Grizzly Industrial H6144 - Manuals

Page 2 - SAFETY; Safety Instructions for Machinery; NOTICE

For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages...

Page 4 - Additional Safety Instructions for Nailers

H6144 34° Angle Finish Nailer–2½" -3 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combusti...

Page 6 - INTRODUCTION; Foreword

H6144 34° Angle Finish Nailer–2½" -5 - INTRODUCTION If you have any comments regarding this manual, please write to us at the following address: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have a...

Page 7 - SET UP; Unpacking; Inventory

H6144 34° Angle Finish Nailer–2½" -6 - SET UP Figure 1. Model H6144 inventory. B C D G Unpacking Your Model H6144 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for...

Page 9 - Safety Yoke

H6144 34° Angle Finish Nailer–2½" -8 - Safety Yoke A safety yoke mechanism on the nose of the nailer acts as a secondary safety device. When the trigger is pressed, the nailer will not fire until the safety yoke mechanism is depressed. Before you use your nailer for the first time, check the saf...

Page 10 - OPERATIONS; Loading; Operating

H6144 34° Angle Finish Nailer–2½" -9 - OPERATIONS Loading When replacing nails in your Model H6144, follow these guidelines: Gauge: 15Length: 1 1 ⁄ 4 " -2 1 ⁄ 2 " Capacity: 40Angle: 34° NOTICE: A number of manufacturers' nails may fit the Model H6144. However, for best performance, we re...

Page 11 - Adjusting Depth

H6144 34° Angle Finish Nailer–2½" -10 - Figure 5. Depth adjustment knob. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 5. Pull the trigger. If the nail drove into the wood far enough, continue with...

Page 12 - Clearing Jammed

H6144 34° Angle Finish Nailer–2½" -11 - The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis-charge area on the Model H6144: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Figure 7. Releasin...

Page 14 - CLEANING & LUBRICATION; Cleaning

H6144 34° Angle Finish Nailer–2½" -13 - CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this ...

Page 17 - TROUBLESHOOTING; PROBLEM

H6144 34° Angle Finish Nailer–2½" -16 - 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws.2. Replace O-ring.3. Tighten air fitting & use teflon tape. 1. Replace damaged seals. 1. Tighten screws and fit- tings. 2. Clean nose.3. Clean magazine and in...

Page 18 - WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Griz...

Page 19 - WARRANTY CARD

Name _________________________________________________________________________Street ________________________________________________________________________City____________________State________Zip_________Phone Number____________E-Mail___________________FAX ____________Model # H6144 34°Angle Finish...

Page 20 - Send a Grizzly Catalog to a friend:; Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here