Dolmar MS-330 U - Manuals

Dolmar MS-330 U – Manual in PDF format online.

Manuals:

Manual

Manual Dolmar MS-330 U

Summary

Page 2 - Table of contents; Page; Cleaning the air filter; Packing; We trust that you will be a satisfied customer. By choosing; EU Conformity Declaration

Table of contents Page EC declaration of conformity ............................................ Packing ................................................................................ Delivery inventory .............................................................. 3 Explanation of symbols ..........

Page 3 - STOP; Explanation of symbols; If one of these parts is missing when you unpack the brushcutter,

3 12 Shown: MS-60 U STOP read the instruction manual and follow all warnings and safety instructions! Particular care and caution! forbidden! wear protective gloves! wear safety shoes! wear head, eye, face and hearing protec- tion! The distance between the machine and bystanders shall be at least 50...

Page 4 - SafETy PrECaUTIonS; general precautions; and persons under the influence of alcohol, drugs or medication; Personal protective equipment; it should be tight-fitting but not cause hindrance. Do not wear; Handling fuels / refuelling; - Keep away from open flame or sparks and do not smoke while

4 SafETy PrECaUTIonS general precautions Proper use: These power brushcutters are intended for cutting grass or heavy weeds, with the appropriate and permissible cut- ting tools. A brushcutter may be operated only by one person, and only out of doors! Improper use: The cutting tools permissible for ...

Page 5 - Putting into operation; are intended for as specified in the documentation.

5 - Ensure that no fuel or chain oil oozes into the soil (environmental protection). Use an appropriate base. - Refuelling is not allowed in closed rooms. Fuel vapors will accumulate near the floor (explosion hazard). - Carefully tighten the locking screw of the fuel tank and inspect the fuel cap at...

Page 6 - kickback; This can fling the brushcutter to one side with great force and; working behavior / Method of working

6 14 15 11 1 13 kickback During operation the brushcutter can kickback in an uncon- trolled manner. This can happen when the cutting blade (4- tooth star blade) comes into contact with hard objects such as stumps, fenceposts, tree trunks, woody brush or large rocks. This can fling the brushcutter to...

Page 7 - make any modifications to the brushcutter ‐ you will only be; tools and fixing devices of cutting tools, or accessories.; first aid; A first-aid kit should always be nearby as a precaution in the; SErVICE

7 Storage - The brushcutter must be safely stored in a dry room. Use the tool protection for metal cutting tools. Keep the brushcutter out of reach of children. - If the brushcutter is stored for a long period of time, it should be given a thorough maintenance check and a complete inspection at an a...

Page 8 - Technical Data; Specific consumption per ISO 8893; Type plate; Components

8 1) The maximum rated speed of the trimmer head is not exceeded when using a DOLMAR trimmer head. ) Figures derived in equal part from idle and top-speed operation (per EN-ISO 11806). 3) At max. power Technical Data 230 C | 260 C | 330 C Displacement cm 3 .6 | 5.6 | 3.6 5.6 | 3.6 | 4.7 Bore mm 31 |...

Page 9 - PUTTIng InTo oPEraTIon; cap and wear protective gloves!; ing them able to be turned for final positioning.; Installing the handle

9 PUTTIng InTo oPEraTIon STOP CaUTIon: when working on the brushcutter always be absolutely certain to switch off the engine, pull the spark plug cap and wear protective gloves! IMPorTanT: Do not start the brushcutter until fully assembled and inspected! A - Loosen screws ( a/1 ) and unscrew about 1...

Page 10 - Installing the cutter guard; ter to the upper part of the cutter guard (; Cutting tool

10 6 7 8 Installing the cutter guard Cutting tool Cutter guard Tool/guard combinations for the MS-260 U / MS-330 U / MS-430 U A 4-tooth star blade: Part no. 36 4 140 Part no. 351 504 101 Outside diameter: 30 mm (9"), arbour: 5,4 mm (1") 2-line trimmer head Part no. 351 50 030 Part no. 351 50...

Page 12 - replacing the line; - To do this, push the button firmly and pull out the line ends; replacing the line knife; firmly, the protective hood must be replaced.; adjusting the line

1 F replacing the line - You can adjust the line to the right length at any time by lightly tapping the trimmer head against the ground (direction of arrow). The line cutter automatically cuts off excess line. However, this only works when at least 3 cm of line are vis- ible at each end. - If the li...

Page 13 - foLLow THE SafETy PrECaUTIonS!; refuelling; It is not wise to add more oil to the mixture than specified,; fuel mixture

13 aVoID SkIn anD EyE ConTaCT! Utmost care is required when handling fuel. Fuel may contain substances similar to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel vapours. Fuel vapours are poisonous and can be hazardous to your health. Avoid eye and skin contact with...

Page 14 - Putting on the harness; Put on the harness as shown in figure A.; - In difficult terrain or when using the steel bush cutter the; Balancing the brushcutter; the red release tab is not on the inside towards the oper-

14 Putting on the harness - Put on the harness as shown in figure A. - Adjust it so that the clip is about a hand-width above your hipbone. A B - Correctly balancing the brushcutter reduces strain on the arms while working. - When using the trimmer head on a level terrain, the trimmer head should to...

Page 15 - Cold start; Now pull quickly and forcefully until you hear the first; warmstart; Idle adjustment

15 Cold start F - Prime the fuel pump ( g/5 ) by pressing it several times until you can see fuel in the pump. - Actuate the half-throttle lock by depressing the safety lock ( f/3 ), pressing in the throttle ( f/1 ) and moving the combi- nation switch ( f/2 ) into the STarT position. Then release th...

Page 16 - rEPaIr anD MaInTEnanCE work; ualified; Instructions for maintenance

16 rEPaIr anD MaInTEnanCE work CaUTIon: Before doing any work on the brushcutter, always switch off the motor and pull the plug cap off the spark plug . always wear protective gloves! CaUTIon: Start the brushcutter only after complete assembly and inspection! general The brushcutter Clean exterior, ...

Page 17 - - Take the foam filter out of the cover.; If the air filter is damaged replace it immediately!; Inspecting the

17 Cleaning the air filter - Loosen the screws ( a/1) and remove the air filter cover ( a/2 ). - Take the foam filter out of the cover. Caution: To prevent eye injuries, do not blow out dirt particles! - Very dirty filters can be cleaned out using regular dishwash - ing liquid in lukewarm water. - I...

Page 18 - Cleaning the muffler opening; Service; Servicing and maintenance

18 Trouble shooting After about 50 operating hours the gear box ( D/8 ) should be checked by a OLMAR service centre, and if necessary re- grease.The service centre will add the exact amount of grease, as excessive grease will lead to overheating of the gearbox. Lubricating the gear box The felt filt...

Page 19 - Service, spare parts and guarantee; Maintenance and repair; used. Use only original DOLMAR parts, marked; Extract from the spare parts list

19 Service, spare parts and guarantee Maintenance and repair The maintenance and repair modern brushcutters and safety-related components and assemblies requires qualified technical training and a workshop equipped with special tools and testing devices.Any maintenance or adjustment work not describ...

Page 20 - guarantee; by a DOLMAR service centre.

0 guarantee DOLMAR guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular guarantee conditions ma...

Page 21 - notes

Page 24 - DOLMAR GmbH

Form: 995 703 48 (10.06 GB) Specifications subject to change without notice DOLMAR GmbH Postfach 70 04 0 D-004 Hamburg Germany http://www.dolmar.com To find your local distributor, please visit www.dolmar.com