Fujitsu T1000 - Manuals

ix Figures FIGURE 1-1 Server 2 FIGURE 1-2 Slide Rail Assembly 5 FIGURE 1-3 Mounting Bracket Locks 6 FIGURE 1-4 Cable Management Bracket 7 FIGURE 1-5 Locations of Ports and Connectors on the Rear Panel 8 FIGURE 2-1 Unlocking the Slide Rail Assembly 12 FIGURE 2-2 Mounting Bracket Release Button 13 FIG...

xi Tables TABLE 1-1 Ethernet Connection Transfer Rates 9 TABLE 3-1 Server Device List 38

xiii Code Samples CODE EXAMPLE 3-1 Boot Sequence Example 28 CODE EXAMPLE 3-2 Example of Normal System Initialization Output 37 CODE EXAMPLE 3-3 Example of Server Boot from Disk 0 39 CODE EXAMPLE A-1 Typical Boot Sequence Following Firmware Update 45

xv Preface This guide provides instructions, background information, and reference material tohelp you install the SPARC Enterprise T1000 Server. Instructions for installation in the document assume that a system administrator isexperienced with the Solaris ™ Operating System (Solaris OS). Note – Al...

xvi SPARC Enterprise T1000 Server Installation Guide • April 2007 Structure and Contents of This Manual This manual is organized as described below: ■ CHAPTER 1 Preparing for Installation Provides an overview of the SPARC Enterprise T1000 Server installationprocess. ■ CHAPTER 2 Installing the Server...

xviii SPARC Enterprise T1000 Server Installation Guide • April 2007 Using UNIX Commands This document might not contain information about basic UNIX® commands andprocedures such as shutting down the system, booting the system, and configuringdevices. Refer to the following for this information: ■ So...

Preface xix Prompt Notations The following prompt notations are used in this manual. Conventions for Alert Messages This manual uses the following conventions to show alert messages, which areintended to prevent injury to the user or bystanders as well as property damage, andimportant messages that ...

xx SPARC Enterprise T1000 Server Installation Guide • April 2007 Alert messages in the text An alert message in the text consists of a signal indicating an alert level followed byan alert statement. Alert messages are indented to distinguish them from regulartext. Also, a space of one line precedes ...

Preface xxi Product Handling Maintenance Warning – Certain tasks in this manual should only be performed by a certified service engineer. User must not perform these tasks. Incorrect operation of thesetasks may cause electric shock, injury, or fire. ■ Installation and reinstallation of all component...

xxii SPARC Enterprise T1000 Server Installation Guide • April 2007 Alert Labels The followings are labels attached to this product: ■ Never peel off the labels. ■ The following labels provide information to the users of this product. Sample of SPARC Enterprise T1000

xxiv SPARC Enterprise T1000 Server Installation Guide • April 2007 FOLD AND TAPE FOLD AND TAPE BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO 741 SUNNYVALE CA NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES POSTAGE WILL BE PAID BY ADDRESSEE FUJITSU COMPUTER SYSTEMSAT TENTION ENGINEERING OPS M/S ...

1 C H A P T E R 1 Preparing for Installation This chapter describes the server installation, and provides background informationabout the installation procedures that begin in Chapter 2 . This chapter contains these topics: ■ “Tools Needed” on page 2 ■ “Optional Components” on page 3 ■ “Installation...

2 SPARC Enterprise T1000 Server Installation Guide • April 2007 Server Overview FIGURE 1-1 shows the server. FIGURE 1-1 Server Tools Needed ■ No. 2 Phillips screwdriver ■ ESD mat and grounding strap

Chapter 1 Preparing for Installation 3 Optional Components The standard components of the server are installed at the factory. However, if youordered options such as additional memory or a PCI card, these may be shippedseparately. Install these components prior to installing the server in a rack. If...

4 SPARC Enterprise T1000 Server Installation Guide • April 2007 4. Mount the server into a rack or equipment cabinet. See “To Install the Server in the Rack” on page 19 . Note – In the rest of this document, the term rack means either an open rack or a closed cabinet. 5. Connect the server to a seri...

Chapter 1 Preparing for Installation 5 The Solaris OS is preinstalled on the server. When you power on, you areautomatically guided through the Solaris OS configuration procedure. See “To Boot the Solaris Operating System” on page 39 . 13. Install any required patch or patches to the server. Refer t...

Chapter 1 Preparing for Installation 7 Cable Management Notes A cable management bracket ( FIGURE 1-4 ) is included in the server slide rail kit. The cable management bracket clips onto the slide rails. Use cable ties or cable straps toattach cabling to the bracket. FIGURE 1-4 Cable Management Brack...

