Grindmaster 3511 - Manuals - manualsarea.com

Page 3 - Table of Contents

Table of Contents Safety Precautions .................................................................................................... 2 Freezer Applications & Specifications ..................................................................... 2 - 3 Installation ................................

Page 4 - OPERATOR’S SAFETY PRECAUTIONS; operate this machine.; FREEZER APPLICATION AND SPECIFICATIONS; Product Tips

OPERATOR’S SAFETY PRECAUTIONS IMPORTANT: Failure to comply with the following safety precautions may result in severe personal injury or damage to the machine.1. Read and understand the operating instructions in this manual thoroughly. Only allow properly trained persons to operate this machine. 2. ...

Page 5 - Carburetor Assembly; Most applications only require the standard carb tube.; Mix Considerations - General; Thick product carb tube

Product Tips (cont.) Some cappuccino or latté mixes contain dairy products which can spoil if not refrigerated. If the freezer is to be turnedoff at night these products must be removed from the freezer. Contact your local health department regarding its regulations for proper mix handling and stora...

Page 6 - INSTALLATION; until the freezer has been checked for

Page 4 Model 3511 INSTALLATION Shipment Transit 1. The freezer has been operated and tested at the factory. Upon arrival the complete freezer must be thoroughly checked for any damage which may have occurred in transit. Note: A Tip (N) Tell warning device is placed on each shipping carton at the fac...

Page 8 - OPERATION AND ADJUSTMENTS

Accessory Installation The Model 3511 has several optional accessories that can be addedto the unit in the field to meet your application’s needs. Theseaccessories come with installation instructions.• Spinner - Spinners are typically used in applications that add flavoring to a frozen neutral base ...

Page 9 - Increase Thickness; Figure L

Consistency Adjustment From time to time, it may become necessary to readjust the consistency setting (thickness) to compensate for variation between different mixes or to switch from one type of product to another. This adjustment is made as follows: 1. Disconnect electrical power. WARNING: Do not ...

Page 10 - CARE AND CLEANING

CARE AND CLEANING Cleaning and sanitizing frequency must be followed according to state and local health department regulations. NOTE: Each time the freezer is fully disassembled, all foodzone freezer components must be thoroughly washed and sanitized using procedures recommended by the local health...

Page 13 - solution taking care to remove any remaining lubricant.; MAINTENANCE; Suggested Daily Maintenance

Clean-In-Place Procedure (Daily Cleaning) This equipment has been approved for a Clean-In-Place procedure that does not require complete disassembly on adaily basis. The unit still requires regular complete disassembly for cleaning and sanitizing. To perform the C-I-Pprocedure follow the instruction...

Page 14 - Preventative Maintenance Procedure (Every 6 to 12 Months)

Page 12 Model 3511 Preventative Maintenance Procedure (Every 6 to 12 Months) A preventative maintenance visit should be performed every 6 to 12 months depending on the usage and environ-ment where the unit is placed. (Ex. seasonal machines - once before season, year round machines - twice per year)....

Page 15 - Use compressed air or CO; How to Adjust Belt; the bearing collar to the motor shaft.; How to Change Back Lit Sign Merchandiser Bulb

How to Clean Condenser (Air-Cooled Unit Only)NOTE: Loss of refrigeration efficiency will result if condenser is allowed to become dirty. Excessive compressor run time or loss of capacity are a good indication that the condenser needs to be cleaned.1. Disconnect electrical power. 2. Remove side panel...

Page 16 - GENERAL TROUBLESHOOTING; PROBLEM

Page 14 Model 3511 GENERAL TROUBLESHOOTING Freezer problems originate from three sources - improper operation, mix problems or mechanical malfunction. Always check for improper operation and mix problems first, as they are the most common cause of most equipmentproblems. CAUTION: Always disconnect p...

Page 17 - CHECK LIST; ARTS IDENTIFICA

1 2 Rough Side of Ceramic Smooth Shiney Side CHECK LIST P ARTS IDENTIFICA TION Coconut Oil Seal (W0340210) and S tandard Seal (W0340201) include 1,2, & 3 . Slush Plunger (W0480438) Thick Product Plunger (W0480451) (W0430026) Scraper Blade Dasher (W0430089) (W0631230) Use with scraper blade dashe...

Page 19 - Drive Motor Assembly (See figure on left)

Model 3511 Page 17 Model 3511Base Assembly ITEM PARTNUMBER DESCRIPTION ITEM PARTNUMBER DESCRIPTION 1 W0210169 Motor Cradle 7 W0610559 Bolt for Bearing 2 W0320020 Motor, Drive Dual Cycle1/2HP 8 W0611249 Washer, Split, Lock, Z/P 3 W0321013 Nut, Motor Adjustment 9 W0671022 Insulation, Motor BrktSound 4...