Fujitsu 3000 XL - Manuals

Preface TeamPoS 3000 XL and XL 2 ix Issue 3 D90000145 Table of Contents Preface ................................................................................................................... v Regulatory ..............................................................................................

TeamPoS 3000 XL and XL 2 Overview D900000145 Issue 3 1-1 Chapter 1. Overview This manual is provided to illustrate how to install and maintain the TeamPoS 3000 XL and XL 2 and describes in detail the procedures required for field installation and maintenance, including site preparation, equipment in...

TeamPoS 3000 XL and XL 2 Overview D900000145 Issue 3 1-2 1.1. TeamPoS 3000 Control Unit Flow Diagram (XL Motherboard only)

TeamPoS 3000 XL and XL 2 Overview D900000145 Issue 3 1-3 1.2. TeamPoS 3000 XL2 Control Unit Flow Diagram (XL 2 Motherboard only) USB (STD) operator panel XL Motherboard CPU: Celeron M Memory: 256 MB to 2GB DDR Lithium Battery: Pentium M soldered on the board Mini-PCI Slot 2.5" SATA HDD 2.5" ...

TeamPoS 3000 XL and XL 2 Overview D900000145 Issue 3 1-4 1.3. Front Panel LED's and Switches The following graphic and table show the TeamPoS 3000 unit LED's and switches: SD USB 1 Power SwitchOn/Off button located behinddrop down window. * Shown here-Drop downwindow in up position. USB 2 Power LED ...

TeamPoS 3000 XL and XL 2 Overview D900000145 Issue 3 1-5 1.3.1. TeamPoS 3000 Front Panel Switch and LCD Matrix Symbols Name Switch/LED Mounting Position LED Color Remark Power Switch Under drop down window in front panel -- Depending on the BIOS setup, the power switch can be instant off or delayed ...

TeamPoS 3000 XL and XL 2 Overview D900000145 Issue 3 1-6 1.4. Intelligent PIN's (Product Identification Numbers) TeamPoS 3000 Controller Intelligent PIN Configuration Guidelines 5 th Digit Interface Options 0: No I/O Card1: 3, 12V USB Ports3: Combo Board + Com Board **4: Combo I/O Board 8 th Digit I...

TeamPoS 3000 XL and XL 2 Environmental Specifications D900000145 Issue 3 2-1 Chapter 2 Environmental Specifications The figure below shows a typical integrated configuration for the TeamPoS 3000 XL 2 (black without cash drawer). Depending on the store environment, the configur ation and components m...

TeamPoS 3000 XL and XL 2 Environmental Specifications D900000145 Issue 3 2-2 2.1 Environmental Specifications for both XL and XL 2 Specifications Unit TP3000 XL & XL DT50III 2 With Covers CT10 Print er Compact Standard External dimensions mm (inches) Width 348 (13 6/8”) 450 (17 ¾”) 190 (7 3/8”) ...

TeamPoS 3000 XL and XL 2 Dimensions D900000145 Issue 3 3-1 Chapter 3 - DIMENSIONS This section shows the dimensions of the TeamPoS 3000 XL and XL 2 control units and peripherals. For 3 rd party peripherals not shown, refer to the appropriate 3 rd party manufacture documentation. Note: All dimensions...

TeamPoS 3000 XL and XL 2 Dimensions D900000145 Issue 3 3-3 Dimensions shown above indicate the smallest space requirement to accommodate the pr inter overhang, the LCD overhang and the keyboard overhang.. The largest space required to accommodate the widest spread of the monitor arms and the greates...

TeamPoS 3000 XL and XL 2 Dimensions D900000145 Issue 3 3-4 3.3 Keyboards 3.3.1 Model 133 UQ Keyboard Dimensions (PIN #s 90000829 white, 900001519 black) 3.3.2 Model 133 AU Keyboard Dimensions (PIN #’s 11001689 white, 11001699 black) 450 17 ¾” 202 7 7/8” 43 1 6/8” Height at the rear 450 (17 ¾”) 202 7...

TeamPoS 3000 XL and XL 2 Dimensions D900000145 Issue 3 3-5 3.3.3 Model 92U Keyboard Dimension (PIN # 90000630) 3 . 4 Cash Drawers 3.4.1 Model TP15 Cash Drawer - Standard (11001467 white w/o lock, 11000153 white w/lock, 11001468 black w/o lock, 11000154 black w/lock) Standard Cash Drawer 140 5 ½” 140...

