Grizzly Industrial G9984 - Manuals

G9984/G9985 (Mfd. Since 07/18) -7- SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G9984/G9985 Oscillating Belt Edge Sander . The Model G9984/G9985 is part of a growing Grizzly fam-ily of fine woodworking machinery. When used according to the guidelines set forth in this manu-al, you...

-8- G9984/G9985 (Mfd. Since 07/18) Unpacking The Model G9984/G9985 is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you have signed for delivery, immediately call Customer Service for advice. The Model G9984/G9985 has two lifting rings locat...

G9984/G9985 (Mfd. Since 07/18) -9- Piece Inventory After all the parts have been removed from the carton, you should have: • (2) Base Support • (2) Star Knob M10-1.5 x 15 • (4) Lock Washer 10mm • (4) Flat Washer 10mm • (4) Hex Bolt M10-1.5 x 30 • (4) Rubber Foot 1 ⁄ 2 "-12 x 1 • (1) Sanding Belt...

-10- G9984/G9985 (Mfd. Since 07/18) Hardware Recognition Chart 5mm 10mm15mm20mm25mm30mm35mm40mm45mm50mm55mm60mm65mm70mm75mm Washer Lock Washer Hex Nut Wing Nut Phillips HeadSheetMetalScrew Setscrew Phillips Head Screw ThumbScrew Slotted Screw CountersunkPhillipsHead Screw Cap Screw Carriage Bolt Hex...

G9984/G9985 (Mfd. Since 07/18) -11- Clean Up The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship-ment. Remove this protective coating with a sol-vent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. Avoid chlorine-based solvents as they ma...

G9984/G9985 (Mfd. Since 07/18) -13- Attaching the base supports to the main base: 1. Slide the base supports under the main machine base. 2. Using (4) M10-1.5 x 30 hex bolts, (4) 10mm flat washers, and (4) 10mm lock washers, secure the main machine base to the base supports as shown in Figure 7. Be ...

-14- G9984/G9985 (Mfd. Since 07/18) SECTION 5: ADJUSTMENTS Disconnect power to the machine when perform- ing any adjustments on the Model G9984/G9985. Failure to do this may result in serious person- al injury. Wear safety glasses during the entire adjust- ment process. Failure to comply may result ...

-16- G9984/G9985 (Mfd. Since 07/18) The main table is adjustable to accommodate a wide range of workpieces and sanding operations. Because the main table is designed with a special balance mount, it is easily adjusted up and down. To adjust the main table: 1. Loosen the lock handles on the front of ...

-18- G9984/G9985 (Mfd. Since 07/18) The side table can be adjusted to accommodate sanding at various angles. To adjust the angle position of the side table: 1. Loosen the lock handle underneath the side table shown in Figure 19. 2. Move the side table to the desired position. 3. While holding the si...

G9984/G9985 (Mfd. Since 07/18) -19- SECTION 6: OPERATIONS Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your fin-ger is poised on the switch, just in c...

-20- G9984/G9985 (Mfd. Since 07/18) SECTION 7: MAINTENANCE Lubrication There are (2) grease fittings shown in Figure 20. Grease these points after approximately 50 hours of use. All other bearings are sealed and permanently lubricated, simply leave them alone until they need to be replaced. Do not l...

-22- G9984/G9985 (Mfd. Since 07/18) SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before ...

G9984/G9985 (Mfd. Since 07/18) -23- G9984 Revised Wiring Diagram 2T1 6T3 14NO 4T2 1L1 5L3 13NO 3L2 NHD 220V T1 T2 T3 98 17 18 A2 A1 95 97 ON 96 Ground Ground 1-PHASE 220 VAC 3 HP MOTOR MAGNETIC CONTACTOR SWITCH Start Capacitor 300MFD 250VAC Run Capacitor 20MFD 500VAC Hot Hot Ground 6-20 Plug (As Rec...

-24- G9984/G9985 (Mfd. Since 07/18) G9985 Revised Wiring Diagram 2T1 6T3 14NO 4T2 1L1 5L3 13NO 3L2 NHD 220V T1 T2 T3 98 17 18 A2 A1 95 97 ON 96 Ground Ground 3-PHASE 220 VAC 3 HP MOTOR MAGNETIC CONTACTOR SWITCH Ground Hot Hot Hot 15-15 PLUG (as recommended) W Z G X W1 V1 U1

G9984/G9985 (Mfd. Since 07/18) -25- Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type ..................................................................................................... Floor Model Overall Dimensions and Speci...

-26- G9984/G9985 (Mfd. Since 07/18) Design Type ..................................................................................................... Floor Model Overall Dimensions and Specifications: Table Size ...........................................................................................

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

G9984/G9985 Oscillating Belt Edge Sander -5- SECTION 2: CIRCUIT REQUIREMENTS 220V Single-Phase 220V Three-Phase G9984 Only: The Model G9984 has a 3 H.P., 1725 R.P.M.motor which requires a 220V single-phase circuit.The cord set included does not have a plug, asthe style of plug you require will depen...

