Graco 243080 - Manuals

Component Identification 8 334567P Component Identification Stand Models A ON/OFF Switch B Pressure Control D Prime ValveF Tip Guard G Spray TipH GunJ Airless Hose K Power Cord L Trigger Lock M Drain TubeN Fluid IntakeP Pump R Fluid OutletS Power Cord Wrap U FilterV Finger Guard / TSL Fill PointMode...

Grounding 334567P 11 Grounding This sprayer is equipped with a Power Cord that has a ground wire and an appropriate grounding plug.The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.Do not modify the plug provided; if it ...

Pressure Relief Procedure 334567P 13 6. Put drain tube in a pail. Turn prime valve down. Leave prime valve in down (drain) position until you are ready to spray again. 7. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved: a. VERY SLOWLY loosen the tip guard...

Setup 14 334567P Setup When unpacking sprayer for the first time or after long term storage perform setup procedure. When first setup is performed remove shipping plug from fluid outlet.1. Connect Graco airless hose to fluid outlet. Use wrenches to tighten securely. 2. Connect other end of hose to g...

Startup 334567P 17 Startup 1. Perform Pressure Relief Procedure , page 12. 2. Turn pressure control to lowest pressure. 3. Turn ON/OFF switch to ON position. 4. Place fluid intake in paint pail. Place drain tube in waste pail. 5. Increase pressure 1/2 turn to start motor. Allow paint to circulate th...

Operation 334567P 19 Operation Spray Tip Installation 1. Perform Pressure Relief Procedure , page 12. 2. Use spray tip (A) to insert OneSeal ™ (B) into tip guard (C). 2. Insert Spray Tip. 3. Screw assembly onto gun. Tighten. Spray When a RAC X™ FF LP Fine Finish Low Pressure reversible spray tip is ...

Operation 20 334567P 1. Spray test pattern. Adjust pressure to eliminate heavy edges. 2. Use smaller tip size if pressure adjustment cannot eliminate heavy edges. 3. Hold gun perpendicular, 10-12 in. (25-30 cm) from surface. Spray back and forth; overlap by 50%. 4. Trigger gun after moving. Release ...

Operation 334567P 21 Cleanup 1. Perform Pressure Relief Procedure , page 12. 2. Remove tip guard and Spray Tip. For additional information, see separate gun manual. 3. Remove fluid intake and drain tube from paint, wipe excess paint off outside. 4. Place fluid intake in flushing fluid. Use water for...

Maintenance 24 334567P Maintenance Routine maintenance is important to ensure proper operation of your sprayer. Maintenance includes performing routine actions which keep your sprayer in operation and prevents trouble in the future. Activity Interval Inspect/clean sprayer filter, fluid inlet straine...

Troubleshooting 334567P 25 Troubleshooting Mechanical/Fluid Flow 1. Follow Pressure Relief Procedure , page 12, before checking or repairing. 2. Check all possible problems and causes before disassembling the unit. Problem What to Check If check is OK, go to next check What to Do When check is not O...

Troubleshooting 28 334567P Electrical Symptom: Sprayer does not run, stops running, or will not shut off. Perform Pressure Relief Procedure , page 12.1. Plug sprayer into correct voltage, grounded outlet. 2. Turn the ON/OFF switch OFF, wait 30 seconds and then turn power back ON again (this ensures ...

Sprayers Parts 32 334567P Sprayers Parts 59 67 54 36 47 47 23 12 56 71 95 63 53 68 65 ti24099a 7 54b 54c 54d 54a 1 1 See page 42. 2 Ref. Torque 140-160 in-lb (15.8 - 18.1 N•m) 30-35 in-lb (3.4 - 4.0 N•m) 23-27 in-lb (2.6 - 3.1 N•m) 1 2 4 4

Sprayers Parts 34 334567P 190, 290, 390 Stand Sprayers Parts List Ref. Part Description Qty. 1 107434 BEARING, thrust 1 7 115498 SCREW, mch, slot/hex, wash hd 1 8 116073 WASHER, thrust 1 9 116074 WASHER, thrust 1 10 116079 BEARING, thrust 2 12 117501 SCREW, mach, slot hex wash hd 4 14 117559 O-RING ...

