Delta 22-610 - Manuals

7 UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gaso-line or lacquer thinner for this purpose...

8 ASSEMBLY ASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATE - 2-3 hours * Open end wrenches (supplied)* Hex wrenches (supplied)* Flat screwdriver (not supplied) UNLOADING ANDPOSITIONING MACHINE This machine should be unloaded using a crane andslings around and under the table on both sides, asshown in...

9 To connect power to your machine, proceed as followsfor either 200-230/460 volts, three phase operation. 1. Remove the four screws, one of which is shown at (A) Fig. 4, and remove cover (B). 2. Insert power line through entrance hole (E) and con- nect the three power lines to terminals L1, L2 and ...

10 OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS STARTING AND STOPPING THE PLANER The machine is started by pressing the green (shroud-ed) "ON" button (A) and stopped by pressing the red(mushroom type) "OFF" button (B), as shown in Fig. 8. Fig. 8 TABLE RAISING ANDLOWERING CONTROLS D...

14 Fig. 21 Fig. 22 Fig. 22A LEVELING THE TABLE The table must be parallel to the cutterhead knives. Tocheck and adjust, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the four screws that attach the top cover to the planer and carefully remove the top cover. 3. Place a straigh...

16 Fig. 24B Fig. 25 Fig. 26 ADJUSTING PRESSURE BAR IMPORTANT: THE PRESSURE BAR IS SET AT THE FACTORY AND SHOULD NOT NEED ASJUSTMENT.BUT WHEN KNIVES ARE SHARPENED ORREPLACED THE PRESSURE BAR SETTING SHOULDBE CHECKED AND ADJUSTED IF NECESSARY. The pressure bar is located directly behind the cutter-hea...

17 ADJUSTING THE CHIPBREAKER The chipbreaker is located on the top of the planer andextends down around the front of the cutterhead. Thechip-breaker segments raise as stock is fed through and"break or curl" the chips the same as the plane iron capon a hand plane. The bottom of the chipbreake...

18 ADJUSTING SPRING TENSION ON FEED ROLLERS The outfeed roll (A) Fig. 33, and infeed roll (not visible)are those parts of your planer that feed the stock whileit is being planed. The feed rolls are under spring tensionand this tension must be sufficient to feed the stock uni-formly through the plane...

19 Fig. 38 Fig. 39 Fig. 40 ADJUSTING CHIP DEFLECTOR 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the cutterhead guard. 3. The edge (C) of the chip deflector (A) Fig. 38, should be adjusted so it is a minimum of .040" and a maximumof .080" away from the cutting circle. Place a feelergaug...

20 When using your machine, follow these few simple steps for achieving the best results. 1. True Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you planed in STEP 1 face down and feed...

21 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality pro...

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...