8 SPARC Enterprise T1000 Server Installation Guide • April 2007 Data Port and Cabling Notes Port Locations FIGURE 1-5 shows the ports on the server. FIGURE 1-5 Locations of Ports and Connectors on the Rear Panel Cabling Notes The following list describes the server ’s cable connections and ports: ■ ...

Chapter 1 Preparing for Installation 9 ■ Ethernet ports. The server Ethernet interfaces operate at 10 Mbps, 100 Mbps, and 1000 Mbps. The transfer rates for the Ethernet ports are given in TABLE 1-1 . ■ TTYA serial port. Use the DB-9 connector with a null modem cable for serial devices. This port app...

11 C H A P T E R 2 Installing the Server This chapter provides instructions for installing the server in an equipment rack.This chapter contains the following sections: ■ “Rackmount Kit” on page 11 ■ “Installing the Server in a Rack” on page 12 ■ “Removing the Server From the Rack for Service” on pa...

12 SPARC Enterprise T1000 Server Installation Guide • April 2007 Installing the Server in a Rack ▼ To Install the Mounting Brackets 1. Pull both mounting brackets completely out of their respective slide rails. a. Simultaneously press and hold the upper and lower lock buttons of the slide rail lock ...

Chapter 2 Installing the Server 13 FIGURE 2-2 Mounting Bracket Release Button 2. Attach a mounting bracket to the right side of the server chassis. a. Position the mounting bracket against the server chassis ( FIGURE 2-3 ) so that the slide rail lock is at the front and the two keyed openings on the...

14 SPARC Enterprise T1000 Server Installation Guide • April 2007 FIGURE 2-3 Attaching a Mounting Bracket to the Chassis b. With the heads of the two locating pins protruding though the two keyed openings in the mounting bracket, slide the mounting bracket toward the frontof the chassis until the bra...

Chapter 2 Installing the Server 15 ▼ To Install the Slide Rails 1. Determine which rack hole numbers you will use when attaching the slide rails to the rack posts. Most racks have posts that are marked off by rack units (1.75 in. or 45 mm). Theserver occupies one rack unit. 2. Determine which screws...

16 SPARC Enterprise T1000 Server Installation Guide • April 2007 4. Determine if the slide rails require an extension bracket. Most rack installations do not require slide rail extension brackets. However, youmay need to install the extension brackets under the following conditions: ■ If your rack i...

Chapter 2 Installing the Server 17 5. Attach a slide rail to the right front rack post ( FIGURE 2-6 ). a. Loosely attach the front of a slide rail to the right front rack post using two screws (M5 or M6, as appropriate to the size of the screw holes on the rackpost). Do not tighten the screws yet. F...

18 SPARC Enterprise T1000 Server Installation Guide • April 2007 a. At the rear of the rack, insert the left side of the tool into slots at the end of the middle section on the left slide rail ( FIGURE 2-7 ). FIGURE 2-7 Using the Slide Rail Spacing Tool to Adjust the Distance Between the SlideRails ...

Chapter 2 Installing the Server 19 e. At the front of the rack, use the spacing tool to adjust the distance between the front ends of the rails. The front ends of the rails do not have slots for the spacing tool. Slide the railssideways as needed until the sides of the spacing tool touch both rails....

20 SPARC Enterprise T1000 Server Installation Guide • April 2007 2. Raise the server and insert the ends of the mounting brackets into the left and right slide rails ( FIGURE 2-8 ). FIGURE 2-8 Mounting the Chassis on the Slide Rails 3. Slide the chassis into the rack. Caution – Before continuing, ve...

Chapter 2 Installing the Server 21 Note – When you attach cables to the server, as in the following procedures, lay the cables over the cable management bracket, then use cable ties to hold each cable inplace. Removing the Server From the Rack forService To install or replace internal parts in the s...

22 SPARC Enterprise T1000 Server Installation Guide • April 2007 ▼ To Connect the SC Serial Management Port The system controller serial management port is marked SER MGT ( FIGURE 2-10 ). FIGURE 2-10 System Controller Serial and Network Ports, Rear of Chassis Note – Use the SC serial management port...

Chapter 2 Installing the Server 23 ▼ To Connect the Ethernet Network Cables The server has four network connectors, marked NET0, NET1, NET2, and NET3( FIGURE 2-9 ). These connectors are RJ-45 Gigabit Ethernet. 1. Connect a Category 5 cable from your network switch or hub to Ethernet Port 0 ( NET 0) ...

