Fujitsu TE988G - Manuals - manualsarea.com

Page 2 - Fujitsu TE988G Color Monitor; FCC Information; Notice; Energy Declaration

Fujitsu TE988G Color Monitor 1 FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in ...

Page 3 - Important Safeguards

Fujitsu TE988G Color Monitor 2 Important Safeguards 1. Follow all warnings and instructions marked on the video monitor. 2. Do not use attachments which is not recommended by the video monitor manufacturer as they may cause hazards. 3. Do not expose the monitor to rain, water, moisture or direct sun...

Page 5 - Installation; Figure 1

Fujitsu TE988G Color Monitor 4 Installation Tilt Swivel & Base 1. Turn the monitor upside down. 2. Turn the base upside down. Insert its four hooks into the four slots on the bottom of the monitor. (Point the hooks on the base toward the front of the monitor) Figure 1 3. Push the tilt swivel and...

Page 6 - Monitor Connection; Figure 3 :Connecting the monitor; Pin Assignment; Pin

Fujitsu TE988G Color Monitor 5 Monitor Connection To attach the monitor to your system, follow the steps as described below: 1. Turn off the monitor and computer. 2. Connect one end of the power cable to your monitor and the other end to the power outlet. 3. Connect the 15-pin D-Sub signal cable to ...

Page 7 - Operation and User Adjustment; Control Panel

Fujitsu TE988G Color Monitor 6 Operation and User Adjustment Control Panel Figure 4 shows the position of following operating units: 1. Power ON / OFF Switch 2. Power LED 3. Menu – Displays OSD menu & Scrolls through OSD menu 4. Function Control Key – Adjust level of selected items

Page 8 - On-Screen Display Guide; Contrast & Brightness; Figure5 Contrast Adjustment Parameter; in figure 7

Fujitsu TE988G Color Monitor 7 On-Screen Display Guide 1. Contrast & Brightness (1).Press either 5 or 6 6 6 6 to activate and make the contrast adjustment shown by the OSD parameter. The parameter moves rightward indicating contrast increase and leftward indicating contrast decrease. 63 Figure5 ...

Page 12 - RGB Value Setting; OSD Position

Fujitsu TE988G Color Monitor 11 ( 6 ). RGB Color Temperature function window. R-Gain 9300¢ X K/User 30 63 12 /7500¢ X K RGB Value Setting The current setting of the color temperature is presented in purple. Press 5 or 6 key to scroll the black bar up or down to your desired item. There are three fac...

Page 13 - Recall

Fujitsu TE988G Color Monitor 12 ( 8 ). Language function window Press u or t to select your desired language, and then the OSD menu will be presented in the language selected. Note : No message will be displayed if you select “None”. ( 9 ). Tools function window. Recall None . 1. Recall factory sett...

Page 14 - Note; matter auto or manual degaussing was performed last time.; Leave The OSD

Fujitsu TE988G Color Monitor 13 Note 1. Degauss • User need to perform manual degaussing , once display monitor is turned to other direction. • It's recommended to wait 15 minutes before user to make next degaussing activity , no matter auto or manual degaussing was performed last time. 2. The icon,...

Page 15 - Specifications

Fujitsu TE988G Color Monitor 14 Specifications CRT SIZE 19 " diagonal, 90 0 deflection Viewable area 18 " Dot pitch 0.26mm Video: Analog (0.7Vp-p/1.0 Vp-p, 75 ohm positive) Selected by OSD Control Input Signal Sync : Separate sync, positive or negative TTL Input Connector 15-pin D-connector ...

Page 16 - Trouble Shooting; Problem

Fujitsu TE988G Color Monitor 15 Trouble Shooting If you are experiencing difficulties with your monitor, check following table for possible solutions. Problem Items to check ? No picture 1. The VGA card should be completely seated in the slot. 2. Power switch of the monitor and the PC should be in t...