Grizzly Industrial h8234 - Manuals

Page 3 - safety; NOTICE

Model H8234 28° Framing Nailer -1 - safety instructions for pneumatic tools 1. Keep all safety devices in place and in working order. 2. remove adJusting Keys and Wrenches. Form habit of check-ing to see that keys and adjusting wrenches are removed from tool before operation. 3. Keep WorK area clean...

Page 4 - safety instructions for pneumatic tools

Model H8234 28° Framing Nailer -2 - 10. use proper air hose for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretch-ing. 11. Wear proper apparel. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get ca...

Page 5 - additional safety instructions for nailers

Model H8234 28° Framing Nailer -3 - additional safety instructions for nailers 1. hand inJuries: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. combustible gases: Never con- nect the nailer t...

Page 7 - introduction; foreword

Model H8234 28° Framing Nailer -5 - introduction If you have any comments regarding this manual, please contact us: Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 email: [email protected] Most importantly, we stand behind our tools. If you have...

Page 8 - set up; inventory; unpacking

Model H8234 28° Framing Nailer -6 - set up inventory After you open the nailer box, you should find the following. model h8234 inventory (figure 1) Qty a. 28° Framing Nailer ............................. 1b. Safety Goggles ................................. 1c. Oil ......................................

Page 9 - compressed air

Model H8234 28° Framing Nailer -7 - The Model H8234 is designed to be oper-ated at 80-110 PSI using clean, dry, regu-lated, compressed air. do not exceed the 120 psi maximum operating pres-sure for your model. Before using your new nailer, regulate the air pressure to find the optimum setting within...

Page 11 - operations; loading

Model H8234 28° Framing Nailer -9 - operations loading When replacing nails in your model h8234, follow these guidelines: Nail Size ...................... 1 ⁄ 8 " Shank Diameter Nail Strip Angle ............... 28º Clipped HeadLength.............................................. 2"–3 1 ⁄ 2 &...

Page 12 - adjusting depth

Model H8234 28° Framing Nailer -10 - 5. Pull the trigger. — If the nail drove into the wood far enough, continue with your intended operations. — If the nail either went too far or not far enough, then go to the adjusting depth section on this page. 3. Depress the safety nose mechanism against your ...

Page 13 - clearing Jammed

Model H8234 28° Framing Nailer -11 - A jammed nail must be cleared before using the nailer again. to clear a jammed nail from the dis-charge area: 1. DISCONNeCT NAILeR FROM THe AIR SUPPLY! 2. Pull back and latch the magazine push- er. 3. Remove the nail stick from the maga- zine. 4. Locate the openi...

Page 14 - rings

Model H8234 28° Framing Nailer -12 - replacing pistons/o- rings Under heavy use, a piston, piston shaft, or O-ring may wear out. Replacement is quick and easy. Contact Grizzly Customer Service at (800) 523-4777 to obtain the Piston Repair Kit (Part Number PH8234092), or the complete O-Ring Repair Ki...

Page 15 - accessories

Model H8234 28° Framing Nailer -13 - accessories g2820 —pneumatic tool oil 8 oz.g2821—pneumatic tool oil 1 pintUse the right oil! This pneumatic tool oil offers outstanding heat displacement and friction reduction without eating away at delicate air components like detergent motor oils. Stock up wit...

Page 16 - cleaning & lubrication; cleaning

Model H8234 28° Framing Nailer -14 - cleaning & lubrication cleaning Use non-flammable solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this ...

Page 19 - troubleshooting; symptom

Model H8234 28° Framing Nailer -17 - troubleshooting symptom possible cause solution Air leaking at trig-ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking. 1. Loose screws in housing.2. Damaged O...

Page 20 - Warranty and returns

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-nance. This is Gri...