TeamPoS 3000 XL and XL 2 Dimensions D900000145 Issue 3 3-8 3.5 Displays 3.5.1 Model D22 LCD and Model D25 LCD Displays Two LCD’s are offered for use with the TeamPoS 3000 XL and XL 2 controller. The D22 LCD is a 12.1” LCD and the Model D25 LCD is a 15” LCD. Both LCD’s support both analog and digital...

TeamPoS 3000 XL and XL 2 Dimensions D900000145 Issue 3 3-16 3.6 Printers Two printers are available for the TeamPoS 3000 XL and XL2: the DT50I II and the CT10. Their dimensions are show in the figures that follow. 3.6.1 Model DT50III Printer (PIN #’s 11000187-white, 11000197-black) 3.6.2 Model CT10 ...

TeamPoS 3000 XL and XL 2 Site Preparation D900000145 Issue 3 4-1 Chapter 4 SITE PREPARATION This chapter defines the following pre-installation details for the TeamPoS 3000: • Shipment inspection and return • Anti-static protection • Electrical supply requirements • Mains power cables • Warning labe...

TeamPoS 3000 XL and XL 2 Site Preparation D900000145 Issue 3 4-3 4.5 Preparing for Installation: Before installing equipment, perform the following steps: • Move all terminal components, accessories, and cables to the locations specified in your local site plan. • Position the cables according to th...

TeamPoS 3000 XL and XL 2 Site Preparation D900000145 Issue 3 4-4 4.7 General Requirements 1. The safety standards for Information Technology Equipment are only valid if the building installation conforms to the National Electrical Code for the country where the equipment is being installed. 2. For e...

TeamPoS 3000 XL and XL 2 Site Preparation D900000145 Issue 3 4-6 4.8 Installation with Other Equipment In most cases, dedicated AC mains circuits are not required for the TeamPoS 3000XL and XL 2 terminals. In rare instances, other electrical equipment sharing power with the terminal may cause advers...

TeamPoS 3000 XL and XL 2 Site Preparation D900000145 Issue 3 4-8 Back View of control unit Bottom of the TeamPoS Controller

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-1 CHAPTER 5 INSTALLATION Caution: Confirm that the external power source is 100-240 VAC before starting the operation. To prevent electric shock, confirm that the AC cable is removed from the AC outlet anytime the panels are removed. Be sure...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-4 3. To reinstall the rear panel, insert the metal tabs into the sides of the chassis and slide the locking tabs down. 5.2 Removing the motherboard assembly Caution: Be sure to observe all ESD precautions and power off procedures. 1. Remove ...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-6 5.3 Installing CPU and Heat Sink Caution: Be sure to observe all ESD precautions and power off procedures. The heat sink and CPU are installed on the motherboard (towards the front of the motherboard) just to the right of the memory. Both ...

TeamPoS 3000 XL and XL 2 Installation 5-8 Issue 3 D900000145 10. Reinstall the motherboard (See Section 5.2). 11. Reinstall the front panel and reconnect the power cable (See Section 5.1.1). 12. Reinstall the back panel (see Section 5.1.2). 5.4 Installing the Hard Disk Drives Caution: Be sure to obs...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-13 7. If two memory sticks are being installed, insert the 2 nd stick in the top slot following the same procedure as for the first. XL 2 Motherboard w/o memory sticks XL 2 Motherboard w/1 memory ready to install XL 2 Motherboard with 1 stic...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-15 5.7. Installing the CD/DVD Drive Caution: Be sure to observe all ESD precautions and power off procedures. The CD/DVD drive rides on top of the motherboard assembly and requires a narrow Phillips-head screwdriver to install. 1. Remove the...

