Fujitsu A20W-3 - Manuals

SCENICVIEW A20W-3/A22W-3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. ! i Supplementary...

SCENICVIEW A20W-3/A22W-3 ● No data transfer cables should be connected or disconnected during a thunderstorm. ● Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the device (danger of electric shock, short circuit). ● The device is not waterproof! Never immer...

SCENICVIEW A20W-3/A22W-3 Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements. ● The cable has to be HAR-certified or VD...

SCENICVIEW A20W-3/A22W-3 FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. NOTE: This equipment has been tested and found to compl...

SCENICVIEW A20W-3/A22W-3 Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation. ► Check whether ...

SCENICVIEW A20W-3/A22W-3 Installing an ergonomic video workstation 1 1 2 1 = Windows Avoid direct and reflected glare. Avoid glare from electric lighting. 1 = Edge of desk 2 = Permissible reaching sector Position the keyboard where it is easiest to reach. 30° 30° 65° 65° 0° 60° 1 2 2 1 = Bearing sur...

SCENICVIEW A20W-3/A22W-3 Mounting and removing the monitor base Mounting monitor base The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base. ! A26361-K1177-Z120-1-7619, edition 1 9

SCENICVIEW A20W-3/A22W-3 Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: ! The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket. ► Lay the monitor on its face on a soft su...

SCENICVIEW A20W-3/A22W-3 Connecting the monitor ! Please take note of the safety information in the "Important notes" chapter. CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. Do not cover the ventilation openings of the monitor. The compute...

SCENICVIEW A20W-3/A22W-3 ► Mount the cover over the connections. A lock (Kensington Lock) can be mounted in the security slot (4) to protect the monitor from theft. A Kensington Lock is not included in the consignment of the monitor. i Connecting cables to the computer Information on the computer co...

SCENICVIEW A20W-3/A22W-3 Operation of the monitor The monitor offers the following possibilities that enable it to be optimally adjusted for the respective user and the respective situation. Adjusting rake The rake of the monitor can be adjusted by –5° (forward) and +20° (back) from its vertical pos...

SCENICVIEW A20W-3/A22W-3 The power indicator (2) lights up blue when the monitor and computer are switched on. The power indicator lights up orange when the monitor does not receive a video signal or is in the energy saving mode. The power indicator goes off when the monitor is switched off. When yo...

SCENICVIEW A20W-3/A22W-3 Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs. Choosing basic monitor settings using the supplied software If o...

SCENICVIEW A20W-3/A22W-3 Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch. A message is displayed that the action has...

SCENICVIEW A20W-3/A22W-3 Notes on ergonomic colour adjustment If you select colours for the display in your application programmes, take note of the information below. The primary colours blue and red on a dark background do not produce the minimum required contrast of 3:1 and are therefore not suit...

SCENICVIEW A20W-3/A22W-3 Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the problem, please inform our help desk. Having this problem? Chec...

SCENICVIEW A20W-3/A22W-3 Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum pe...

SCENICVIEW A20W-3/A22W-3 Technical data A20W-3 A22W-3 Dimensions and weight Visible diagonals: 51 cm 56 cm Dot pitch: 0,28 mm 0,28 mm Screen size: Width: Height: 435.01 mm 272.47 mm 475.36 mm 297.70 mm Maximal resolution: 1680 x 1050 1680 x 1050 Dimensions incl. monitor base: Box dimensions: Width: ...

SCENICVIEW A20W-3/A22W-3 Environmental conditions Environment class 3K2, IEC 721 Rated range of operation: Humidity: 15 °C .... 35 °C 20 % .... 85 % Limit range of operation: Humidity: 5 °C .... 35 °C 20 % .... 85 % Condensation must be avoided. VESA-DDC-compatible VGA interface Your monitor is equi...

SCENICVIEW A20W-3/A22W-3 Pin assignment D-SUB 1 5 6 10 11 15 Pin Meaning Pin Meaning 1 Video input red 9 +5 V (DDC) 2 Video input green 10 Sync. earth 3 Video input blue 11 Earth 4 Earth 12 DDC-Data 5 Earth 13 H. sync 6 Red video earth 14 V. sync 7 Green video earth 15 DDC Clock 8 Blue video earth 2...