-6- G9984/G9985 Oscillating Belt Edge Sander We do not recommend the use of extension cordswith 220V equipment. It is much better to arrangethe placement of your equipment and the installedwiring to eliminate the need for extension cords.Should it be necessary to use an extension, makesure the cord ...

G9984/G9985 Oscillating Belt Edge Sander -7- SECTION 3: INTRODUCTION We are proud to offer the Grizzly ModelG9984/G9985 Oscillating Belt Edge Sander . TheModel G9984/G9985 is part of a growing Grizzlyfamily of fine woodworking machinery. Whenused according to the guidelines set forth in thismanual, ...

-8- G9984/G9985 Oscillating Belt Edge Sander Unpacking The Model G9984/G9985 is shipped from themanufacturer in a carefully packed carton. If youdiscover the machine is damaged after you havesigned for delivery, immediately call CustomerService for advice. The Model G9984/G9985 has two lifting rings...

G9984/G9985 Oscillating Belt Edge Sander -9- Piece Inventory After all the parts have been removed from the carton, you should have: • (2) Base Support• (2) Star Knob M10-1.5 x 15• (4) Lock Washer 10mm• (6) Flat Washer 10mm• (4) Hex Bolt M10-1.5 x 30• (4) Rubber Foot 1 ⁄ 2 "-12 x 1 • (1) Sanding...

-10- G9984/G9985 Oscillating Belt Edge Sander Hardware Recognition Chart 5mm 10mm15mm20mm25mm30mm35mm40mm45mm50mm55mm60mm65mm70mm75mm Washer Lock Washer Hex Nut Wing Nut Phillips HeadSheetMetalScrew Setscrew Phillips Head Screw ThumbScrew Slotted Screw CountersunkPhillipsHead Screw Cap Screw Carriag...

G9984/G9985 Oscillating Belt Edge Sander -11- Clean Up The unpainted surfaces are coated with a waxy oilto protect them from corrosion during shipment.Remove this protective coating with a solventcleaner or citrus-based degreaser such asGrizzly’s G7895 Degreaser. Avoid chlorine-basedsolvents as they...

-12- G9984/G9985 Oscillating Belt Edge Sander SECTION 4: ASSEMBLY Most of your Model G9984/G9985 has beenassembled at the factory, but some parts must beassembled or installed after delivery. TOOLS REQUIRED: You will need a small adjustable wrench, a flat and Phillips head screw-driver, and a machin...

G9984/G9985 Oscillating Belt Edge Sander -13- Attaching the base supports to the main base: 1. Slide the base supports under the mainmachine base. 2. Using (4) M10-1.5 x 30 hex bolts, (4) 10mmflat washers, and (4) 10mm lock washers,secure the main machine base to the basesupports as shown in Figure ...

-14- G9984/G9985 Oscillating Belt Edge Sander SECTION 5: ADJUSTMENTS Disconnect power to themachine when perform-ing any adjustments onthe Model G9984/G9985.Failure to do this mayresult in serious person-al injury. Wear safety glassesduring the entire adjust-ment process. Failure tocomply may result...

-16- G9984/G9985 Oscillating Belt Edge Sander The main table is adjustable to accommodate awide range of workpieces and sanding operations.Because the main table is designed with a specialbalance mount, it is easily adjusted up and down.To adjust the main table: 1. Loosen the lock handles on the fro...

G9984/G9985 Oscillating Belt Edge Sander -17- The main table has a stationary miter gauge thatis used to hold the workpiece at various anglesagainst the sanding belt. To adjust the mitergauge: 1. Loosen the lock handle shown in Figure 16 . 2. Rotate the miter gauge to the desired angle. 3. While hol...

G9984/G9985 Oscillating Belt Edge Sander -19- SECTION 6: OPERATIONS Once assembly is complete and adjustments aredone to your satisfaction, you are ready to test runthe machine. Turn on the power supply at the main panel.Press the START button. Make sure that your fin-ger is poised on the switch, ju...

-20- G9984/G9985 Oscillating Belt Edge Sander SECTION 7: MAINTENANCE Lubrication There are (2) grease fittings shown in Figure 20 . Grease these points after approximately 50 hoursof use. All other bearings are sealed and permanentlylubricated, simply leave them alone until theyneed to be replaced. ...

-24- G9984/G9985 Oscillating Belt Edge Sander Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type ...................................................................................................... Floor Model Overall Dimension...

G9984/G9985 Oscillating Belt Edge Sander -25- Design Type ...................................................................................................... Floor Model Overall Dimensions and Specifications: Table Size.................................................................................

-36- G9984/G9985 Oscillating Belt Edge Sander NOTES

-38- G9984/G9985 Oscillating Belt Edge Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alt...

10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt S...