TeamPoS 3000 XL and XL 2 Installation 5-18 Issue 3 D900000145 5.8. Installing the Partial Backup Battery Caution: Be sure to observe all ESD precautions and power off procedures. The partial backup battery is located on the front of the TeamPoS 3000XL and XL 2 on the left. 1. Remove the rear panel (...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-20 5.9. Removing the Backplane Assembly Caution: Be sure to observe all ESD precautions and power off procedures. 1. Remove the rear panel (See Section 5.1.2). 2. Disconnect the AC power cord from the controller. 3. Remove the front panel (S...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-26 5.11.2 Powered USB I/O Board Caution: Ports designated as Port C on the backplane (24V PUSB) and Port 3 on the Combo board (24V RS232) do not meet UL limited power source (LPS) requirements. These ports are limited to only allowing 24V Re...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-29 5.11.3 Combo Board Caution: Be sure to observe all ESD precautions and power off procedures. Combo Board with XL 2 Motherboard Combo Board and Com Board with XL Motherboard

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-30 Caution: Ports designated as Port C on the backplane (24V PUSB) and Port 3 on the Combo board (24V RS232) do not meet UL limited power source (LPS) requirements. These ports are limited to only allowing 24V Retail POS RS232 or powered USB...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-33 5.11.4 Combo Board with COM Board (XL Motherboard only) (XL 2 Motherboard does not support the COM board) Caution: Ports designated as Port C on the backplane (24V PUSB) and Port 3 on the Combo board (24V RS232) do not meet UL limited pow...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-41 5.14.1. Single Stacked LCD Stand Single Stacked LCD Stand 1. Remove only the hinge cap and cable access cover from the stand; leave the top and bottom hinge cover in place. Some photos in this section show the top and bottom hinge cover a...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-44 Typical VGA Cabling 10. Attach the stand to the back of the LCD with the screws provided. Make sure that the tabs on the bottom hinge cover fit into the notches in the back of the LCD. To assure proper alignment of the LCD, attach screws ...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-46 5.14.2 Single Dispersed LCD Stand 1. Remove only the hinge cap from the stand; leave the top and bottom hinge cover in place. Some photos in this section show the bottom hinge cover and top hinge cover removed in order to more clearly sho...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-49 6. Attach the cables to the connectors on the LCD. Connector labels are etched into the plastic casing of the LCD monitor. Typical VGA Cabling VGA (required) pUSB (required) Audio (optional) Mounting Bracket DVI VGA A to B USB for opt. MS...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-50 7. Attach the stand to the back of the LCD with the screws provided. VGA Configuration with Attached Stand Mounting Screws

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-53 5.14.3 Dual Stacked LCD Stand 1. Remove only the hinge caps and cable access cover from the stand; leave the top and bottom hinge covers in place. Some photos in this section show the bottom hinge cover and top hinge cover removed in orde...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-57 5.14.4 DVI15 LCD The DV15 LCD comes in two configur ations, touch and non touch. Integrated stand and speakers are standard in both configurations. A VGA cable for video is also included. If mounting the LCD on a VESA mounted check stand,...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-58 Touch Configuration with A-B USB and Power Brick Unscrew these four screws for VESA mounting Remote Power Supply VGA Audio Separate A-B cable

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-59 DV15 ready for VESA mounting

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-60 Connecting/ Forming the Cables (1) Open the Back Cover - Press the side wall of the stand, and then remove the Back Cover. (2) Plug the audio, VGA, power, and USB(DV15-31 Touch Panel Model only) - Connect the cables to the controller as f...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-67 5.16. Installing the VF60 in Stacked Stand Parts required for assembly of the VF60 customer display in the stacked stand: • VF60 display (2x20) • LCD stacked stand • Adjustable pole • Cosmetic collar • Tilter unit • Powered USB cable (pUS...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-72 5.17. Stacking the LCD Monitor The LCD stacked monitor stand has notches in the bottom that fit over the LCD brackets attached to the top of the controller. There are also latches in the bottom of the stand that provide additional securit...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-75 5.18. Installing the Central Filler and Keyboard 5.18.1 Installing the Keyboard 1. Insert the keyboard cable into the USB connector on the bottom of the keyboard. Run the cable through the strain relief clip, and then out the back of the ...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-80 5.20. Stacking the Printers Both the DT50 Series and the CT-10 printers stack on the TeamPoS 3000 controller and are restrained from shifting by brackets attached to the controller. A filler is used to occupy the free space on a standard ...

TeamPoS 3000 XL and XL 2 Installation D900000145 Issue 3 5-82 5.20.2. Stacking the CT10 Printer 1. Install Central Filler (See Section 5.17.2) 2. Install narrow Side Filler by placing it on the chassis with the front edge aligned with the Central Filler and ½” to the left of the Central Filler (faci...

