Fujitsu M3097G+ - Manuals

iv CHAPTER 5 MAINTENANCE ......................................................................................... 5-1 5.1 Removing Jammed Documents ................................................................................... 5-1 5.2 Notes on Daily Use ...........................................

v FIGURES page Figure 2.1 Received components ...................................................................................... 2-1 Figure 2.2 M3097E+/G+ parts names ............................................................................... 2-2 Figure 2.3 M3097E+ operator panel ..............

vi TABLES page Table 1.1 The differences between the M3097E+ and the M3097G+ ............................. 1-1 Table 6.1 Check items ..................................................................................................... 6-1 Table A.1 Installation specifications ..........................

2 – 1 CHAPTER 2 COMPONENTS 2.1 Checking the Components 2.2 Part Names and Functions 2.3 Operator Panel Functions After unpacking image scanner, confirm that all the components have been received. Thissection describes the components of the image scanner and their functions. 2.1 Checking the Componen...

2 – 2 2.2 Part Names and Functions This section shows the exterior view of image scanner. This sectionalso provides names of each part and describes their functions. 2.2.1 Exterior view of image scanner The image scanner can read a document of A3 or double-letter size atmaximum. ADF paper chute Powe...

2 – 3 2.2.2 Functions of each part Document cover: Closed over and holds a document to beread. Document bed: A document to be read is placed on thebed also called Flatbed (FB). Document holding pad: Presses a document to the document bed. Automatic document feeder (ADF): Automatically feeds document...

2 – 4 2.3 Operator Panel Functions The operator panel has indicators and a liquid crystal display screenfor displaying image scanner status. The operator panel also hasoperation buttons. Mode 1 Mode 2 Liquid crystal display screen Buttons Indicators Power Read Check Figure 2.4 M3097G+ operator panel...

2 – 5 2.3.1 Indicators The meaning of each indicator is as follows: Power indicator (Green): Lights to indicate the power is on. Ready (for reading) indicator (Green) (M3097E+): Lights when the image scanner becomes ready to read a docu-ment in the manual mode. This indicator turns off when thestart...

2 – 6 Liquid crystal display screen The screen has two message lines. The current read modestatus is displayed in the upper line, and messages and themodes set by the buttons are displayed in the lower line. FlatbedAutomatic document feeder Reading mode Display : FB: ADF    Size Double-letter siz...

2 – 7 The ADF, size, density, resolution, landscape, half-tone, document,and mode 1 and 2 buttons described below are effective unless other-wise specified by the host system. Automatic document feeder (ADF) button: Selects whether to feed documents automatically by ADF ormanually on the flatbed. Wh...

2 – 8 Density button: Selects a density for the read operation. When this button ispressed, the lower line is displayed as shown in Screen 3. Eachtime this switch is pressed, the blinking part in the lower linechanges, and the density indicated on the upper line changesaccording to the blinking part...

2 – 10 Document button: Selects the type of document. When this button is pressed, thelower line is displayed as shown in Screen 7. Each time thisbutton is pressed, “LINE” or “PHOTO” starts blinking in turn,and the document selection indication displayed on the upperline changes accordingly. Screen ...

2.3.3 Buttons and liquid crystal display screen (M3097G+) Liquid crystal display screen: Displays messages only. The mode buttons have the following functions: Mode 1 button: See Section 5.3.4, 5.4 and 5.5.Mode 2 button: See Section 5.3.4, 5.4 and 5.5. When error messages are displayed on liquid cry...

3 – 1 CHAPTER 3 INSTALLATION AND CONNECTIONS Place the scanner away from electrical noisesources and strong magnetic fields. If theimage scanner is used near an air conditioner,copying machine, or TV set, the scanner mayoperate incorrectly. Keep the scanner out of the sun and awayfrom heaters. These...

3 – 2 3.2 Removing the Carrier Fixing Bracket To keep the scanner from being damaged during shipping, the carrierunit is fixed with a bracket. After placing the carrier unit at theinstallation place, remove this bracket as explained below. 1 Place the image scanner on the edge of the desk top so tha...

3 – 3 3.3 Connections Connect the image scanner using the following procedure. 1 Set the power switch to off. 3 Connect the interface cables (for M3097E+). Connect the interface cables to the interface connectors and fasten the cableswith catches and screws as shown below.Connect the other end of ea...

3 – 5 3.4 Mounting the Stacker Mount the stacker and extensions using the following procedure. 1 Mount the stacker. Hook the pins on the stacker to the claws on the image scanner. 2 Mount the extensions. Mount extensions to the stacker and to the ADF paper chute. Stacker Pin Claw Extension Stacker E...

4 – 1 CHAPTER 4 OPERATIONS 4.1 Turning on the Power 4.2 Reading a Document in Flatbed Mode 4.3 Reading Documents in ADF Mode Documents can be read in the flatbed mode or automatic document feeder (ADF) mode. In theflat-bed mode, each document is placed on the document bed and is read one by one. In ...

4 – 2 4.2 Reading a Document in Flatbed Mode This section explains how to read a document placed on the documentbed. CAUTION ! High luminance: Do not look directly at the light source during read operation. Keep the document cover inplace. 4.2.1 Reading a standard-size document If the size of the do...

