Fujitsu MB96300 - Manuals

Fujitsu MB96300 – Manual in PDF format online.

Manuals:

Manual

Manual Fujitsu MB96300

Summary

Page 2 - Revision History; Date

SK-96370-144PMC-GDC User Guide Revision History FMEMCU-UG-960014-10 - 2 - © Fujitsu Microelectronics Europe GmbH Revision History Date Issue 20.05.2008 V1.0, HWe, First Release This document contains 42 pages.

Page 3 - Warranty and Disclaimer

SK-96370-144PMC-GDC User Guide Warranty and Disclaimer © Fujitsu Microelectronics Europe GmbH - 3 - FMEMCU-UG-960014-10 Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-96370-144PMC-G...

Page 4 - Contents

SK-96370-144PMC-GDC User Guide Contents FMEMCU-UG-960014-10 - 4 - © Fujitsu Microelectronics Europe GmbH 0 Contents REVISION HISTORY ............................................................................................................ 2 WARRANTY AND DISCLAIMER ...................................

Page 6 - Overview

SK-96370-144PMC-GDC User Guide Chapter 1 Overview FMEMCU-UG-960014-10 - 6 - © Fujitsu Microelectronics Europe GmbH 1 Overview 1.1 Abstract The SK-96370-144PMC-GDC is a multifunctional evaluation board for the Fujitsu 16FX Flash microcontroller MB96370 Series. It can be used stand-alone for software ...

Page 7 - This board must only be used for test applications

SK-96370-144PMC-GDC User Guide Chapter 1 Overview © Fujitsu Microelectronics Europe GmbH - 7 - FMEMCU-UG-960014-10 1.2 Features < Supports Fujitsu’s 16FX MB96370 Series with 144 pin PMC / M08 package or the MB2198 Emulator System with the Probe Cable MB2198-507-E. < 9-15V unregulated external ...

Page 8 - Description; C, internal clock rates up to 56 MHz can be achieved.

SK-96370-144PMC-GDC User Guide Chapter 1 Overview FMEMCU-UG-960014-10 - 8 - © Fujitsu Microelectronics Europe GmbH 1.3 General Description The SK-96370-144PMC-GDC supports the F 2 MC-16FX microcontrollers of MB96370 Series with LQFP144-M08 (PMC) package. It can be used as a stand-alone evaluation bo...

Page 10 - Installation; Carefully remove the board from the shipping carton.

SK-96370-144PMC-GDC User Guide Chapter 2 Installation FMEMCU-UG-960014-10 - 10 - © Fujitsu Microelectronics Europe GmbH 2 Installation 2.1 Connection/Power-On Carefully remove the board from the shipping carton. First, check if there are any damages before powering up the evaluation board. For the p...

Page 11 - Default Jumper settings for MB96370 Series; Jumper

SK-96370-144PMC-GDC User Guide Chapter 2 Installation © Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-960014-10 2.2 Default Jumper settings for MB96370 Series The following table lists all jumpers including its default setting and location on the starterkit. Jumper Description / Function Typ...

Page 13 - Location

SK-96370-144PMC-GDC User Guide Chapter 2 Installation © Fujitsu Microelectronics Europe GmbH - 13 - FMEMCU-UG-960014-10 2.3 Jumper Location The following picture shows the silk plot of the starter-kit with marked default jumper settings. A B C D E F G H I J K L M 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 ...

Page 14 - Jumpers and Switches; This switch controls the MCU operation mode after Reset.; DIP switch; Not connected

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches FMEMCU-UG-960014-10 - 14 - © Fujitsu Microelectronics Europe GmbH ON OFF DIP-Switch S1 (RUN Mode) MD0 MD1 MD2 nc 1 2 3 4 ON OFF DIP-Switch S1 (Programming Mode) MD0 MD1 MD2 nc 1 2 3 4 3 Jumpers and Switches This chapter describes all jump...

Page 15 - Supply

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches © Fujitsu Microelectronics Europe GmbH - 15 - FMEMCU-UG-960014-10 3.2 Power Supply (S2, JP: 8, 15, 16, 17, 22) The on-board voltage regulator provides stabilized 5V *1 and 3.3V supplies to the MCU *1 and peripherals. Even though they are ...

Page 16 - Please check the related datasheet.

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches FMEMCU-UG-960014-10 - 16 - © Fujitsu Microelectronics Europe GmbH 3.3 Subclock (JP: 1, 2) Some devices like e.g. MB96F37xRW support a 32 kHz sub-clock (X0A, X1A), other devices like e.g. MB96F37xRS do not support a sub-clock but will offe...

Page 17 - Comparator

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches © Fujitsu Microelectronics Europe GmbH - 17 - FMEMCU-UG-960014-10 3.4 Analog Power Supply Voltage (JP: 11, 12, 13, 14) The power supply as well as the positive reference voltage for the A/D-converter can be provided internally or external...

Page 18 - Generation

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches FMEMCU-UG-960014-10 - 18 - © Fujitsu Microelectronics Europe GmbH 3.6 Reset Generation (JP: 33, 41, 46, 47, 48) In addition to the internal Power-On reset, the microcontroller can be reset by an external reset circuit (Voltage Monitor) an...