TeamPoS 3000 XL and XL 2 General Operations D900000145 Issue 3 6-1 Chapter 6 - General Operations 6.1 System Operations This section contains general and periodic care and maintenance, and power ON and OFF procedures for the TeamPoS terminals. 6.1.1 General Care and Maintenance General cleaning of t...

TeamPoS 3000 XL and XL 2 General Operations D900000145 Issue 3 6-2 5. If the keyboard or LCD has the MSR option installed, pass a magnetic stripe reader cleaner through the magnetic stripe reader to remove dust particles from the reader. The cleaner is a card covered with cloth on one side. Pass the...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-1 Chapter 7 - Maintenance Caution: Confirm that the external power source is 100-240 VAC before starting the operation. To prevent electrical shock, confirm that the AC cable is removed from the AC outlet anytime the covers are removed. Be su...

TeamPoS 3000 XL and XL 2 Maintenance 7-4 Issue 3 D900000145 7.2 Replacing the Motherboard Caution: Be sure to observe all ESD precautions and power off procedures. Before installing a new motherboard, ensure that the replacement motherboard jumpers have been set correctly. (See Section 7.3.1 Motherb...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-11 7.2.4 XL2 Motherboard Layout J1 -A J1 -B J 1 -C SAT A (for kiosk mode) To OP Panel To Heatsink Fan SAT A 0 SAT A 1 J4 Heat Sink CPU under heatsink & fan GME 965 North Bridge (under heatsink) J5 J8 J1 0 JP1 J1 1 5 VSB LE D ICH8 South Br...

TeamPoS 3000 XL and XL 2 Maintenance 7-14 Issue 3 D900000145 7.3 Replacing the CPU and Heat Sink Caution: Be sure to observe all ESD precautions and power off procedures. The heat sink and CPU are installed on the front of the motherboard (viewed from the front of the unit) just to the right of the ...

TeamPoS 3000 XL and XL 2 Maintenance 7-16 Issue 3 D900000145 7.4 Replacing the Hard Disk Drives Caution: Be sure to observe all ESD precautions and power off procedures. 1. Remove the front panel (See Section 5.1.1). 2. Remove existing hard dr ive from motherboard by pressing down on the metal tab (...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-17 5. Press firmly to make the connection. 6. Reinstall the front panel (See Section 5.1.1). 7. If this is an upgrade, install the upgrade label that comes with the upgrade kit to the side of the unit near the serial number. (See Section 7.2)...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-19 7.5.2 Adding or Replacing XL2 Motherboard Memory Caution: Be sure to observe all ESD precautions and power off procedures. The TeamPoS 3000 XL 2 1. Remove the rear panel, (See Section 5.1.2). Motherboard has two memory sockets or slots and...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-25 12. Reinstall the back panel (See Section 5.1.2). 13. If this is an upgrade, install the upgrade label that comes with the upgrade kit to the side of the unit near the serial number. (See Section 7.2). 7.7 Replacing Battery Backup Caution:...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-27 7. Attach the protective front cover with retained screws. 8. Reinstall the front panel and reconnect the power cable (See Section 5.1.1). 9. Reinstall the back panel (See Section 5.1.2). 10. If this is an upgrade, install the upgrade labe...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-39 7.9.3.2 Combo Board Diagram The following illustration shows the TeamPoS 3000 XL and XL 2 COM IN COM OUT UBS IN COM 3 COM 4 P-USB6 (12V) P-USB5 (12V) P-USB4 (12V) P-USB3 (12V) P-USB2 (12V) P-USB1 (12V) 1 1 1 1 1 1 JP 1 JP 2 JP 3 JP 4 JP 5 ...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-43 7.9.3.6 Printer (PTR) Connector signals Connector type: Female D15 Pin # Signal ESC/PoS Mode 1 GND 2 RX 3 TX 4 CTS 5 DSR 6 CD 7 SG 8 +24V RET 9 RI 10 +5V 11 DTR 12 RTS 13 GND 14 +24V 15 +24V 8 1 15 9