25 C H A P T E R 3 Powering On the System This chapter includes instructions for booting the server and for enabling the systemcontroller network management port. The following topics are discussed: ■ “Powering On the Server for the First Time” on page 25 ■ “Logging In To the ALOM CMT System Control...

26 SPARC Enterprise T1000 Server Installation Guide • April 2007 Note – To see these status and error messages, connect a terminal or terminal emulator to the serial management port (SERIAL MGT). For a basic procedure toconnect a terminal or terminal emulator, see “To Power On the System for the Fir...

Chapter 3 Powering On the System 27 ▼ To Power On the System for the First Time Tip – The serial terminal or a terminal emulator should be connected before you connect the power cable, or you will not see the system messages. The server goesinto standby mode and the ALOM CMT system controller initia...

30 SPARC Enterprise T1000 Server Installation Guide • April 2007 1. If this is the first time the system has been powered on, use the password command to set the admin password. After the admin password has been set, on subsequent reboots, the sc login prompt is displayed. 2. Enter admin for the log...

Chapter 3 Powering On the System 31 Note – If you are unable to use DHCP and SSH on your network, you must connect to the ALOM CMT system controller using the serial management port toreconfigure the network management port. See “To Configure the System Controller Network Management Port” on page 31...

32 SPARC Enterprise T1000 Server Installation Guide • April 2007 You set these network parameters according to the specific details of your networkconfiguration: ■ if_network – Specifies whether the SC is on the network or not ■ netsc_ipaddr – IP address of the system controller ■ netsc_ipgateway – ...

Chapter 3 Powering On the System 33 a. Set the IP address for the system controller. b. Set the IP address for the system controller gateway. c. Set the netmask for the system controller. This example uses 255.255.255.0 to set the netmask. Your network environment subnet might require a different ne...

34 SPARC Enterprise T1000 Server Installation Guide • April 2007 Note – After setting the configuration parameters, you must reset the system controller for the new values to take affect. See “To Reset the System Controller” on page 34 . ▼ To Reset the System Controller ● Issue the resetsc command. ...

36 SPARC Enterprise T1000 Server Installation Guide • April 2007 ▼ To Initiate the Power On Sequence Powering on the system requires you to use the poweron command at the SC console. ● To initiate the power-on sequence, issue the poweron command. You see an sc> alert message on the system console...

Chapter 3 Powering On the System 37 ▼ To Perform a Normal System Initialization After you issue the poweron command, the CPU and memory controllers initialize and eventually OpenBoot initializes. After a number of system messages, the ok prompt appears. The example output below is a small section of...

Chapter 3 Powering On the System 39 Booting the Solaris Operating System The Solaris OS is preinstalled on the disk drive (for server configurations thatinclude a hard drive). The Solaris OS is not configured. If you boot the server fromthis drive, you will be prompted to configure the Solaris OS fo...

40 SPARC Enterprise T1000 Server Installation Guide • April 2007 ▼ (Optional) To Reset the System ● If it is necessary to reset the system, use the init 6 command. Note – Do not power the system off and on. ▼ To Power Cycle the System If a simple reset does not clear a system problem, you can power ...

Chapter 3 Powering On the System 41 4. Type the poweron command. 5. Reconnect to the system console using the console command. The systems displays various messages, followed by the ok prompt. sc> poweron sc> SC Alert: Host System has Reset sc> console -f Enter #. to return to ALOM.

43 A P P E N D I X A Updating the Server Firmware This appendix describes how to update the server firmware. This appendix includes the following topics: ■ Flash Image Overview ■ Updating the Firmware Flash Image Overview The flash image consists of the following components: ■ System controller firm...

44 SPARC Enterprise T1000 Server Installation Guide • April 2007 ▼ To Update the Firmware 1. Ensure that the ALOM CMT system controller network management port is configured. This is required to access the new flash image over the network. See “To Configure the System Controller Network Management P...

47 A P P E N D I X B Selecting a Boot Device The boot device is specified by the setting of an OpenBoot configuration variablecalled boot-device . The default setting of this variable is disk net . Because of this setting, the firmware first attempts to boot from the system hard drive, and ifthat fa...

50 SPARC Enterprise T1000 Server Installation Guide • April 2007 ■ netsc_ipnetmask – Netmask for the system controller subnet Note – For more information on configuring ALOM CMT, refer to the Advanced Lights Out Management (ALOM) CMT Guide. To configure these parameters you must use the setsc comman...

53 Index Symbols #. , system console escape sequence, 40 A AC power cable, 9AC power, system controller, 4adapters for serial cables, 22adjusting length of slide rails, 15 admin command for firmware update, 44 admin password, setting, 30 admin user account, 29 ALOM CMT 60 second timeout if not logge...