Graco 17D889 - Manuals

Component Identification 333394H 7 Component Identification A B C D E F G H N L K S R Spray J M ti25736a P Prime Pump A Cup Cover B FlexLiner C Cup Support D VacuValve Cap E VacuValve Air Hole F VacuValve Reservoir G Strainer H Spray Tip Holder J Prime Pump/Spray Knob K Power Cord L Sprayer Trigger ...

Start Up 8 333394H Start Up Starting a New Job If you are using the sprayer for the very first time, see Flushing a New Sprayer , page 20. 1. Install FlexLiner in the cup support. 2. Fill FlexLiner with material. Securely tighten cup cover onto cup support. Tighten so the arrow on the cup cover is w...

Start Up 333394H 9 5. Tilt the sprayer so the VacuValve is the highest point, causing any air in the FlexLiner to rise to the VacuValve. Gently squeeze the FlexLiner to evacuate all air through the VacuValve air hole. Once you see material enter the VacuValve reservoir, all air should be evacuated f...

Start Up 10 333394H If sprayer does not spray, try one of the steps below: • Make certain there is only one FlexLiner in cup support. It is possible for two liners to nest tightly together and appear as only one. • Make certain the cup cover is properly threaded to the cup support. If threads are vi...

How to Spray 333394H 11 How to Spray Take a few moments prior to spraying and review these simple tips to ensure your spraying project is a success. Dual Speed Control (Not available on all units) The dual speed control feature allows you to slow down or speed up when spraying. • Turn the dual speed...

How to Spray 12 333394H Triggering Sprayer Pull trigger after starting stroke. Release trigger before end of stroke. Sprayer must be moving when trigger is pulled and released. Aiming Sprayer Aim sprayer at bottom edge of previous stroke, overlapping each stroke by half. Rotating the spray tip guard...

How to Spray 333394H 13 Spray Pattern Quality A good spray pattern is evenly distributed as it hits the surface. If tails persist, material may need to be thinned. If material needs to be thinned follow manufacturers recommendations. If you see pulsations in the pattern, try the following: • On the ...

Cleanup 14 333394H Cleanup Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. 1. Disconnect power (unplug power cord). 2. Turn Prime Pump/Spray Knob down to PRIME PUMP position to relieve pressure. Cleaning Sprayer Cleaning your sprayer properly and after ev...

Cleanup 16 333394H 13. Remove cup assembly and discard used fluid. Dispose of used cleaning fluid properly. 14. Replace cleaning fluid and repeat steps 1- 13 until spray output is clean. IMPORTANT! For best results, do not spray more than one cup of water through the tip while cleaning. If more flus...

Storage 333394H 17 Storage Pump Armor fluid protects the sprayer while in storage. It helps protect sprayer against freezing and corrosion when not in use.1. Clean the sprayer and cup assembly. See Cleanup , page 14 . 2. Turn Prime Pump/Spray knob down to the Prime Pump position. Remove cup support ...

Common Procedures 18 333394H Common Procedures Installing Spray Tips Two spray tips are available for use with this sprayer. The black tip produces a 12-inch wide spray pattern. The gray tip produces a 4-inch wide spray pattern. Either spray tip may be used to spray mate- rials that are recommended ...

Common Procedures 333394H 19 Unclogging Spray Tip In the event that particles or debris clog the spray tip, this sprayer is designed with a reversible spray tip that quickly and easily clears the particles without disassembling the sprayer. 1. Perform Pressure Relief Procedure , page 14 . 2. To uncl...

Replacement Parts 22 333394H Replacement Parts Models 16Y385, 16Y386, 17A466 8 19 19 20 24 13a 13b 12 7 8 5 1 10 2 6 3 4 9 18 17 16 14 15 22 ti23460a ti23568a 26

Troubleshooting 26 333394H Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to an authorized service center. Sprayer Diagnostics ti24021a Have a Question? Call toll-free: 1-888-541-9788 Or visit us at: www.paintsprayersbygraco.com Problem Cause Solution Spr...

Technical Data 30 333394H Technical Data Hand-Held Sprayer U.S. Metric Max Working Pressure TrueCoat 360 1200 psi 8.3 MPa, 83 bar TrueCoat 360 DS/DSP/VSP 1300 psi 9 MPa, 90 bar Maximum Amperage 2.5 Amps 2.5 Amps Weight TrueCoat 360, 360 DS/DSP 3.5 lb (18 in.cord) 1.6 kg (45 cm cord) TrueCoat 360 VSP...

Graco Limited Warranty 333394H 31 Graco Limited Warranty Graco warrants to the original purchaser that this product will be free from defects in material and workmanship for one (1) year from the date of purchase when operated and maintained in accordance with Graco's written recommendations and ins...

6 Revolutionize your workday with the Graco Pro Series sprayers. They’re equipped with the breakthrough technology of the ProXChange Pump which allows you to replace your pump on the job faster and easier without any tools, eliminating downtime and keeping you spraying. Get your midsize-to-large job...

7 Full-time painting pros depend on sprayers that stay up and running, day in and day out, while delivering versatility and high-quality application. Graco’s Commercial Series sprayers handle the widest range of interior and exterior jobs. They’re loaded with smart, rugged design features that make ...

8 SG2 ™ Metal Spray Gun – 243011 • In-handle paint filter reduces tip clogs and improves finish • Full trigger (4-finger) is comfortable when spraying for long periods of time • Trigger pull is 30% lighter than competitors for easy operation and less fatigue • Includes 515 Reverse-A-Clean RAC ® IV S...

MAXIMUM TIP SIZE GRACO SPRAYERS MAXIMUM TIP SIZE SUPPORTED Project Painter Plus .015 in Magnum X5 .015 in Magnum X7 .017 in Magnum ProX17 .017 in Magnum ProX19 .019 in Magnum ProX21 .021 in TrueCoat Pro II .017 in Graco Pro210 es .021 in The last two digits are the size of the tip opening in thousan...

GRACO PRODUCT COMPARISON TrueCoat 360 TrueCoat 360 DSP TrueCoat 360 VsP TrueCoat Pro II Magnum Project Painter Plus Magnum X5 Magnum X7 Magnum ProX17 Magnum ProX17 Magnum ProX19 Magnum ProX19 Magnum ProX21 Magnum ProX21 Pro210 es Model Number 16Y385 16Y385 17D889 16N673 257025 262800 262805 17G177 1...

© 2016 Graco Inc. 344066A 10/16 Printed in the U.S.A.Refer to the operating manual for complete details on limited 1 year warranty. Questions? 888- 541-9788 magnum.graco.com/aplus magnum.graco.com Brand Preferred by PROS! MADE IN THE USA WITH GLOBAL COMPONENTS AGAINST MANUFACTURING DEFECTS L I M I T...