4 – 3 Landscape mode Portrait mode Long side Short side 3 3 Document bed Document Document cover Reference mark Operator panel Figure 4.1 Flatbed reading Document bed Document 4.2.2 Reading a page from a thick book To read a page from a thick book, remember the following points: 1 Do not close the d...

4 – 4 4.2.3 Reading a document larger than the document board If the size of the document is larger than the document board, read thedocument using the following procedure: 1 To remove the document cover, remove the screw from thedocument cover. 2 Place the document face down on the document bed. 3 ...

4 – 5 4.3 Reading Documents in ADF Mode This section explains how to read documents using the automaticdocument feeder. If the following steps are not closely followed, afeed error may occur.After documents have been read in ADF mode, a squeaking noise issometimes heard. This is not a problem as the...

4 – 6 2 Pull up the ADF paper chute as follows: • Hold the document cover with one hand and pull up the ADF paper chute with the other hand to unlock the ADF paper chute. ADF paper chute Document cover 3 Fan the documents as follows: • Take a 15 to 20 mm thickness of documents. Lightly hold both end...

4 – 8 6 Open the right and left guides of the ADF paper chute about 5mm wider than the document width. 7 Place the documents face down onto the ADF paper chute withthe top edges facing the automatic feeder hole. 8 Adjust the guides to the document sides. Skewing may occur ifthere is a gap between th...

5 – 1 5.1 Removing Jammed Documents 5.2 Notes on Daily Use 5.3 Cleaning 5.4 Replacing the Lamp Unit 5.5 SCSI Address Setting (M3097G+) 5.6 Replacing the Pad 5.7 Document counter display and reset CHAPTER 5 MAINTENANCE This section explains how to remove jammed documents, and provides notes on daily ...

5 – 2 5.2 Notes on Daily Use Note the following points on daily use: • The image scanner requires one to three minutes to warm up after the power has been turned on. During this time, the message“Warming-up Now!!” is displayed on the screen. • Do not look directly at the light source during the read...

5 – 3 5.3.2 Cleaning the ADF Clean the ADF once every 5,000 pages. The cycle depends on thetypes of documents used (page quality, a level of toner fusing onpaper).1 Pull the ADF lever up to open the ADF. 2 Use the dry cloth or a cloth with ethyl alcohol to softly removedirt and dust as follows.Pad: ...

5 – 4 5.3.3 Cleaning the coupled feed roller 1 Pull the ADF lever up to open the ADF. 2 Pull the ADF lamp replacement lever up while pushing the leverin the direction indicated by the arrow in Figure 5.4. 3 Clean the surface of the coupled feed roller by the cloth withethyl alcohol. NOTICE If the co...

5 – 5 5.4 Replacing the Lamp Unit Hot: Replace the lamp unit in the following procedure. If an optical alarm occurs, and the following message is displayed,replace the lamp unit as follows. c i t p l A a r a O m l • Turn off the power once. Then, turn on the power while pressing the mode 1 button. F...

5 – 6 • Pull the ADF lever up and open the ADF. • Pull the ADF lamp replacement lever up while pushing the lever in the direction indicated by the arrow in Figure 5.4. • Hold the lamp unit levers and pull the glass up. Wipe the bottom surface of the glass if it is dirty. ADF lamp replacement lever L...

5 – 7 A 2 A Lamp unit Lamp unit levers Lamp unit insertdirection (vertical) Arrows indicating the lamp unit insert position 1 Figure 5.6 Lamp unit replacement • Obtain a new lamp unit. • Hold the new lamp unit with both hands. Insert it in the insertion slits with the back end first and the front an...

5 – 8 Glass Levers Openings Figure 5.7 Inserting the glass • Close the ADF to lock ADF lever.

5 – 10 5.6 Replacing the pad (1) Pull up the ADF open and close lever to open the ADF.(2) Remove the four screws shown in Figure 5.8 to remove the two pads. (3) Install the pad by reversing the removal procedure. Figure 5.8 Removing the pad NOTICE Attach the pad so that the corner cut is top left. A...

5 – 11 5.7 Document counter display and reset The Document counter is useful for users to check the total number ofscanned documents before regular cleaning. This counter can bedisplayed or reset using the following procedures. (1) Turn on the power while holding down the Mode 1 button. The scanner ...

6 – 1 CHAPTER 6 TROUBLESHOOTING If a problem occurs, use Table 6.1 to resolve the problem. Table 6.1 Check items Problem No power Read operationdoes not start. Pictures andphotographs arenot read cor-rectly. Characters andlines are notread correctly. Image is dis-torted or un-clear. Possible cause T...

A – 1 APPENDIX A.1 Installation Specifications Table A.1 Installation specifications Specification Item External dimensions (mm) Weight (kg) Height 173 25 100 to 120 VAC, 220 to 240 VAC Single-phase 50/60 Hz 150 VA Input power Depth 497 Width 696 Voltage Number of phases Frequency Power Operation 5 ...

A – 2 A.2 External Dimensions 173 696 497 (Unit: mm) Figure A.1 External dimensions

We would appreciate your comments and suggestions for improving this publication. Thank you for your interest. Please send this sheet to one of the addresses in the left page. Publication No. Reader Comment Form How did yu use this publication? Learning Rev. Letter Title Current Date Reference Insta...