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-53 7.11 Replacing the Power Supply 1. Remove the back panel (See Section 5.1.2). 2. Disconnect the power cable from the controller. 3. Remove the front panel (See Section 5.1.1). The yellow LED light should be off (See Section 1.2). 4. Unseat...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-55 7.12 Replacing the Power Supply Fan 1. Remove the back panel (See Section 5.1.2). 2. Disconnect the power cable from the controller. 3. Remove the front panel (See Section 5.1.1). The yellow LED light should be off (See Section 1.2). 4. Un...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-57 7.13 Replacing the Backplane Caution: Be sure to observe all ESD precautions and power off procedures. The backplane assembly contains the power supply and I/O boards. The backplane PCB is spared as an individual board and requires removal...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-61 7.13.1 Backplane Jumpers & Connectors PCI slot for add in cards JP1 – Power source selection for USB1 1-2 = Normal +5V (default) 2-3 = Standby +5V JP5 – Signal Source selection for COM2 1-2 = RI (default ) 3-4 = +5V 5-6 = +12V JP4 – Si...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-62 7.13.2 TeamPoS 3000 Pin Assignments - Backplane Cash Drawer COM1 & 2 USB +24V Red powered USB connector 1 +24V Return 5V USB Pwr 2 Dwr1 Status Data - 3 Dwr1 Kick Data + 4 Gnd – dual CD Gnd 5 Gnd +24V Return 6 Gnd – Dual CD +24V Pwr 7 D...

TeamPoS 3000 XL and XL 2 Maintenance D900000145 Issue 3 7-63 This Page Intentionally Left Blank

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-1 Chapter 8 - Troubleshooting 8.1 Power cannot be turned on or the unit powers off after a few minutes. The power LED next to the power switch does not light up. NOTE: Assume Windows operating system and OPOS/JavaPOS No Check item Judgmen...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-2 8.2 System will not boot up (The system fails to start up even though the power is turned on) No Check item Judgment Action 1 Is data displayed on the monitor during Power On Self Test (POST)? Y N Go to No. 2., or go to LCD troubl eshoo...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-5 8.5 Printing errors No Check items Judgment Action 1 Is receipt paper set correctly? Y N Go to No. 2. Set the receipt paper correctly. 2 Can you feed the paper with the paper feed key? Y N Go to No. 5. Go to No. 3. 3 Is the printer cabl...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-6 8.6 Impossible to input data from keyboard and/or abnormal input No Check item Judgment Action 1 Is the cable connected correctly? Y N Go to No.2. Connect the cable correctly. 2 Is the keyboard set correctly? If the keyboard is a 133UQ ...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-7 8.7 Keyboard MSR reading error No Check item Judgment Action 1 Is the keyboard cable connected correctly? Y N Go to No.2. Connect the cable correctly. 2 Does the magnetic card meet ISO standards? Y N Go to No.3. Try a known good card an...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-8 8.8 Cash Drawer Operation errors No Check item Judgment Action 1 Is the cash drawer cable connected correctly? Y N Go to No.2. Connect the cable correctly. 2 Can the cash drawer be activated by WINCLD diagnostics? Y N Check the OPOS/Jav...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-9 8.10 Deletion of Date, time and disk setup data when turning off power No Check item Judgment Action 1 Is the voltage of the lithium battery on the motherboard normal? Y N Go to No.2. Change the motherboard. 2 Is the “Clear CMOS” jumper...

TeamPos 3000 XL and XL 2 Troubleshooting D900000145 Issue 3 8-10 8.12 Operation errors of other peripheral devices No Check item Judgment Action 1 Is the cable connected correctly? Y N Go to No. 2. Connect the cable correctly. 2 Does WINCLD operate properly with this peripheral? Y N Check the progra...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-1 Chapter 9. BIOS Setup Procedures – Aurora Motherboard If a motherboard is replaced in the field, it may be necessary to change the date and time and setup the BIOS for the customer ’s configuration. The following information shows t...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-2 9.1.2 Main Menu – Motherboard Note: An arrow [  ] indicates additional screens. Use [Enter] to advance to the next screen. Text shown in blue is dynamic, meaning it both changes as the unit operates, or it is set for automatic mode...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-5 9.1.5 CPU Feature Setup - Motherboard Factory Default Settings Phoenix – AwardBIOS CMOS Setup Utility CPU Feature Manufacturer Intel CPU Type Celeron M Mobile CPU Frequency 1300 MHz FSB Speed 400 MHz Cache L1 32KB Cache L2 512 KB Ca...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-7 9.1.7 Advance Chipset Features Setup- Motherboard Factory Default Settings Phoenix – AwardBIOS CMOS Setup Utility Adv anced Chipset Features DRAM Timing Selectable [By SPD] x CAS Latency Time 2.5 x Active to Precharge Delay 7 x DRAM...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-9 9.1.9 USB Configuration Setup - Motherboard Factory Default Settings Phoenix – AwardBIOS CMOS Setup Utility USB Configuration NEC USB Configuration: None ICH4 USB Configuration : USB Beep Message [Disabled ] Emulation Type [Auto] De...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-10 9.1.11 Onboard Device Setup - Motherboard Factory Default Settings Phoenix – AwardBIOS CMOS Setup Utility Onboard Device USB Controller [Enabled] USB 2.0 Controller [Enabled] Legacy USB Support Enabled AC97 Audio [Auto] Init Displa...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-16 9.1.19 System Information - Motherboard Factory Default Settings Phoenix – AwardBIOS CMOS Setup Utility System Information Bios Version 6.00 PG Product Name Aurora Build Date 2008/08/12 BIOS ID P17 Processor Type Celeron-M Mobile C...

