Fujitsu FLASH-CAN-100 - Manuals

Change even page title here Chapter 1 Overview UG-900001-32 - 6 - © Fujitsu Microelectronics Europe GmbH 1 Overview 1.1 Abstract This user guide describes the basic features of the new FLASH-CAN-100P-M06/FLASH-CAN2-100P-M06 board. This board can be used with almost all our 16LX microcontroller serie...

Change odd page title here Chapter 2 Features © Fujitsu Microelectronics Europe GmbH - 7 - UG-900001-32 2 Features < a new 100-pin socket adapter for better connectivity < 7-14V unstabilized external DC power supply possible < 5V and 3.7V internal power supply available < two high-speed ...

Change even page title here Chapter 3 Supported Microcontroller Series UG-900001-32 - 8 - © Fujitsu Microelectronics Europe GmbH 3 Supported Microcontroller Series The target board was designed to work with many microcontrollers from the F²MC-16LX family. As it allows the programming of blank flash ...

Change odd page title here Chapter 4 Deliverables © Fujitsu Microelectronics Europe GmbH - 9 - UG-900001-32 4 Deliverables "FLASH-CAN-100P-M06"/"FLASH-CAN2-100P-M06" will be delivered with: < the Flash/CAN100 board itself < two 50pin socket connectors < power supply connecto...

Change even page title here Chapter 5 Configuration of the Evaluation-Board UG-900001-32 - 10 - © Fujitsu Microelectronics Europe GmbH 5 Configuration of the Evaluation-Board The board is configured to work with the MB90F598 microcontroller. In order to set up the board follow these steps: 1. discon...

Change odd page title here Chapter 5 Configuration of the Evaluation-Board © Fujitsu Microelectronics Europe GmbH - 11 - UG-900001-32 7. Select the appropriate UART interface for the microcontroller you are using by setting jumper JP7-JP10. 8. Please use 1:1 cable for PC-connection. Notes: < Pixx...

Change even page title here Chapter 6 Using the Asynchronous Boot-Loader UG-900001-32 - 14 - © Fujitsu Microelectronics Europe GmbH 6 Using the Asynchronous Boot-Loader The asynchronous boot-loader SW from Fujitsu can be used to program a blank flash microcontroller. This tool is available on the fl...

Change odd page title here Chapter 7 Connectors © Fujitsu Microelectronics Europe GmbH - 15 - UG-900001-32 7 Connectors 7.1 Power connector (X1) The following figure shows the power connection jack X1. This connector is used to connect an external unregulated DC power supply voltage (9V-12V DC) to t...

Change even page title here Chapter 7 Connectors UG-900001-32 - 16 - © Fujitsu Microelectronics Europe GmbH 7.4 UART (X4) One 9-pin D-Sub female connectors are used for the serial interface (UART). TXD is the transmit output, RXD is the receive input. The DTR signal can be used to generate a reset. ...

Change odd page title here Chapter 8 Silk-Plot of the board © Fujitsu Microelectronics Europe GmbH - 17 - UG-900001-32 8 Silk-Plot of the board Silk Plot of the new FLASH-CAN2-100P-M06

Change even page title here Chapter 9 Schematic of the board UG-900001-32 - 18 - © Fujitsu Microelectronics Europe GmbH 9 Schematic of the board

Change odd page title here Chapter 10 Related Products © Fujitsu Microelectronics Europe GmbH - 19 - UG-900001-32 10 Related Products < FLASH-CAN-100P-M06 Evaluation-board according to this user guide < MB2132-457 Probe cable for socket: Yamaichi IC149-100-x14-y5 Yamaichi: http://www.yamaichi....

Change even page title here Chapter 11 Information in the WWW UG-900001-32 - 20 - © Fujitsu Microelectronics Europe GmbH 11 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Microcontrollers (8-, 16- and 32bit), Graphics Controll...