an appropriate power outlet that is properly installed and grounded. Operating power supply: 220-240V~50Hz. 2. Laundry loading Open the door and load the laundry into the drum of the dryer. For a more energy efficient and better drying result, make sure the loa...

6 Dryer timer: The timer will let you set the time for up to 200 minutes to dry your clothes depending on the load of the clothes. This dryer has two program types. The light blue colour is the cool air cycle and the orange is the warm air cycle. During the cool air cycle the heater does not come on...

Cleaning the surface Wipe off any dust or dirt. Cleaning the filter screen To ensure good ventilation effect during drying, the filter screen must be cleaned before or after each use. 1. Remove the filter Gently push together the clip on the filter screen and then pull out towards yourself. 2. Clean...

Remove the transport packaging (fig.1) and remove the dryer rack from the top packaging (fig.2). Remove the tape on the front (fig.3 and fig.4), the wall mounting kit attached to the drum with tape on the inside and the panel film, before starting the dryer. Packing accessories Check list of the acc...

WALL MOUNTING INSTRUCTIONS 1. Determine the location of the dryer on the wall and mark the bracket position. A minimum 50 mm is needed between the top of the dryer and the celling for ease of installation; If mounting above a washing machine, allow sufficient room to open the lid of the washer. 9 To...

WALL MOUNTING INSTRUCTIONS 3. Install the hooks to the dryer, in the inverted position, remove the 2 screws and 2 plastic plugs as indicated in Fig.1 . 4. Align the hooks as shown in Fig.2 and refit screws tightly. Install the spacers provided as Fig.2. 10 plastic plugs 2 hooks 3 screws 2 spacers

WALL MOUNTING INSTRUCTIONS 5. With assistance, mount dryer on wall brackets. See Fig. 3 6. A second control panel with inverted symbols is supplied. Peel the release paper from the back of inverted film then place new control panel film on the surface so that the writing is the correct way around. 1...

DRYING RACK FITTING INSTRUCTION DRYER FREE STANDING-UPRIGHT For ease of access, the rack is to be mounted near the dryer top. Firstly hold the rack horizontally with the two end projections pointing upwards and away from yourself. Position the rack near the top of the dryer and place the end of the ...

14 The following must be confirmed before calling for service: Problem Possible Cause The dryer does not start The drying result is not good -Is the dryer plugged in? -Is the power on? -Is the door closed properly? -Has a drying program been set? -Was the correct drying program set? -Is the filter s...