Fujitsu MB2198-01 - Manuals

Fujitsu MB2198-01 – Manual in PDF format online.

Manuals:

Manual

Manual Fujitsu MB2198-01

Summary

Page 2 - PREFACE; Purpose and intended readership of this manual; Precautions When Using this Product; Warranty and liability

i PREFACE ■ Purpose and intended readership of this manual Thank you for purchasing the LQFP-176P Header Type 3 for the DSU-FR Emulator (MB2198-301) .This product is used together with the BGA-660P adapter for the DSU-FR Emulator (MB2198-300) * 1 to connect the DSU-FR Emulator (MB2198-01) * 2 and FR...

Page 3 - ii; Caution of the products described in this document

ii ■ Caution of the products described in this document The following precautions apply to the product described in this manual. WARNING Indicates a potentially hazardous situation which, if not avoided appropriately, could result in death or serious injury and/or a fault in the user’s system. Elect...

Page 5 - Check package contents; Header board attachment screws

1 1. Product Overview 1.1 Overview This product is an option product for use with the DSU-FR emulator and is intended to support thedevelopment of user systems that use the Fujitsu FR family of microcontrollers.The main features of the header board are as follows. • Used in conjunction with the adap...

Page 7 - System Configuration; AC in

3 1.4 System Configuration The header board is used together with an emulator, adapter, and other components to connect to theuser system.Figure1.1 shows the system configuration to this product. Figure 1.1 System Configuration To use the emulator, a host computer and emulator/debugger software are ...

Page 8 - External View and Names of Each Part

4 1.5 External View and Names of Each Part Figure 1.2 shows the external view of the header board and the names of each part.Note that Figure 1.2 shows the state of the header board when it is shipped. Figure 1.2 External View of Header Board 2 1 10 9 8 7 6 5 4 3 No. Part No. Part ➀ Adapter I/F conn...

Page 9 - Precautions When Using this Product; Precautions; Please follow this manual about setting and using the adapter.

5 2. Precautions When Using this Product Take the precautions and restrictions below when using the header board. ■ Precautions • Operating the device outside the range of any general specification may cause the device to malfunction. Use the device in the ranges of its general specifications. • Ple...

Page 10 - Points to note when designing the MCU foot pattern; Figure 2.2 Foot Pattern Dimensions for Mounting the NQPACK; Restrictions; The following general restrictions apply to the header board.; holes are not required if not using the guide pins.; mm

6 ■ Points to note when designing the MCU foot pattern The figure shows the recommended foot pattern dimensions for mounting the NQPACK on the print-ed circuit board for the user system. Please take account of the NQPACK foot pattern requirementsas well as the recommended foot pattern for the mass p...

Page 11 - Connecting the Header Board to the User System; Connection procedure; ) on the header board; TET; NQPACK

7 3. Connection 3.1 Connecting the Header Board to the User System Mount the supplied NQPACK on the user system before using the header board. The header board is used together with the adapter.Refer to the hardware manual for the adapter for details about how to connect the header board andadapter....

Page 12 - Disassembly procedure

8 Figure 3.2 Header Board Connection Procedure ■ Disassembly procedure To remove the header board, first remove the four screws and then lift the header board verticallyup/off the NQPACK. Header board attachment screws Washers Header board User system YQPACK NQPACK

Page 13 - Mounting a Mass Production MCU Model; Align the index mark on the mass production MCU (

9 3.2 Mounting a Mass Production MCU Model Use the supplied HQPACK to mount the mass production MCU in the user system. 1. Align the index mark on the mass production MCU ( ● ) with the index mark on the NQPACK mounted on the user system ( ▲ ), and then insert. 2. Check that the mass production MCU ...

Page 14 - Jumper Plug Settings; VCC5 jumper plug setting; Figure 4.1 VCC5 Jumper Plug Settings; NC; Setting

10 4. Operation The following describes how to set the various settings, and the procedure for turning the power onand off. Be sure to read the setting as shown below before turning on the power. 4.1 Jumper Plug Settings ■ VCC5 jumper plug setting Figure 4.1 shows the factory setting and setting mea...

Page 15 - VCCB1 to VCCB5 settings

11 ■ VCCB1 to VCCB5 settings Figure 4.2 describes the factory setting of VCCB1 to VCCB5 jumper plugs and the setting of thejumper plugs. Figure 4.2 VCCB1 to VCCB5 Jumper Plug Settings VCC5H VCC3H S4 VCCB4 VCC5H VCC3H S3 VCCB3 VCC5H VCC3H S2 VCCB2 VCC5H VCC3H S1 VCCB1 VCC5H VCC3H S5 VCCB5 Jumper plug...

Page 16 - Use of pull-up resistor

12 For method to select each jumper plug, when the power supply connected to VCC3 is 3.3 V ± 0.3 V, VCCB5 should be set to VCC3H. In this case, the jumper plugs corresponding to the VCC5 pins that have a power supply with a voltage different to VCC3 (5 V ± 10 %) should be set to VCC5H. The jumpers f...

Page 17 - General specifications; Table 5.1 General Specifications

13 5. Specifications 5.1 General specifications Table 5.1 lists the general specifications of the header board. Table 5.1 General Specifications Note : The operating voltage range may be differed for some evaluation MCUs. Item Specification Remarks Product name (model no.) LQFP-176P Header Type 3 (M...

Page 18 - Function Specifications; Table 5.2 lists the function specifications of the header board.

14 5.2 Function Specifications Table 5.2 lists the function specifications of the header board. Table 5.2 Function Specifications of Header Board Item Specification Header board Connects the user system and adapter. Level shift function The header board includes a level shifter used to convert the V...

Page 19 - Figure 5.1 Grouping for Level Shift Function; TOP View; Level shift

15 Figure 5.1 Grouping for Level Shift Function 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 160 159 158 157 156 155 154 153 152 151 150 149 148 147 145 144 143 142 141 140 139 138 137 136 135 134 133 2 131 3 130 4 129 5 128 6 127 7 126 8 125 9 124 10 123 11 122 12 121120 14 119 15 11...

Page 20 - Connector Specifications; YQPACK specifications; VCC3 connects to the VCC3 pin on the mass production MCU.

16 5.3 Connector Specifications ■ YQPACK specifications On the header board, the signals from the evaluation MCU mounted on the adapter are connected inaccordance with the mass production MCU pin layout (same layout as YQPACK) via the two adapt-er interface connectors on the header board.Refer to th...

Page 25 - FUJITSU SEMICONDUCTOR; SUPPORT SYSTEM; FUJITSU LIMITED Electronic Devices; Edited

SS01-71050-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM DSU-FR EMULATORLQFP-176P HEADER TYPE 3MB2198-301OPERATION MANUAL December 2005 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.