390 Lo-Boy Sprayer Parts 334567P 35 390 Lo-Boy Sprayer Parts 53 12 65 63 54 82 83 59 47 69 46 68 66 74 150 56 ti24101a 36 7 54b 54c 54d 54a 1 4 See page 42. 2 2 Ref. Torque 140-160 in-lb (15.8 - 18.1 N•m) 30-35 in-lb (3.4 - 4.0 N•m) 23-27 in-lb (2.6 - 3.1 N•m) 1 2 4

Accessories and Labels 334567P 41 Accessories and Labels Sprayer Model (Series) Ref. 27 Hose, 1/4 in. x   ft Ref. 28 Gun, Spray Ref. 52 Label, Front Ref. 53 Label, Side Ref. 65 Label, Warning  Ref. 34 Card, Medical Alert  Ref. 63 Label, Danger  17C310 17C313 240794  288430 17E998 17E999 195793...

Control Box and Filter 42 334567P Control Box and Filter 146 150 15 24 24 36 35 27 17 18 16 2 49 56 12 97 21 38 51 4 5 26 ti25121a 49a 133 56 90 91 2 1 8 7 1 Ref. Torque 140-160 in-lb (15.8 - 18.1 N•m) 30-35 in-lb (3.4 - 4.0 N•m) 130-150 in-lb (14.7 - 16.9 N•m) 48-72 in-lb (5.4 - 8.1 N•m) 1 2 7 8

Control Box and Filter 334567P 43 Control and Filter Parts List Ref. Part Description Qty. 2 117828 PACKING, o-ring 1 4 111600 PIN, grooved 1 5 277364 GASKET, seat, valve 1 12 117501 SCREW, mach, hex washer hd 3 15 See page 44 MANIFOLD, fluid 1 16* FILTER, fluid 1 Tall manifold 246425 30 mesh (gray)...

Wiring Diagrams 334567P 45 Wiring Diagrams 110/120V Red (+) Black (-) PressureControlAssembly PowerPlug White Green Black from Motor 2 x Yellow ON/OFFSwitch ti5643a Capacitor Replaceable Fuse ti5643a

Technical Specifications 48 334567P Technical Specifications 190/290/390 US Metric SprayerMaximum fluid working pressure 190 3000 psi 207 bar, 20.7 MPa 290/390 3300 psi 228 bar, 22.8 MPa Maximum Delivery 190 PC Classic, 190 PC Express 0.38 gpm 1.4 lpm 290/390 PC Classic, 390 PC, NOVA 390 PC, 190 PC ...

California Proposition 65 334567P 49 California Proposition 65 Noise** (dBa) @ 70 psi (0.48 MPa, 4.8 bar) Sound pressure 90 dBa Sound power 100 dBa Materials of ConstructionWetted materials on all models zinc- and nickel-plated carbon steel, nylon, stainless steel, PTFE, Acetal, leather, UHMWPE, alu...

Graco Standard Warranty 50 334567P Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any...

Graco Information 334567P 51 Graco Information For the latest information about Graco products, visit www.graco.com . For patent information, see www.graco.com/patents . TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

10 824192 Parts Drawing – Pressure Control 22 52 29 21 18 25 24 51 28 34 23 30 33 27 32 39 36 35 26 Ref 1 Ref 45 37 22 9537A NOVA / NOVApro / SuperNOVApro

11 824192 Parts List – Pressure Control NOVA / NOVApro / SuperNOVApro REF NO. PART NO. DESCRIPTION QTY REF NO. PART NO. DESCRIPTION QTY 18 115492 SCREW, slot hd., hex, washer hd 6 21 276539 HOUSING, control 1 22 115495 SCREW, slot hd, hex, washer hd 5 23 195429 SWITCH, toggle 1 24 105658 RING, locki...

12 824192 Phone Number TO PLACE AN ORDER OR FOR SERVICE , contact your Graco distributor, or call this number to identify the distributor near you: 1–800–690–2894 Toll Free All written and visual data contained in this document reflect the latest product information available at the time of publicat...