Fujitsu PRN607-S - Manuals

MAN607-S 28-03-2003 Page 2-14 of 53 64 through 256 dots can, however, are set using the command for setting the number of dynamic division dots. When the maximum number of activated dots is 128 dots, and all of the dots are driven, as shown in 2.6.6 Head Control Circuit The PRN607-S has a function f...

MAN607-S 28-03-2003 Page 3-15 of 53 3 Specifications Default settings Interface Serial RS232C, USB or IRDA Data format serial 115.200 baud, 8 data bit, none parity, 1 stop bit, hardware handshake. Baud rate can be changed by software. Data format USB USB Printer class specification. http://www.usb.o...

MAN607-S 28-03-2003 Page 4-16 of 53 4 Function 4.1 General Notice, when data is sent from the external equipment to the printer controller, all data has to be sent as binary file. If data is being sent as a character file, and some data in the file is equal to EOF, the rest will not be received. 4.2...

MAN607-S 28-03-2003 Page 4-17 of 53 4.5 Firmware upgrade. If firmware needs to be changed, alternative firmware can be downloaded. Please contact I/F-COM for firmware upgrade or changes. The steps to download an alternative firmware in DOS are the following. These steps only work for a serial connec...

MAN607-S 28-03-2003 Page 4-18 of 53 4.7 Character design The following figures describes the design of different types of characters (small): 4.7.1 Normal Character. 4.7.2 Low Character 4.7.3 Underline When underline characters are printed the last line in the character matrix will be marked. 4.7.4 ...

MAN607-S 28-03-2003 Page 4-20 of 53 4.8 Printer commands I/F-COM simple command set is default command set however optional command set can be downloaded. See appendix for additional information. 4.9 I/F-COM simple command set. The following commands are use when communicating with the printer contr...

MAN607-S 28-03-2003 Page 4-30 of 53 Code128 barcode table ‘d’ A B C ‘d’ A B C 0 Space Space 0 52 T T 52 1 ! ! 1 53 U U 53 2 “ “ 2 54 V V 54 3 # # 3 55 W W 55 4 $ $ 4 56 X X 56 5 % % 5 57 Y Y 57 6 & & 6 58 Z Z 58 7 ‘ ‘ 7 59 [ [ 59 8 ( ( 8 60 \ \ 60 9 ) ) 9 61 ] ] 61 10 * * 10 62 ^ ^ 62 11 + +...

MAN607-S 28-03-2003 Page 5-34 of 53 5 Maintenance 5.1 Daily use Printer and interface board must be switch off while in idle mode. 5.2 Store/Transport The product has to be stored under ESD safe conditions, and to be packed safely during transportation.

MAN607-S 28-03-2003 Page 6-35 of 53 6 Specifications 6.1 Electrical Data Voltage: 18-26VDC Current: Maximum head current:Numbers of active dots * Vhead 1.500+/-15% Maximum motor current: 1.000mA Power up sequence: max. 10 msec. 10 – 90% Voltage applied Power down sequence: max. 10 msec. 90 – 10% Vol...

MAN607-S 28-03-2003 Page 6-36 of 53 6.5 Temperature Test Temperature shock: (no voltage applied) -28°C to +100°C at 1 sec. 100 times: no damage.

MAN607-S 28-03-2003 Page 6-39 of 53 The paper near end status, can be seen on the LED on the aux connector, it can be reading through the status command, and if a driver is used, then it can be reading in the port monitor: If paper jam is used, then will the printer stop printing if this signal is g...

MAN607-S 28-03-2003 Page 6-41 of 53 6.7 Mechanical Drawings

MAN607-S 28-03-2003 Page 7-42 of 53 7 Appendix 7.1 Seiko compatible command set 7.1.1 Escape sequences, overview. CR CR Carriage Return ESC+ ‘ J ’ +n Print and Feed Forward ESC+ ‘ j ’ +n Print and Feed Backward ESC+ ‘ 2 ’ 16-dot Line Spacing ESC+ ‘ 0 ’ 4-dot Line Spacing ESC+ ‘A’+n or ESC+ ‘3’+n n-d...

MAN607-S 28-03-2003 Page 7-43 of 53 DC3+ ‘ + ’ Ruler Line ON DC3+ ‘ - ’ Ruler Line OFF DC3+ ‘ P ’ Print One Dot Line after Printing Line Buffer Data DC3+ ‘ C ’ Ruler Line Buffer Clear DC3+ ‘ (’ Continuous Ruler Line Control Code Input 7.2 Fujitsu compatible command set 7.2.1 Escape sequences, overvi...

MAN607-S 28-03-2003 Page 7-44 of 53 FS 9+n Detection function enable/disable setting FS C+n Kanji code system selection FS W+n Kanji double height and width mode specification/cancellation GS < Mark detection execution GS A+m+n After-mark-detection head detection distance setting GS E+n Print qua...

MAN607-S 28-03-2003 Page 7-47 of 53 7.4 APS compatible command set 7.4.1 Escape sequences, overview. GS / n Set printing speed / Maximum peak current GS D n Set print Intensity ESC v Send printer status ESC I Send printer identity ESC @ Resets printer ESC S Puts the printer in sleep mode GS B n Seri...