TeamPos 3000 XL and XL 2 BIOS XL Motherboard D900000145 Issue 3 9-17 9.1.20 Set Supervisor/User Passwords - Motherboard Factory Default Settings Phoenix – AwardBIOS CMOS Setup Utility Set Supervisor/User Password Set Supervisor Password [PRESS ENTER] Set User Password [PRESS ENTER] Super Password St...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-1 Chapter 10. BIOS Setup Procedures – XL 2 If a motherboard is replaced in the field, it may be necessary to change the date and time and setup the BIOS for the customer ’s configuration. The following information shows the default...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-2 10.1.2. Main Menu – XL2 Motherboard Note: An arrow [  ] indicates additional screens. Use [Enter] to advance to the next screen. Text shown in blue is dynamic meaning it either changes as the unit operates, or it is set for auto...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-3 10.1.3. IDE Primary/Master Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit IDE Primary/Master [DW-224E-C-(PM)] Item Specific Help Type : [Auto]...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-5 10.1.5. SATA Port 1 Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit SATA Port 1 [HTS541040G9SA00- (S1)] Item Specific Help Type : [Auto] User =...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-6 10.1.6. SATA Port 2 Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit SATA Port 2 [None] Item Specific Help Type : [Auto] User = you enter parame...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-7 10.1.7. SATA Port 3 Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit SATA Port 3 [None] Item Specific Help Type : [Auto] User = you enter parame...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-8 10.1.8. Advanced Main Menu – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit Item Specific Help  CPU Feature  GM965 Feature  ICH8MDO Feature  Super...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-11 10.1.12. USB Feature Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit USB Feature Item Specific Help USB Controller: [Enabled] USB 2.0 Controll...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-12 10.1.13. ICH SATA PATA Control Sub-Menu Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit ICH SATA PATA Control Sub-Menu Item Specific Help SATA...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-13 10.1.14. Super IO Feature Setup – XL 2 All options are shown here, however on the BIOS screens it will be necessary to scroll down to see all the options: Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility M...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-17 10.1.19. Power Setup – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit Item Specific Help ACPI Function [Enabled] Disable ACPI _Sx: [None] Soft-Off by...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-18 10.1.20. Boot Setup – XL 2 All options are shown here, however on the BIOS screens it will be necessary to scroll down to see all the options: Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced...

TeamPoS 3000 XL and XL 2 BIOS XL 2 Motherboard D900000145 Issue 3 10-19 10.1.21. Exit Menu – XL 2 Factory Default Settings Motherboard Phoenix TrustedCore™ Setup Utility Main Advanced Security TPM State Power Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Default...

TeamPoS 3000 XL and XL 2 Spare Parts D900000145 Issue 3 11-1 Chapter 11 SPARE AND UPGRADE PARTS LIST Parts labeled “Reference only” are not orderable and are listed for reference only. Part numbers with the extension "K" are Field Upgrade Kits. DESCRIPTION FTXS # COMMENT TeamPoS 3000 XL/XL2 ...

Spare Parts TeamPoS 3000 XL and XL 2 D900000145 Issue 3 11-2 DESCRIPTION FTXS # COMMENT CPU, Intel, Celeron M, 1.5 GHz 11000234 HeatSink - Socket 479 11000235 OPN TP3K CPU/1.6 Pentium M 11000029 XL Motherboard Only CPU, Intel, Pentium M, 1.6 GHz 11000239 HeatSink - Socket 479 11000235 OPN TP3K CPU/2...