Fujitsu D2630 - Manuals

D2630 (RX600 S3) SAS 3 2 Important notes In this chapter you will find essential information regarding safety when working with the system board. V CAUTION! With the system board installed you must open the system to access the system board. How to dismantle and reassemble the system is described in...

4 D2630 (RX600 S3) SAS Notes on safety Important notes V ● Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns! ● Transmisson lines to peripheral devices must be adequately shielded. ● To the LAN w...

6 D2630 (RX600 S3) SAS CE Certificate Important notes Notes about boards ● During installation/deinstallation of the system board, observe the specific instructions described in the service manual for the server. ● Remove the plug from the mains outlet so that system and system board are totally dis...

D2630 (RX600 S3) SAS 7 Important notes Environment Protection 2.3 Environment Protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu Siemens Computers standard for “environmentally friendly product design and devel-opment”. Th...

D2630 (RX600 S3) SAS 9 Important notes Environment Protection Returning batteries Batteries which are marked with one of the following symbols may not be disposed of together with household refuse according to the applicable EU directive. Figure 3: Symbols for batteries With batteries containing har...

D2630 (RX600 S3) SAS 11 3 Features 3.1 Overview System board ● Up to four Intel ® XEON MP dual-core processors ● Intel ® E8501 chipset: – Intel ® E8501 chipset Nor thbridge (TNB): has two shared 64-bit FSB interfaces configured for symmetric multiprocessing. – External Memory Board (XMB): provides s...

14 D2630 (RX600 S3) SAS Main memory Features 3.2 Main memory The system board offers four slots for hot-plug memory boards. Each memory board can be equipped with up to four memory modules (in two memory banks). The slots for main memory can be populated with 1 Gbyte, 2 Gbyte or 4 Gbyte DDR II/400 M...

D2630 (RX600 S3) SAS 15 Features PCI bus 3.3 PCI bus Figure 5: PCI slots PCI slots The following table shows an overview of the PCI slots: Assignment of the PCI interrupts The PCI interrupts are assigned automatically by the BIOS and no further settings are possible. PCI slot Transfer rate Descripti...

16 D2630 (RX600 S3) SAS Screen resolution Features 3.4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the system board. If you are using an external screen controller, you will find details of suppor ted screen...

D2630 (RX600 S3) SAS 17 Features Temperature / system monitoring Fan monitoring Fans that are no longer available, blocked or sticky fans are detected. Fan control The fans are regulated according to temperature. Maximum speed if the housing cover has been opened. Sensor monitoring The removal of, o...

18 D2630 (RX600 S3) SAS Connectors and jumpers Features 3.6 Connectors and jumpers Figure 6: Schematic overview of the system board D2630 1 = J8C2 (jumper) 12 = Processor socket 4 2 = Memory board connector B 13 = Processor socket 3 3 = Memory board connector A 14 = SCSI connector channel A 4 = Batt...

20 D2630 (RX600 S3) SAS Connectors and jumpers Features J4A4 (29) - NVRAM Clear J8C2 (1) - BMC Reset 3.6.1 External connectors Figure 8: External connectors I/O shield LAN connectors On this system board you will find one GbE Broadcom LAN controller 5704C. This LAN controller supports the transfer r...

D2630 (RX600 S3) SAS 21 Features RoMB The LAN controller connectors are equipped with two LEDs (light emitting diode) indicating the transfer rate and the activity. Figure 9: LAN connectors 3.7 RoMB The onboard Intel ® IOP333 I/O processor becomes a RAID5 (RAID 0, 1, 5, 10, 50 ) controller by using ...

22 D2630 (RX600 S3) SAS Replacing the RAID Controller Features 3.8 Replacing the RAID Controller The MegaRAID™ SAS 8408E RAID controller is part of your system board D2630. It offers the following features: ● Eight internal SAS/SATA por ts - Two x4 SFF 8484 connectors ● 3 Gb/s throughput per por t ●...

26 D2630 (RX600 S3) SAS Replacing the RAID Controller Features Step 5 Installing the new RAID SAS controller Inser t the MegaRAID SAS controller in PCI Express slot #4 on the motherboard, as shown in the figure above. Press down gently but firmly to ensure the card is properly seated in the slot. Se...

D2630 (RX600 S3) SAS 29 4 Replacing the lithium battery In order to save the system information permanently, a lithium battery is installed to provide the CMOS-memory with a current. When the charge is too low or the battery is empty, a corresponding error message is provided. The lithium battery mu...

D2630 (RX600 S3) SAS 31 Abbreviations The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board. AC Alternating Current ACPI...

Comments on System Board D2630 for RX600 S3 SAS D2630 (RX600 S3) SAS Comments Suggestions Corrections ✁ Submitted by Fujitsu Siemens Computers GmbHUser Documentation33094 PaderbornGermany Fax: (++49) 700 / 372 00001 e-mail: [email protected] http://manuals.fujitsu-siemens.com