Page 22 - External Flash memory; Table 3-10: External Flash Configuration; External SRAM memory

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches FMEMCU-UG-960014-10 - 22 - © Fujitsu Microelectronics Europe GmbH 3.11 External Flash memory (JP: 49, 52, 56) The SK-96370-144PMC-GDC is equipped with an additional 8 MByte Flash memory connected to the external bus interface. JP49 Select...

Page 23 - Graphic Display Controller interface

SK-96370-144PMC-GDC User Guide Chapter 3 Jumpers and Switches © Fujitsu Microelectronics Europe GmbH - 23 - FMEMCU-UG-960014-10 3.13 Graphic Display Controller interface (JP: 54, 55, 56, 57, 58, 60, 85, 86) The SK-96370-144PMC-GDC provides the external bus interface on the two connectors X10 and X11...

Page 24 - Connectors; connector; Pin Number

SK-96370-144PMC-GDC User Guide Chapter 4 Connectors FMEMCU-UG-960014-10 - 24 - © Fujitsu Microelectronics Europe GmbH 4 Connectors 4.1 Power connector (X7) The following figure shows the power connection jack X7. This connector is used to connect an external unregulated DC power supply voltage (9V-1...

Page 25 - Connector

SK-96370-144PMC-GDC User Guide Chapter 4 Connectors © Fujitsu Microelectronics Europe GmbH - 25 - FMEMCU-UG-960014-10 4.4 CAN Connector (X6, X8) Two 9-pin D-Sub male connectors are used for the CAN interfaces CAN0 and CAN1. Both CAN interfaces can be used simultaneously. Figure 4-3: CAN Connector Pi...

Page 26 - The following control signals are provided:

SK-96370-144PMC-GDC User Guide Chapter 4 Connectors FMEMCU-UG-960014-10 - 26 - © Fujitsu Microelectronics Europe GmbH 4.5 USER-LEDs & optional LC-Display (J1) Eight LEDs are supplied for user applications. In order to disconnect the LEDs from the related microcontroller port (Port P09), the resi...

Page 29 - Programming the internal Flash memory; Mode

SK-96370-144PMC-GDC User Guide Chapter 5 Programming the internal Flash memory © Fujitsu Microelectronics Europe GmbH - 29 - FMEMCU-UG-960014-10 5 Programming the internal Flash memory All Flash devices have an internal bootloader for asynchronous- as well as for synchronous- Flash-programming: <...

Page 30 - Reset

SK-96370-144PMC-GDC User Guide Chapter 5 Programming the internal Flash memory FMEMCU-UG-960014-10 - 30 - © Fujitsu Microelectronics Europe GmbH ON OFF DIP-Switch S1 (Programming Mode) MD0 MD1 MD2 nc 1 2 3 4 5.1.3 Reset (optional) Depending on the programming software a reset signal might be generat...

Page 31 - ) Power on the board. The user application is started directly.; X4: Flash programming socket

SK-96370-144PMC-GDC User Guide Chapter 5 Programming the internal Flash memory © Fujitsu Microelectronics Europe GmbH - 31 - FMEMCU-UG-960014-10 ON OFF DIP-Switch S1 (RUN Mode) MD0 MD1 MD2 nc 1 2 3 4 4) After programming the Flash-device, switch off the power supply and set back the mode according t...

Page 32 - Appendix; Products

SK-96370-144PMC-GDC User Guide Chapter 6 Appendix FMEMCU-UG-960014-10 - 32 - © Fujitsu Microelectronics Europe GmbH 6 Appendix 6.1 Related Products < SK-96370-144PMC-GDC Evaluation board for the MB96F37xxxPMC MCU in FPT-144P-M08 (LQFP-144) package including external memory and GDC connector < ...

Page 33 - Information in the WWW; Power Management Products

SK-96370-144PMC-GDC User Guide Chapter 7 Information in the WWW © Fujitsu Microelectronics Europe GmbH - 33 - FMEMCU-UG-960014-10 7 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Microcontrollers (8-, 16- and 32bit), Graphics ...

Page 34 - China-RoHS regulation; Emulation Board; Explanation of Pollution Control Label

SK-96370-144PMC-GDC User Guide Chapter 8 China-RoHS regulation FMEMCU-UG-960014-10 - 34 - © Fujitsu Microelectronics Europe GmbH 8 China-RoHS regulation Evaluation Board Emulation Board SJ/T11364-2006 The following product pollution control information is provided according to SJ/T11364-2006 Marking...

Page 35 - Table of hazardous substances name and concentration

SK-96370-144PMC-GDC User Guide Chapter 8 China-RoHS regulation © Fujitsu Microelectronics Europe GmbH - 35 - FMEMCU-UG-960014-10 In order to maintain the declared EFUP, the product shall be operated normally according to the instructions and environmental conditions as defined in the product manual,...

Page 36 - Recycling; Fujitsu Microelectronics Europe GmbH; Valid for European Union Countries:; For disposal please send the device to the following address:

SK-96370-144PMC-GDC User Guide Chapter 9 Recycling FMEMCU-UG-960014-10 - 36 - © Fujitsu Microelectronics Europe GmbH 9 Recycling Gültig für EU-Länder: Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische Gesetze nehmen wir dieses Gerät wieder zurück. Zur Entsorgung schicke...